Based on STC15W2K60S2 FFT-IFFT program, hardware test passed

Recommended ContentMore

Open source project More

• Fingerprint sending
• Battery power management chip SY6982EQDC evaluation board
• Super mini UART tool
• Intelligent medicine delivery car (Question F)
• FP5139 buck-boost module
• Arduino Nano schematic
• Simple circuit to detect mobile phones
• Lichuang EDA touch night light
• PCB Physical Bookmark_Version 1
• NCV890430MW50GEVB: 2 MHz, 100% Duty Cycle, Buck Synchronous Regulator Automotive Evaluation Board

Searched by Users

• Altium Designer schematic library commonly used component library.SCHLIB
• Wireless network card driver 5.1279 XP general version_xp
• Spark official document Chinese version.pdf
• Download pdf of Matlab basic tutorial
• Proteus7.8 Chinese patch
• Source code (Verilog) of Master SPI, including documentation, test program
• Pressure Pipeline Installation Permit Rules TSG D3001-2009
• STM32F4 Chinese Manual
• Read the manufacturer ID and chip ID of FLASH-Read the manufacturer ID and chip ID of FLASH
• Implementation of color settings, sliders, list boxes and other controls under Matlab

Just Take a LookMore

• pwm
  What is the difference between these two PWMs? Is it a transistor speed control?
• Power supply - Does the P tube of this TL431 voltage regulator circuit need to consider the problem of power supply short circuit to ground when it is turned on?
  The output voltage rises, the cathode voltage of TL431 drops, the P tube is turned on, and the output voltage drops. But doesn't the transistor go directly to the ground when it is turned on? Is there
• Online door lock system consultation
  Is there anyone in the forum who has used it or has relevant development experience, and would like to cooperate on a project?
• [AB32VG1 development board review] PWM adjustment and breathing light
  [i=s]This post was last edited by jinglixixi on 2021-9-13 17:09[/i]AB32VG1 is equipped with 6 PWM output channels. If PWM is used to control RGB_LED, a breathing light effect can be produced. The pin
• Flashing Lights
  Here is a flashing light experiment procedure for everyone As shown in the figure below: Connect a light-emitting diode L1 to the P1.0 port , so that L1 is constantly on and off. 2.Circuit diagram　Fig
• KEILC51 embedded assembly method
• Micron's New Year's Lucky JD E-Card is waiting for you to draw
• About JLink automatic firmware update problem
• On the feasibility of the traditional brake transformation of stepper motor
• Isolated Buck Converter PCB Layout Tips

Trending Downloads

• A new threshold method
• 51 Control MPU6050
• A complete version of the operating system experiment report for the third year
• ThreadPro is a Delphi basic class library developed by me for multi-threaded programming
• The software and hardware interface between PS2 mouse and 51 series single chip microcomputer
• Dual power automatic transfer switch
• I want to load down some project
• Serial terminal (Win10 64-bit available, tested)
• LL(1) grammar implementation code
• Oppenheim\'s \"Signals and Systems\" and exercises and answers

Trending ArticlesMore

• Zero-shot learning surpasses CLIP! Google proposes the first multimodal sparse model LIMoE, which can also reduce computational costs
• Campus Recruitment | Welcome to the era of invention, Qualcomm 2020 campus recruitment is officially launched!
• Award-winning live broadcast | ADI digital active noise reduction headphone solution, let technology calm us down
• Rohde & Schwarz supports growth of naval intelligence and surveillance capabilities
• Broadcom officially acquires CA, selling its Veracode business for $950 million
• AWorks Software - In-depth understanding of AWbus-lite (basic concepts of device drivers)
• Tsinghua Unigroup 8GB DDR4 memory sticks are now on sale! The particles are mysterious and unknown
• In the digital healthcare era, wireless medical coexistence test solutions directly address the "pain points"
• Whole-retail cooperation leads to a win-win future