Training
Profile
Introduction to how to add feedback control to a dc-dc converter. The plant, control objective, and controller for feedback control of a dc-dc converter are described.
This article introduces how to add feedback control in a DC converter, and describes the devices, control objects and controllers used for feedback control of dc-DC converters.
Chapters
Chapter 1：DC-DC Converter Control- Introduction (6 minutes and 5 seconds)
Chapter 2：DC-DC Converter Control- Modeling (5 minutes and 57 seconds)
Chapter 3：DC-DC Converter Control- More Modeling (6 minutes and 42 seconds)
Chapter 4：DC-DC Converter Control- Feedback Control Loop (6 minutes and 14 seconds)
Chapter 5：DC-DC Converter Control- Feedback Controller (8 minutes and 48 seconds)
You Might Like
Recommended Posts
- Mplab X IDE C language optimization level setting
- I encountered a strange problem when debugging the program. I suspected that the optimization level was set too high, but I couldn't find where to set it.
-
sgfwin
Microchip MCU
- How to convert English characters into TP-DU code
- How to convert English characters into TP-DU code? There are small tools on the Internet that can convert Chinese characters into UTF8 code, but how can I convert quotation characters into TP-DUL code
-
xuzhanglong
NXP MCU
- No matter what, in the end it will turn into people fighting people.
- [i=s]This post was last edited by led2015 on 2020-2-18 21:47[/i][No matter what happens, it will eventually turn into a fight between the people, so the community should not exceed 140 people]I recent
-
led2015
Talking
- The debugger in ADS compiles correctly, but an exception occurs when running
- AREA Jump, CODE, READONLY ; name this block of codeCODE32num EQU 2ENTRY ; Program entry flag start MOV r0, #0 BL Func stopMOV r0, #0x18 ; Exit from applicationLDR r1, =0x20026 ;SWI 0x123456 ; Func CMP
-
skyflysgs
ARM Technology
- 【Project source code】Timer based on FPGA TFT implementation
- Adopts ac620 board, 5.0tft display The module software is PCtoLCD2002, 16 width, 8 pixels per character quartus 13.0 verilog implementation is not niosFunctions implemented: The top layer of TFT displ
-
小梅哥
Altera SoC
- Disassembly of electric kettle switch
- The switch of the electric kettle at home is broken, so we disassembled it to check. 1. Open the arc handle, and the problem comes out: the screws are rusted, so we remove them forcibly.2. Disassemble
-
ths9366
Making friends through disassembly
Recommended Content
Web users are watching Change
- Mplab X IDE C language optimization level setting
- How to convert English characters into TP-DU code
- No matter what, in the end it will turn into people fighting people.
- The debugger in ADS compiles correctly, but an exception occurs when running
- 【Project source code】Timer based on FPGA TFT implementation
- Disassembly of electric kettle switch
- LED needs aluminum substrate reason
- Design of vehicle multimedia navigation system based on 32-bit system
- lm3s boot_loader
- Give out red envelopes on the first day of work
- Is there a minimum system circuit diagram?
- [Modelsim FAQ] Error deleting "msim_transcript": permission denied...
- EEWORLD University Hall----WEBENCH design tool performance enhancement
- A small problem with the timer triggering the ADC module
- Please share your experience in soldering circuits (for beginners)
- Design and Research of Low Power Consumption of DSP Processor
- About the problem of downloading the program of LM3S811 adapter board
- Is iPhone 4 worth waiting for?
- Kernel compilation error under CE X86, please help, urgent
- Under ce6, I want to make a more general driver to control the gpio port. I would like to hear your better suggestions.
- I am studying international economics and trade, and I have never studied electronics before. Due to work needs, I want to learn more about CCL and FE-4. Where can I find this knowledge online? What other books or materials can explain this?
- HDP503 Universal Pressure Transmitter
- Such a good board, no one claims it!
- How to bind multiple IP addresses to a physical network port in vxWorks
- Selection of power inductor
- Frequency band characteristics and main application areas of RFID system
- Design of intelligent charger based on AT89S52
- Please recommend a boost boot chip
- HY-STM32 data with lots of examples
- Concepts and differences of GPRS, 433, Wifi, and Zigbee modules
Popular Components
Just Take a Look
Hot Downloads
- The functions of this system are as follows: 1. This system provides multiple choice questions
- Principles and applications of classic single chip microcomputers
- Discussion on the Implementation of Negative Feedback Amplifier Circuit
- Solar physics
- csf file player Chinese version
- When working with mathematical simulations or engineering problems, it is not unusual to handle curv
- Modular programming notes
- Journal article: A segmentation algorithm for industrial CT images
- CL1221
- eml17
MoreHot Articles
- Analysis of white LED backlight dimming solution
- Mouser Now Stocking Qorvo QPQ1298 High-Performance BAW Filter
- Groundbreaking Bayesian Deep Learning Enables Energy-Efficient AI
- Ask the court to declare that its 5G patent licensing rates comply with the FRAND principle
- STM32 collects signals from DHT11 temperature and humidity sensor
- How to operate an infrared spectrophotometer?
- STM8L151C8 MCU learning routine (13) - DHT11
- Details determine success or failure--Three key points in the design of the power supply system of the electronic blood pressure monitor
- Huawei's fourth major event: seven years of planning and three years of invisibility, what are the chances of success or failure?
- Qualcomm presents industry-leading AI innovations and collaborations at CES 2025, covering PCs, cars, smart homes and enterprise
京公网安备 11010802033920号