Detailed explanation of WCDMA terminal cell search process

Recommended ContentMore

Open source project More

• 15V Walkman 1
• Based on the Lichuang Liangshan School - "Patch the numbers together" smart car
• 555 flashing light
• GN1621 Broken Code LCD Experiment Module#
• Audio amplifier V1.2
• Tuya IoT infrared voice assistant
• Elrs_Rx_1.1
• Ormerod Mini Differential IR Sensor
• STLink V2.1/DAPLink with DC-DC power supply
• LED full color dot matrix screen driver board

Searched by Users

• Pro ENGINEER Wildfire v4.0 Download
• High-speed MOS driver circuit design and application guide
• Commonly used numerical algorithms and programs in computers (C++ version) Chap06 Matrix eigenvalue and eigenvector calculation
• CST Antenna Simulation and Engineering Design [Jin Mingtao] 2014 Edition
• C Programming: A Modern Approach: 2nd Edition.pdf
• CANopen Source Code
• 51 MCU download program steps
• Siemens S7-1200PLC
• Mitsubishi full range PLC programming manual
• Let\'s learn Cadence Allegro high-speed PCB design (Li Wenqing)

Just Take a LookMore

• IRLR024 Output Current
  A 100W/200R cement resistor is connected to the J14 load. I checked the power meter and found that the load power is less than 1W. The voltage given by PC6 is 3.3V. The meter shows that there is a cur
• Bidirectional thyristor circuit wiring problem
  As shown in the figure, the wiring method of the bidirectional thyristor in the circuit is that because it is bidirectional, I swapped T2 and T1. The thyristor was always in the on state and could not
• "Goodbye 2019, Hello 2020" + The wind and clouds are free and happy
  First of all, I wish you all a happy Chinese New Year. This year can actually be described as "turbulent". Electronic technology and chips have become the top search terms in 2019. Every fluctuation i
• A simple question for help
  How to use NE555 to build a square wave signal with a duty cycle of 50%, a signal amplitude of -5V~+5V, and an adjustable frequency (1khz~50khz). I have only learned the basics of circuit analysis and
• The power problem of the series resistance of the atomizer heating wire
  As shown in the picture, the actual boost voltage of the ME2139 DC-DC boost IC I used is 4.8V, and the current it can withstand is 2.5A. There is a series heating wire (2.5R) in the COIL, and I connec
• [GD32F310 Review] Interrupt test and GPIO usage
• As a newcomer, I don't seem to be qualified to make suggestions, but I still want to make a small suggestion!
• The DTK28335 experimental box chip is very hot
• Have you ever used a fast charger using gallium nitride (GaN) technology?
• [HPM-DIY] HPM6750 peripheral LCDC driver RGB screen high frame rate video playback

Trending Downloads

• Hi-Fi three-way active crossover
• Skype network traffic measurement and feature discovery
• Ultrasonic technology and its application 200 pages 3.0M.pdf
• A Socket connection class
• BF518 reads the keyboard decoding chip program
• Research on attitude estimation and control algorithm of quadrotor aircraft based on Kalman filter
• ROHM AC/DC Designer User\'s Guide
• DM74LS293
• 6561 and L5991 form an adapter with standby function
• SKYWORTH LCD 8DA2 movement maintenance manual

Trending ArticlesMore

• Easter Egg丨This is an invitation letter, please check it (don’t miss the Easter Egg inside)
• “Not inferior to GPT-4”! Baidu’s most powerful model was released, and we tested it for the first time
• Infineon Technologies provides secure and convenient mobility solutions for smart cities
• Is demand reaching a turning point? 70% of Taiwan's top 10 semiconductor companies have seen a decline in performance
• A 6.1-magnitude earthquake occurred in Taiwan, and semiconductor companies responded
• MOTO G5 released, what did Lenovo get for $2.9 billion? 丨MWC 2017
• List of the largest domestic chip companies
• The official arrival of the wireless communication era
• Jen-Hsun Huang: If I could go back to 30 years old, I would not start Nvidia
• How to quickly get rid of the "technical newbie" hat - teach you how to play with the RZ microprocessor series in five days · STEP 5