The reading and writing of X5045 under PHILIPS MCU P89C668 can be transplanted to MCU with 51 core after debugging.

Recommended ContentMore

Open source project More

• #The 7th Lichuang Electric Competition#Current and voltage table
• stm32f429 mini version 4G IoT development board
• wz-sk-art-pi-module
• Guanye f437mini (not verified)
• 【ART-Pi】Target Stars and Sea: A Car with Infinite Possibilities-402304A
• R_74_V10 Design based on IPS2 motor commutation sensor
• Intelligent bedroom system based on Liangshan School
• Switching power supply design based on STC12C5A60S2
• Microcontroller learning board based on STC8A8K64S4A12
• ic/id/bingdundunxuerongrong

Searched by Users

• CAXA Electronic Drawing XPR2 Download
• Arduino Technical Guide.pdf
• Huawei PCB EMC Design Guide
• GB 13511.1-2011 Fitted spectacles Part 1: Single vision and multifocal.pdf
• USB Serial Converter driverUSB serial port driver
• Optimization method and its MATLAB implementation (Xu Guogen)
• Technical Guide for Developing USB Device Control Using NI VISA Driver
• Brave Core helps you play with Xilinx FPGA
• Renesas MCU Download Software
• Renesas MCU Download Software

Just Take a LookMore

• Why does the AD21 shortcut key not work after modification?
  AD21 I changed the * key for drilling holes during wiring to 4. There is no conflict with other shortcut keys, but it does not work after the modification. When I press 4 during wiring, the hole will
• Design of high-power laser power supply based on MAX1647
  1 Introduction 　　With the continuous development of diode-pumped all-solid-state laser related technologies, it is more and more widely used in the fields of industry, national defense research, biome
• [ESP32-Audio-Kit Audio Development Board Review] Basic Use of the Development Board
  [i=s]This post was last edited by jinglixixi on 2021-9-25 10:12[/i]On the ESP32-Audio-Kit audio development board, the most basic peripherals are LED and KEY, and their schematic diagram is shown in F
• Can the SSTX and SSRX of USB3.0 be identified and adjusted? Is it necessary to cross it when making a schematic diagram?
  Can the SSTX and SSRX of USB3.0 be identified and adjusted? Is it necessary to cross-process when making a schematic diagram?
• Four advantages and applicable fields of LoRaWAN
  With the rapid development of communication technology, the communication industry is about to enter the 5G era. Data transmission will be more intensive, and the amount of data exchange will become l
• "Playing with the board" + ADC experiment based on STM32F030Disco
• [New Year's Flavor Competition] + New Year's Eve dinner, visit lanterns, live a wonderful life!
• How to solve the problem of PCB circuit board via blockage
• The multimeter burned up, the cow dung chip exploded, I took it apart and replaced it with a hard seal, and I actually fixed it!
• Review the basics of static electricity control

Trending Downloads

• DSP28335 Tutorial
• Journal article: Research on beam crack identification based on wavelet analysis
• ModbusV1.024 (Modbus Debug Wizard - Debugging Tool
• LCD driver program based on SPMC75F2413A
• Advanced Rf Tool Calculation Software
• Daily maintenance of DWDM optical transmission system
• Design and Application of an Uniform Identity Authentication System for Building a Knowledge Sharing Platform
• Design of DeviceNet Interface Circuit in Industrial Temperature Control System
• Impedance in design, see the forum everywhere asking for money to post
• BISS0001.pdf

Trending ArticlesMore

• [Solution Selection] Black technology for extreme signal environments! WPG launches text information transmission solution based on Semtech and Huantianshitong products
• Watch the video to win a 50-yuan Jingdong card | Taixiang's actual test of Shui Ge's secrets, the fourth issue
• Samsung is "determined" and Apple loses!
• 2017 Renesas Cup National Undergraduate Electronic Design Competition kicks off
• Why choose AMD Radeon Pro workstation graphics cards?
• Grand opening pictures are coming: promise to China, promise to the future
• Highlight the key points! You must understand the new multi-processor cluster architecture!
• Infineon Technologies Launches XENSIV™ TLE4972, a High-Precision Coreless Current Sensor for Automotive Applications
• Bluetooth Mesh Design Lecture (Part 3): Privacy and Security
• PIC32MM series 32-bit microcontroller