protel99se-Micro Control

Recommended ContentMore

Open source project More

• ADC_TEMP_HUMI
• CN0172
• C5157210_WM8960 audio driver solution verification board
• (Verified) High-power LED constant current driver based on MP24894
• PCB WIFI directional antenna
• 【Training Camp】IoT Clock +955390A
• Digital and Electronics Course Design
• Arknights Rhode Island theme decorative lamp touch adjustment USB power supply 8022W
• KITFS84SKTEVM: FS84 QFN48EP Safety SBC programming board
• 【Training Camp】Lamp

Searched by Users

• PCB copper skin current capacity calculation software
• MT5931_Data_Sheet_v0_12.pdf
• Vivado Starts Here
• Self-made package library: QFN40-6x6
• Learn C++ in 21 days (4th edition).pdf
• Modbus, Modbustcp master station test tool
• 104 protocol master library source code
• Electronic textbook: Circuits and Analog Electronics Technology.pdf
• Automotive Electronics Product Reliability Test Standards
• Agilent ADS Communications System Design Simulation Software

Just Take a LookMore

• The power cord is too long and the power-on voltage is too high. Should I use a TVS tube?
  I have a question. The circuit board has an external 5V input. The power line is too long, 3 meters. The voltage is too high when it is powered on. Should I use a TVS tube? Or add a filter capacitor?
• What is the essence of GND in the circuit?
  Ask a simple but difficult to answer circuit question: What is the nature of the ground wire GND in the circuit?During the PCB Layout process, engineers will face different GND treatments.Why is this?
• EEWORLD University - i.MX Linux Development Practical Guide
  i.MX Linux Development Practical Guide : https://training.eeworld.com.cn/course/5854The first issue - Getting Started with Zero Foundation - 47 episodes The second issue - Kernel Programming - 20 epis
• Encoder Problems
  [backcolor=rgb(222, 240, 251)]I designed an encoder circuit, the circuit is as follows: [/backcolor][backcolor=rgb(222, 240, 251)]Afterwards, when I turned the encoder, there were waveforms on both en
• A zero voltage platform appears on the secondary side of the forward converter, causing large oscillations. What might be the cause? How can I solve it?
  I'm working on a forward converter recently, using RCD for excitation reset, and it's basically working normally. However, when the MOS tube is turned on and off, there is a commutation process betwee
• STM32MP157A-DK1 Review - 5.10 minutes to create a Linux Distro
• DIY a ESP32 game console based on MicroPython
• Getting started with BIT_BAND (bit segment/bit band) and alias area in STM32
• [Xianji HPM6750 Review] RT-Thread SPI Driver and WiFi Networking
• In-depth analysis of the design of a dental chair control system based on ARM embedded technology

Trending Downloads

• DS1233M
• Journal article: Adaptive beam pruning for speech recognition
• Logic circuits made of discrete components
• Msp430_G2553 series core information
• 74VHC4040
• Quartus+II+ debugging Error and Warning and solutions
• Constant Current Adjustable 0.7 A to 1.5 A to 55 Vdc Single Stage Power Factor Corrected LED Power Supply
• Electrical schematic diagram of Little Swan automatic washing machine XPD-180-4
• 74VCX162244
• Self-made 3D component library: SW-KCD1-102.SLDPRT

Trending ArticlesMore

• Amplifier input impedance parameters and application simulation
• Run, wireless charging!
• Did Intel really lose?
• [Chongqing Station] Registration for Melexis Sensing Technology Tour Seminar is now open!
• common problem
• Apple's most ambitious chip plan yet
• Summary of the Semiconductor Equipment Market in 2020
• ​ADI & Shijian will help you understand chemical analysis and analytical instrument application solutions. Answer questions and win prizes!