Demonstration video of intelligent cigarette cabinet management system based on Lichee Pi 4A

Recommended ContentMore

Open source project More

• XL4005 aluminum substrate
• DI-91 - 12W Universal Input CV Adapter
• C2985579_ZigBee module verification board based on ZTLC5
• Industrial digital output expansion board based on IPS160HF, suitable for STM32 Nucleo
• Ceramic LED digital tube base
• NCP115AMX120TCGEVB: NCP115: LDO Regulator, 300 mA, Low Iq, High PSRR, High Accuracy Evaluation Board
• #The5thLichuangElectronicDesignContest#baizhuobanxia
• DI-31 - 5 V, 70 W DC-DC converter with synchronous rectification
• DER-815 - 45W 24V output isolated flyback power supply for smart speakers and tubular motors based on InnoSwitch3-CP
• S08PT60-EVK: Evaluation kit for S08P MCUs

Searched by Users

• Tsinghua Sweil calculation cracking, used for feudal and installation 2008
• High-speed MOS driver circuit design and application guide
• Dual-band wireless router print server client software
• How to output SMT coordinate files from PADs
• Punctual Atom Pioneer Project Source Code
• MATLAB Hilbert transform envelope spectrum source code
• Overview of WinCC Common C Language Scripts
• Matlab program toolkit
• STM32 virtual oscilloscope lower computer program source code (keil project)
• Zhejiang University Supcon DCS system software training materials

Just Take a LookMore

• STM32L151RCT6 cannot enter low power after downloading the program
  Hello everyone, I encountered a strange problem when using the STM32L151RCT6 microcontroller. I used the HAL library. After I downloaded the program, if I did not completely cut off the power, the mic
• The CC2541 is connected to the Bluetooth module, but the Bluetooth module cannot receive the data it sends.
  I use CC2541 to communicate with Bluetooth module DS-BT19-S Bluetooth module. Now it is connected, but the CC2541 sends data and the Bluetooth module cannot receive it. Use the mobile phone LIGHTBLUE
• Set the maximum FM bandwidth to 4GHZ
  [i=s]This post was last edited by Not Just a Passerby on 2022-1-12 16:55[/i]How to set the maximum FM bandwidth 4GHZ in the CFG configuration file in TI millimeter wave radar
• Selection of digital input chips such as liquid level switches
  Dear experts, I would like to ask, for digital quantity input into the single-chip microcomputer, are there any chips available, such as liquid level switches, 24V, there are 5, I want to connect to t
• 【NXP Rapid IoT Review】+ Unboxing Review
  [i=s]This post was last edited by decade_0809 on 2019-1-2 22:49[/i] [b][color=#5e7384]After receiving the development board, I unpacked it and found that it only came with a data cable, a development
• Research and exploration of unmanned vehicle terminal control
• micrpython
• What are the advantages of AT32F413 replacing STM32F103?
• DSP GPIO input and output settings
• TMS320C665x]02, CCS v6.1 Full License Harmony

Trending Downloads

• Introduction to the i2c bus
• xStart Series Motor Control and Protection - Selection Guide
• Design of dimming controller based on single chip microcomputer
• Infrared remote control software decoding principle and procedure 1 Infrared starts to send a 13.5ms guide code
• dmx512 circuit diagram.rar
• CXD2498R.pdf
• 51 MCU DS18B20 digital temperature
• A detailed introduction of usbcore in linux by an expert
• MW3820 Command Manual V1.0
• Power Supply Reference Design for Intel® Core i3, i5, i7

Trending ArticlesMore

• ByteDance continues to acquire
• Highlights of Qualcomm Snapdragon Theme Pavilion at ChinaJoy
• AMD President and CEO Dr. Lisa Su at CES 2021, Showcasing a Digital-First World
• Use trace-event to solve the problem that the system cannot go into deep sleep
• Millimeter wave stereo imaging radar
• Industry insiders warn: Counterfeit chips are slipping into the supply chain
• 09.19 @Chengdu|NI Semiconductor Test Seminar Call
• Intel's acquisition of Micron may be a good deal
• Smart Home Series Articles | Getting Started with Smart Home Audio Design? TI is here to help!