Altium 15 latest device library: Johanson Technology (Legacy).rar

Recommended ContentMore

Open source project More

• USB to TTL module
• MPC837XEMDS: MPC837xE Modular Development System
• Type-C Tai Chi Night Light [Low Cost]
• SimpleLink™ CC32xx-OV788 Reference Design for Video/Audio Streaming over Wi-Fi
• DI-29 - 25 W Flyback DC-DC Converter
• IP6518 step-down QC3.0 multi-protocol fast charging module
• 【CW32】Tianshu big drill bit (electric hand drill)
• MINI-PCIE to Gigabit network card RTL8111E/F
• baby monitor
• Ultra-portable, low-power nHD display reference design for low-cost processors using TI DLP® technology

Searched by Users

• STM32F407 drives EC20 module MCU source code, for your reference
• C language C++ resource download
• Lichuang Mall Standard Library-ad16 Version
• Switching Power Supply Design 3rd Edition
• Capacitor Handbook
• LaunchPad Pocket Experiment Platform—MSP-EXP430G2
• vc knowledge base
• Download the complete set of materials for making your own ICD2-USB (schematic diagram + PCB + program)
• MATLAB Speech Signal Analysis and Synthesis 2nd Edition (Song Zhiyong)
• Zhongke Microelectronics GPS module data + debugging software tools + V3.1

Just Take a LookMore

• msp clock setting program
  In 430, one clock cycle = the inverse of the MCLK crystal oscillator. If MCLK is 8M, then one clock cycle is 1/8us;one machine cycle = one clock cycle, that is, each action of 430 can complete a basic
• Parameters of terminal blocks
  As shown in the figure below, the terminal block is a double-layer pluggable terminal block What does the number of positions in the red box in the picture mean? It looks like there are 20 interfaces
• Inverter output filter inductor
  Inverter output filter inductor The design of the inverter output filter inductor first needs to determine its LC value according to the control, and then design it on this basis. Generally speaking,
• Transistor replacement
  Everyone, what can I use to replace the N tube KTC4373, SOT-89 package? Urgent
• MATLAB/Simulink Video Tutorials
  Nowadays, many automotive ECU software development uses MATLAB modeling, which is much easier and more time-consuming than writing code before. I’m posting this here for everyone to learn from.
• NEX
• C Basic skills training
• Discussion: How many spacings should be used to drill a GND via in RF high-speed PCB design? [Repost]
• What are the precautions for using variable frequency power supply?
• Qorvo frequently promotes 5G and releases chips to make headlines?

Trending Downloads

• Application of Synchronous Rectification in WK283R3S-33M
• iccavr v6.31a crack version download
• Journal article: Segmentation of color images using Gaussian mixture model and EM algorithm
• Power management chip OZ992v1_7
• SN75LP1185,pdf(Low-Power Multiple RS-232 Drivers And Receivers)
• Design of 2D Barcode Recognition System Based on NiosⅡ
• Help you quickly master zigbee wireless technology
• FBs-7SB module settings and operation instructions
• keilc51 0xfd patch verification program SCAN.C(338): warning C280: UpLoadReady : unreferenced label
• Improvement of ECDSA algorithm and selection of scalar multiplication

Trending ArticlesMore

• Easter Egg丨This is an invitation letter, please check it (don’t miss the Easter Egg inside)
• “Not inferior to GPT-4”! Baidu’s most powerful model was released, and we tested it for the first time
• Infineon Technologies provides secure and convenient mobility solutions for smart cities
• Is demand reaching a turning point? 70% of Taiwan's top 10 semiconductor companies have seen a decline in performance
• A 6.1-magnitude earthquake occurred in Taiwan, and semiconductor companies responded
• MOTO G5 released, what did Lenovo get for $2.9 billion? 丨MWC 2017
• List of the largest domestic chip companies
• The official arrival of the wireless communication era
• Jen-Hsun Huang: If I could go back to 30 years old, I would not start Nvidia
• How to quickly get rid of the "technical newbie" hat - teach you how to play with the RZ microprocessor series in five days · STEP 5