Every day, more and more sensors are added to our daily lives – from smart devices in our homes to increasingly connected vehicles. Real-time sensor data is essential for high-speed data transmission, which requires optimal signal integrity (SI) and electromagnetic compatibility (EMC). To achieve this, you need the right hardware and software equipment and professionals who know how to use these tools.
Continuous testing during product development
Molex optimizes SI/EMC in custom and off-the-shelf products to support connected vehicle and smart vehicle solutions. In order to achieve the required SI/EMC performance, it is necessary to continuously model and simulate the design throughout the product development process. In this way, customers can ensure that their designs have passed rigorous testing and that the final product has the best performance.
SI/EMC Optimization Cycle
Molex's basic SI/EMC process consists of four phases: modeling, simulation, prototyping, and cross-comparison of simulation strategies with empirical measurements. This process and some of the tools used are discussed below.
Previous article：Why does a car’s autonomous driving technology use so many sensors?
Next article：Simplify the design of automotive body motor controllers and quickly achieve lightweighting
- Popular Resources
- Popular amplifiers
-
Computer Vision Applications in Autonomous Vehicles: Methods, Challenges, and Future Directions - 5-port automotive Ethernet switch
- Automotive Electrical and Electronics (Fifth Edition, James D. Halderman)
- Requirements and concepts of future automotive electronic architecture from a comprehensive safety perspective
Computer Vision Applications in Autonomous Vehicles: Methods, Challenges, and Future Directions
- Huawei's Strategic Department Director Gai Gang: The cumulative installed base of open source Euler operating system exceeds 10 million setsOn November 15, the first AI native open source operating system openEuler, openEuler 24 03 LTS version, was officially released on June 6 this year. ...
- Analysis of the application of several common contact parts in high-voltage connectors of new energy vehiclesIntroduction: Connectors are used in every car. The device uses electrical, optical and other signals to control the corresponding mechanical force to connect, disconnect and convert, thereby realizing the corresponding circuit or optical channel conversion. ...
- Wiring harness durability test and contact voltage drop test methodBased on the QC T 29106-2014 standard, this paper proposes a new durability characteristic test and contact voltage drop test method, and conducts experimental verification on these two test methods. ...
- Sn-doped CuO nanostructure-based ethanol gas sensor for real-time drunk driving detection in vehiclesMetal oxides and their composites with other materials (such as MXenes and metal chalcogenides) can be used to achieve different ...
- Design considerations for automotive battery wiring harnessThe battery is one of the power sources of the car. When the generator stops working and the engine is started, all the power is output from the battery. When the engine is idling or working at a low speed, the power generation of the generator cannot meet the demand. ...
- Do you know all the various motors commonly used in automotive electronics?
- What are the functions of the Internet of Vehicles? What are the uses and benefits of the Internet of Vehicles?
- Power Inverter - A critical safety system for electric vehicles
- Analysis of the information security mechanism of AUTOSAR, the automotive embedded software framework
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
- Found a method to import Altium Designer into SIwave
- Thanks to okhxyyo for searching and fish001 for sharing
- Please advise, is it easy to pass the postgraduate examination and graduate, and how useful is the degree certificate?
- About the LAUNCHXL-F28379D Development Kit
- Limited time 1 yuan patch! Save up to 10,000 yuan!
- Let me try this feature
- EEWORLD University-What is a transient voltage suppressor (TVS) diode?
- [Xianji HPM6750 Review] RT-Thread SDIO driver and file system
- FLASH emulation EEPROM experiment
- How can I reduce noise when the signal generator is giving a small signal?
京公网安备 11010802033920号