Discussion on debugging methods of medical imaging display

Recommended ContentMore

Open source project More

• Ebyte E18 series Zigbee product test board
• Portable wireless touch remote control
• LM2596
• Based on Tuya Smart, realize Internet of Things temperature and humidity sensor
• Angle data acquisition module based on Lichuang Liangshan School
• OM40001: LPCXpresso804 for LPC804 series MCUs
• stm32 oscilloscope
• Discovery board for the ST25TV02KC NFC Forum Type 5 tag IC
• LS1021A-IoT gateway reference design
• 1.57 inch ips touch screen 320x360 spi CGHAX157-010

Searched by Users

• SM2213EA 14W9V dimming color adjustment high voltage linear led constant current driver chip 2
• linux-api manual
• MTK flashtool
• MPLAB 5.70.40 Free Download
• Graphical Oscilloscope Usage and Application Techniques 286 pages 49.2M Bookmark Version.pdf
• AD\'s most complete package library
• Cadence Allegro PCB Design 16.2 Download
• Decoder, priority decoder
• Bluetooth headset PCBA, Bluetooth module PCBA using PADS2005 drawing board
• Aixin Yuanzhi-AX630A Development Board Data Sheet

Just Take a LookMore

• The actual output voltage of the SEPIC circuit does not match the theoretical value.
  As shown in the figure, Vin input is 7~12V; R3=9k ohm, R6=1K ohm;power chip XL6008 (Xinlong), FB pin voltage VFB=1.25. (Measured VFB=1.248V);theoretical output Vo=(1+R3/R6)*1.25=12.5V, but the measure
• Transistor push-pull output circuit
  I would like to ask, after adding two diodes to compensate for this push-pull output circuit, a slight phase shift occurs. How can I solve this problem?
• Sharing of national competition experience
  I participated in electronic design competitions when I was in school, but I didn't get any results. Later, I led a team to participate in several competitions after I started working. Overall, my exp
• Testing the Kalman Filter
  The real temperature test data is measured by heating a basin of water with a heating rod. The X-axis is time in seconds and the Y-axis is temperature: 1) Before filtering2) After filtering (p=10, q=0
• Ltspice .save
  During simulation, a lot of data is often generated. Some data is useful to us, while some data is just auxiliary and we will not look at it. So how can we ensure that the simulation software only sav
• SinlinxA33 development board uses MIPI DSI screen
• Install Runhe Neptune Hongmeng system on w801kit
• DSPC6678 on-chip storage space allocation mechanism
• Ask a silly question about f_mount()!
• [Evaluation of SGP40] + Cloud platform configuration for IoT remote monitoring application development

Trending Downloads

• Design of Embedded USB Host in ARM and LINUX Systems
• for_deci_spl
• XTR112,XTR114,pdf(4-20mA Curre
• 100Hz trap circuit experiment 13
• Audio power amplifier characteristic test system based on LABVIEW
• gsm&gprs terminal test v5
• ADS6444,pdf (QUAD CHANNEL, 125/105/80/65 MSPS ADC WITH SERIAL LVDS OUTPUTS )
• Introduction to Passive Electronic Components
• Design of stepper motor drive system based on 89C2051
• Design and extension research of MCS51IP core based on EAD technology

Trending ArticlesMore

• Easter Egg丨This is an invitation letter, please check it (don’t miss the Easter Egg inside)
• “Not inferior to GPT-4”! Baidu’s most powerful model was released, and we tested it for the first time
• Infineon Technologies provides secure and convenient mobility solutions for smart cities
• Is demand reaching a turning point? 70% of Taiwan's top 10 semiconductor companies have seen a decline in performance
• A 6.1-magnitude earthquake occurred in Taiwan, and semiconductor companies responded
• MOTO G5 released, what did Lenovo get for $2.9 billion? 丨MWC 2017
• List of the largest domestic chip companies
• The official arrival of the wireless communication era
• Jen-Hsun Huang: If I could go back to 30 years old, I would not start Nvidia
• How to quickly get rid of the "technical newbie" hat - teach you how to play with the RZ microprocessor series in five days · STEP 5