Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■
Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-
fore practical application or usage of the Products.
Please note that TAIYO YUDEN CO., LTD. shall not be responsible for any defects in products or equipment incor-
porating such products, which are caused under the conditions other than those specified in this catalog or indi-
vidual specification.
■
Please contact TAIYO YUDEN CO., LTD. for further details of product specifications as the individual specification
is available.
■
Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■
All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact TAIYO YUDEN CO., LTD. for more detail in ad-
vance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-
rine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-
ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■
The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-
tors (so called
“TAIYO
YUDEN’ official sales channel”
s
).
It is only applicable to the products purchased from any of TAIYO YUDEN’ official sales channel.
s
■
Please note that TAIYO YUDEN CO., LTD. shall have no responsibility for any controversies or disputes that may
occur in connection with a third party's intellectual property rights and other related rights arising from your usage
of products in this catalog. TAIYO YUDEN CO., LTD. grants no license for such rights.
■
Caution for export
Certain items in this catalog may require specific procedures for export according to
“Foreign
Exchange and For-
eign Trade Control Law”of Japan,
“U.S.
Export Administration Regulations” and other applicable regulations.
,
Should you have any question or inquiry on this matter, please contact our sales staff.
1
4
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
■PARTS
NUMBER
*Operating Temp. : -40½+105℃（Including self-generated heat）
REFLOW
L
B M
①
2
0
②
1
6
T
③
1
0 0
④
J △
⑤ ⑥
△＝Blank space
①Series name
Code
LBM
②Dimensions（L×W）
Code
2016
③Packaging
Code
T
Series name
Wound chip inductor for signal line
Dimensions（L×W）［mm½
2.0×1.6
④Nominal inductance
Code
（example）
R12
1R0
100
101
※R＝Decimal point
⑤Inductance tolerance
Code
J
⑥Internal code
Nominal inductance［μH½
0.12
1.00
10
100
INDUCTORS STANDARD INDUCTORS
Packaging
Taping
Inductance tolerance
±5％
／
■STANDARD
EXTERNAL DIMENSIONS / STANDARD QUANTITY
Recommended Land Patterns
Surface Mounting
・Mounting and soldering conditions should be checked beforehand.
・Applicable soldering process to these products is reflow soldering only.
Type
A
B
C
LBM2016
0.6
1.0
1.8
Unit：mm
Standard quantity [pcs]
Paper tape
Embossed tape
－
2000
Unit：mm（inch）
Type
LBM2016
L
2.0±0.2
（0.08±0.008）
W
1.6±0.2
（0.063±0.008）
T
1.6±0.2
（0.063±0.008）
e
0.5±0.2
（0.02±0.008）
i_wound_LBM_e-E02R01
▶
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
1
4
65
WIRE-WOUND CHIP INDUCTORS (LB SERIES)，
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)，
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
■PACKAGING
①Minimum Quantity
Type
LB C3225
CB C3225
LB 3218
LB R2518
LB C2518
LB 2518
CB 2518
CB C2518
LBM2016
LB C2016
LB 2016
CB 2016
CB C2016
LB 2012
LB C2012
LB R2012
CB 2012
CB C2012
CB L2012
LB 1608
LBMF1608
CBMF1608
②Tape material
●Embossed
tape
Standard Quantity ［pcs½
Paper Tape
Embossed Tape
－
－
1000
2000
－
2000
－
2000
－
3000
4000
4000
－
－
－
3000
Top tape
Chip Filled
Sprocket hole
Base tape
Chip cavity
Chip
●Card
board carrier tape
Top tape
Base tape
Chip Filled
Sprocket hole
Bottom tape
Chip cavity
Chip
▶
This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_pack_e-E02R01
京公网安备 11010802033920号
EEWORLD
