●Try to use original batteries
Using original batteries is the most important thing to ensure your safety. Nokia once claimed that there have been more than 20 mobile phone battery explosions in the past few years, and none of these explosions were caused by original batteries. It can be seen that the safety of batteries provided by third parties is very low, so try not to use third-party batteries. If you have to use them, try to choose third-party batteries with a good brand reputation.
●Do not use damaged batteries
A damaged battery is very likely to explode. Even if it does not explode, it can damage the phone and cause a short circuit in the phone's internal components, so do not use a damaged battery.
●Use the original charger as much as possible
The original charger can ensure the safety of the battery. Although compatible chargers can also be used, some of them may damage the battery and cause explosion due to electrical failure.
●Don’t modify your phone at will
Improper modification of mobile phones can easily cause them to explode. Mobile phones are sophisticated communication devices. When they are designed, manufacturers will conduct strict safety tests and their electrical performance is the best. However, after modification, all of this will change, which can easily cause the phone to explode.
●Do not place the battery in a high temperature environment
High temperature will cause the battery to heat up, which can easily cause an explosion. Therefore, when charging the battery or placing the phone, be sure to choose a place away from high temperatures and avoid direct sunlight in the summer.
Mobile phone calls and placement
●Don’t talk on the phone for long periods of time
Long-term calls will not only heat up the phone battery, but also the internal circuit and receiver of the phone. If you happen to use a fake battery, it is very likely to cause an explosion.
●Try not to make phone calls while charging
When charging, the mobile phone battery will generate heat. If we continue to use it to make calls, the heat will increase rapidly and it can easily cause danger.
● Use headphones to answer calls, preferably Bluetooth headphones
Answering calls with headphones can reduce radiation and avoid facial injuries caused by mobile phone explosions. Bluetooth headphones are recommended because they are wireless and safer.
●Try to keep your phone in your bag
Putting your phone in your bag can reduce the chance of losing it and prevent the direct harm of explosion to the human body. It is best not to put your phone in your jeans pocket, as it will be difficult to take it out in case of danger.
●Don't hang the phone on your chest
It is definitely not a wise idea to hang your phone on your chest. If the phone suddenly explodes, it will directly injure your chest and face. In addition, this also increases the chance of losing your phone.
There are usually several ways to charge a mobile phone: direct charging, travel charging, and dock charging. Among them, direct charging (wired charging) is a safe and reliable charging method that has no adverse effects on battery life; dock charging is used to charge another battery during the use of the mobile phone. It needs to be connected to the original charger (wired charging) and is the safest and most reliable method; travel charging and universal charging use low-cost circuits and components to achieve wire charging and dock charging functions at the same time, and overvoltage and overcharging protection is very difficult, so this charging method is not recommended.
Previous article:Inside a fake iPhone charger: The smaller, the more dangerous?!
Next article:Design of power management system for smart phone
- Popular Resources
- Popular amplifiers
- MathWorks and NXP Collaborate to Launch Model-Based Design Toolbox for Battery Management Systems
- STMicroelectronics' advanced galvanically isolated gate driver STGAP3S provides flexible protection for IGBTs and SiC MOSFETs
- New diaphragm-free solid-state lithium battery technology is launched: the distance between the positive and negative electrodes is less than 0.000001 meters
- [“Source” Observe the Autumn Series] Application and testing of the next generation of semiconductor gallium oxide device photodetectors
- 采用自主设计封装,绝缘电阻显著提高!ROHM开发出更高电压xEV系统的SiC肖特基势垒二极管
- Will GaN replace SiC? PI's disruptive 1700V InnoMux2 is here to demonstrate
- From Isolation to the Third and a Half Generation: Understanding Naxinwei's Gate Driver IC in One Article
- The appeal of 48 V technology: importance, benefits and key factors in system-level applications
- Important breakthrough in recycling of used lithium-ion batteries
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
- Design and implementation of a miniature real-time multi-eye stereo vision machine
- program
- [Today at 10:00 am] Keysight metrology experts talk about: Electronic instrument metrology calibration knowledge and calibration cycle
- Innovative power supply questions - Analysis of 2019 National Power Equipment A Question
- bq4050 power jump
- EEWORLD University Hall----Using MATLAB for FPGA Design
- Why should computer science students learn to use Linux systems?
- EEWORLD University Hall----Live Replay: Secure Boot of Microprocessors
- Texas Instruments Action Camera and Handheld Gimbal Solutions
- Reading Notes on the Good Book "Operational Amplifier Parameter Analysis and LTspice Application Simulation" 05--LTspice Simulation