PLC jog and self-locking circuit I0.1 is the self-locking start button, I0.0 is the self-locking stop button, I0.2 is the jog start button, M0.0 is the intermediate relay, and Q0.0 is the coil output.
When I0.1 is pressed, M0.0 is turned on.
The intermediate relay M0.0 is turned on, its normally open point is closed to form a self-locking state, and its other set of normally open points is closed to connect the contactor coil, and the equipment is powered on and runs.
Press I0.2 for jog, the coil of the intermediate relay M0.1 is energized and closed
When M0.1 is energized, its normally open point closes and connects contactor Q0.0, causing the device to start operating.
When M0.1 is energized, its normally closed point is disconnected, cutting off the self-locking circuit.
Previous article:Analysis of interlocking control circuit of three motors with start-stop sequence requirements
Next article:How to set the parameters of synchronous inverter for multiple motors
- Popular Resources
- Popular amplifiers
- Huawei's Strategic Department Director Gai Gang: The cumulative installed base of open source Euler operating system exceeds 10 million sets
- Analysis of the application of several common contact parts in high-voltage connectors of new energy vehicles
- Wiring harness durability test and contact voltage drop test method
- Sn-doped CuO nanostructure-based ethanol gas sensor for real-time drunk driving detection in vehicles
- Design considerations for automotive battery wiring harness
- Do you know all the various motors commonly used in automotive electronics?
- What are the functions of the Internet of Vehicles? What are the uses and benefits of the Internet of Vehicles?
- Power Inverter - A critical safety system for electric vehicles
- Analysis of the information security mechanism of AUTOSAR, the automotive embedded software framework
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
- Altium Designer single-select and checkbox disproportion
- Help: Transformer detection of low frequency or DC residual current
- [Silicon Labs BG22-EK4108A Bluetooth Development Review] Part 3: Bluetooth-Soc Blinky Example Development Experience
- Analysis of the effect of resistance between the be electrodes of PNP transistors
- I want to do some math questions for the postgraduate entrance examination. Which postgraduate entrance examination tutor can explain the real questions in a detailed and easy-to-understand way?
- Today's live broadcast: TI takes you to experience the interconnected and efficient smart home solutions
- How to scan keys on this triangular keyboard
- How to use CYCLECOUNTER to quickly measure execution time?
- Circuit principle?
- X-NUCLEO-IKS01A3 sensor test based on STM32F401RE development board - STTS751 temperature sensor test