LED backlight panel shipments continued to increase in Q3 2011, with large-size LED panels accounting for 43% of the total-EEWORLD

Collect

Industry statistics show that due to the lack of orders and the downstream reduction of inventory, there is a situation of oversupply. The shipment volume of large-size LCDs in Q3 2010 decreased by 4% compared with Q2, and increased by 7% compared with the same period in 2009, reaching about 163 million pieces. However, the shipment volume of LED backlight module panels continues to grow.

Due to the increase in special deals reached by brand manufacturers for low-cost solutions for promotional models in the peak sales season at the end of 2010, the shipment volume of LCD TV panels in Q3 continued to rise, especially for models larger than 40 inches and LED backlight models. The shipment volume of LCD panels with a size of 40 inches and above reached 18.1 million pieces, an increase of 13% over Q21; among them, the shipment volume of LED backlight panels reached 7.8 million pieces, accounting for 43%, an increase of 2 million pieces over Q2.

Keywords：LED Reference address：LED backlight panel shipments continued to increase in Q3 2011, with large-size LED panels accounting for 43% of the total

Previous article：LED driver chip design and detailed explanation
Next article：Detailed explanation of the basic knowledge and characteristics of LED display

Recommended ReadingLatest update time:2024-11-16 21:25

Comparison between LED COB packaging and traditional packaging

From the perspective of LED packaging development, LEDs have two packaging forms: discrete and integrated. LED discrete devices belong to the traditional packaging form and are widely used in various related fields. After nearly 40 years of development, a series of mainstream product forms have been

[Power Management]

Comparison between LED COB packaging and traditional packaging

Design of 6A Step-Down LED Driver Based on MAX16821

This reference design is for a 6A buck LED driver for portable projectors. The reference design is based on the MAX16821 PWM HB LED driver. This circuit can drive one LED; three MAX16821s are required to drive RGB LEDs. LED Driver Specifications Input voltage range (VIN): 10V to 15V Outp

[Power Management]

Design of 6A Step-Down LED Driver Based on MAX16821

High-efficiency LED driving mode realizes ideal LED lighting equipment

In today's society, the differentiation of lighting environment requirements of various media devices has further promoted human exploration of how to use various high-brightness LEDs for lighting. The application of LEDs in lighting has attracted widespread attention. LED basic principles and performance chara

[Power Management]

High-efficiency LED driving mode realizes ideal LED lighting equipment

51 single chip microcomputer LCD1602 display

Pin Diagram #include reg52.h #include intrins.h #define uchar unsigned char #define uint unsigned int #define out P0 sbit RS=P2^7; sbit RW=P2^6; sbit E=P2^5; void lcd_initial(void); //LCD initialization function void check_busy(void); //Check if it is busy function void write_command(uchar com); //write comma

[Microcontroller]

51 single chip microcomputer LCD1602 display

Mini2440 bare metal test - button control buzzer and LED

According to the user manual and data sheet *************************************************************************************************************************************************************** **********************************************************************************

[Microcontroller]

Mini2440 bare metal test - button control buzzer and LED

Design of LED rotating screen based on AVR

0 Introduction With the rapid development of computers and related microelectronics and optoelectronics technologies, LED display screens have become a new type of electronic screen advertising media. Compared with traditional inkjet and photo-based advertising images, which are rigid and inactive billboards and adve

[Microcontroller]

Design of LED rotating screen based on AVR

Why does white light LED need to be split and color separated?

Why does white light LED need to be split and separated into colors? White LED lamps must be spectroscopically separated before leaving the factory (some LEDs that have not been spectroscopically separated emit pure white light, some are bluish, and some are yellowish). Spectroscopic separation instruments ar

[Power Management]

Design of large-screen LED dot matrix display system based on FPGA

LED screens have appeared as early as the 1960s, but full-color screens did not appear until the mid-1990s. The price of this technology has dropped significantly in recent years, and the resolution has also improved significantly. For video, the low-resolution performance of LED screens is good. The resolution of L

[Analog Electronics]

Popular Resources
Popular amplifiers