Parallel port communication technology under real-time operating system VxWorks

Recommended ContentMore

Open source project More

• [Hangshun Training Camp] Hangshun Core Board +431100W
• STLM20 based temperature probe kit
• 【Training Camp】RGB Small Lamp-996120A
• Protues simulation example (8051)-PWM wave output (adjustable)
• [Complete Design] Heart rate and blood pressure watch based on STM32
• Euclid Klicky Probe pcb
• 【RA】Flowing water lamp
• 43 W high power factor constant voltage output flyback converter based on ICL8820
• ESP32-SOLO
• Four-way answering system

Searched by Users

• Serial port debugging assistant VNC-Viewer-5.0.0-Windows-32bit
• Modelsim+DSP_builder crack
• PCB3D Footprint Library
• FANUCLADDER3V5.7 software
• Download the latest proteus component library
• C Traps and Pitfalls (pdf Chinese version) Download
• Packet Tool (Latest Version)
• Technical data: All transformer frame specifications and dimensions
• LP2801 Chinese Data Sheet
• Ahaha C language - programming basics

Just Take a LookMore

• FPGA Design Process
  FPGA Design Process
• Power supply obstacles + power supply SBC selection and pitfalls
  Hello everyone, I am an automotive electronics hardware engineer. When selecting a power SBC, you should pay attention to the battery voltage range and then combine it with the test standards to selec
• Sharing of key points on the use of ADI passive components
  Sharing of key points on the use of ADI passive components
• Four design considerations for telematics hardware in connected cars
  It may surprise you to learn that a technology that has been around for nearly two decades has paved the way for connected cars. ECall is old fashioned by high-tech standards, but it is now mandatory
• Wide voltage input USB-C, 5V/3A output adapter reference design
  USB-C, DFP, 5V/3A output, 85-265VAC input, adapter, low cost reference designThe UCC28700 and TPS25810 are used to provide isolated 5 V at 3 A over the USB type C interface. The UCC28700 performs prim
• When the machine is turned off, the LDO output is normally 3V. Why does the voltage reach 3.5V after the machine is turned on? What is the reason?
• 【Smart Sports Watch】3. Build Development Environment 2
• Ginkgo USB-SPI host mode four data transmission mode timing diagram
• History of the Development of Microwave Circuits
• 6657Statically configure serial port general interrupt in sys/bios

Trending Downloads

• Combined converter circuit
• Design and implementation of a network virtual experiment system for controlling three-phase asynchronous motors
• High-speed interface interconnect
• Design of digital controlled DC current source based on single chip microcomputer control
• Using D12 to implement the single chip microcomputer program of USB disk
• In-depth analysis of variable declaration and definition in C C++
• Journal article: Remote sensing image recognition and data conversion for flood monitoring
• APl431Lb7
• Bus voice automatic station announcement system based on single chip microcomputer
• Failure Mode Analysis of Fiber Optic Splitter Reliability Test

Trending ArticlesMore

• The registration gate is down! The monopoly app angered 700,000 art exam candidates, and buying the 589 yuan VIP channel was in vain
• Report | Murata's views on the high-power battery cell market
• Add emergency LED to mini mobile power supply yourself
• Python implements a "bird face recognition" system to see which bird is the most greedy ~ Beginners can also learn it
• TSMC shares six key points: 2nm will arrive in 2025
• Secretly tell you how I use the AI ​​large model to move bricks for me!
• Get a gift! Security innovation, a new verification method Download Fujitsu's "Spectrum Verification Solution" white paper
• How to make home appliance motors more energy-efficient and reduce emissions? Infineon PSoC™ has an unshirkable responsibility!
• Video: PolarFire® SoC Series 3 – Restoring Factory Defaults
• Product Recommendations | SiC MOSFET packaging, system performance and applications