Optimization 2: Load Balancing Management
Optimization 2: Load balancing management
Take battery swap stations as an example. Especially during the Spring Festival, there are many cars waiting in line for battery swapping. It is possible that many cars are connected to one router or WIFI in the battery swap station, while no car is connected to the other one. This results in an unbalanced use of resources. In this case, load balancing can be managed.
Optimization 3: Power Management
Optimization 3: Power Management
As mentioned earlier, there is interference between channels. Ideally, signals should not interfere with each other. This can be done by reducing the overlap of power between channels, thus reducing interference.
4.3 The diagnostic instrument cannot establish a DoIP link
Cause Analysis:
Physical link problem
Data link problem
DoIP activation voltage problem
Peer node DoIP protocol stack implementation issues
Protocol consistency mismatch problem
Logical address definition problem
Other specific issues CASE analysis
Summary: "Look first, ping second, analyze third"
Previous article：Minimizing Noise and Power Consumption in Automotive Audio Systems with SigmaDSP
Next article：What to consider when designing an automotive Ethernet firewall
Recommended ReadingLatest update time:2024-11-16 13:54
- Popular Resources
- Popular amplifiers
Principle and maintenance of automobile on-board network system (CAN-BUS)
- Huawei's Strategic Department Director Gai Gang: The cumulative installed base of open source Euler operating system exceeds 10 million setsOn November 15, the first AI native open source operating system openEuler, openEuler 24 03 LTS version, was officially released on June 6 this year. ...
- Analysis of the application of several common contact parts in high-voltage connectors of new energy vehiclesIntroduction: Connectors are used in every car. The device uses electrical, optical and other signals to control the corresponding mechanical force to connect, disconnect and convert, thereby realizing the corresponding circuit or optical channel conversion. ...
- Wiring harness durability test and contact voltage drop test methodBased on the QC T 29106-2014 standard, this paper proposes a new durability characteristic test and contact voltage drop test method, and conducts experimental verification on these two test methods. ...
- Sn-doped CuO nanostructure-based ethanol gas sensor for real-time drunk driving detection in vehiclesMetal oxides and their composites with other materials (such as MXenes and metal chalcogenides) can be used to achieve different ...
- Design considerations for automotive battery wiring harnessThe battery is one of the power sources of the car. When the generator stops working and the engine is started, all the power is output from the battery. When the engine is idling or working at a low speed, the power generation of the generator cannot meet the demand. ...
- Do you know all the various motors commonly used in automotive electronics?
- What are the functions of the Internet of Vehicles? What are the uses and benefits of the Internet of Vehicles?
- Power Inverter - A critical safety system for electric vehicles
- Analysis of the information security mechanism of AUTOSAR, the automotive embedded software framework
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
- How to choose between different chips in TI's Sub-1GHz product line?
- CircuitPython Electronic Chain Bracelet
- "C Programming Magic Book: Based on C11 Standard"
- [Project Source Code] 3 methods to display state machine names in Modelsim simulation based on FPGA
- Temperature sensor + I2C + serial port + PC host (pyserial) example
- MSP430G2553 internal ADC principle and routine description
- Types of PCB substrates
- What is the difference between an AD schematic and a schematic library?
- Review Weekly Report 20220725: Allwinner 40i development board with 100% domestic components is here, Canaan K510 will be available this Thursday~
- Here is the ultrasound information on the national competition list
京公网安备 11010802033920号