The 53504 Solid-State Power Controllers are lightweight, resistant to damage from shock and vibration, and immune to
contact-related problems (contamination, arcing) associated with mechanical equivalents.
Transformer coupling between the input, output and Power Bus stages provides effective isolation of 1000 V RMS. The
Power FET output eliminates bipolar offset and minimizes output voltage drop.
The Control input is CMOS or TTL logic compatible and may operate from a bias supply of 4.5 to 5.5VDC. (See Figure 1)
Integral short-circuit protection, I
2
T trip and output status is provided. The output current flow is continuously monitored and
responds to an over-current condition with an I
2
T trip curve by opening the output. Over-current conditions include Over-
Load and shorted output during Turn-On. An open-collector Fault Status or Output Status (optional) is available to indicate
the fault or switch state. The output remains blocked until the short is removed and the unit reset. This feature prevents
damage to the controller while averting further system failures that may be caused by the short circuit. Output Fault is an
Active Low output remaining high (open) under all operating conditions except during an Output Fault. The optional Output
Status is high when the output is On and Low when the output is Off. Resetting the unit is accomplished by recycling the
input control.
This device is available in various quality levels from COTS to class K including any custom screening requirements. All
components have radiation-hardened equivalents. The basic data sheet part is environmentally screened to H level in
accordance with Table C-IX of MIL-PRF-38534 with no element evaluation or QCI.
ABSOLUTE MAXIMUM RATINGS
1
Isolation voltage .......................................................................................................................................................1000 V RMS
2
Output withstanding voltage ..............................................................................................................100, 200, 400 or 500 VDC
3
Transient output voltage …………………………………………………………………. .....................100, 200, 400 or 500 VDC
Load Current ..................................................................................Less Than 8 Times Rated Operating Current / Self Limiting
Bias supply voltage, V
DD
....................................................................................................................................... -.6 to 5.5 VDC
Control Voltage ................................................................................................................. 1 Volt above V
DD
/ Volt below Return
Operating temperature ............................................................................................................................ -55ºC to +125ºC Case
Storage temperature ..........................................................................................................................................-55ºC to +125ºC
Notes:
1
2
3
60 Hz sine wave
Reversing polarity on the output may cause permanent damage
Device rating. Application derating not included in these values
Micropac Industries
cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac
reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION
•
905 E. Walnut St., Garland, TX 75040
•
(972) 272-3571
•
Fax (972) 494-2281
E-MAIL:
microsales@micropac.com
12/29/05 Rev G
www.micropac.com
Pg. 1 of 8
53504
ELECTRICAL CHARACTERISTICS
T
A
= -55 to 125° C
PARAMETER
Input characteristics
CMOS configurations (Figure 1)
Bias supply range, V
DD
Bias current
Input current
Control voltage range
Turn-on voltage (Notes 1, 2)
Turn-off voltage (Notes 1, 2)
Dielectric strength
Output characteristics (Note 3)
Power Bias Supply
Output current, sustaining:
Load Start current (not externally adjustable)
Output Pass Current adjustment range:
Continuous blocking voltage
On-state resistance, R
ds
On-state resistance, R
ds
Turn-on time @ 25ºC case
Turn-off time @ 25ºC case
Off-state leakage
Output Capacitance
Status Output Specification
Trip Reset Time
Status Supply Voltage (open Collector)
Status off leakage current
Status on voltage
High-To-Low Transition Time
Junction temperature
Thermal resistance,
θ
JA
θ
JC
Latching, Isolated Output Solid State Power Controllers
TEST CONDITIONS
MIN
TYP
MAX
UNITS
3.0
5 VDC Input
-0.5
5.0
1
5.5
5
500
6.0
VDC
mA
µ
A
VDC
VDC
VDC
V RMS
2.8
0.5
60 Hz / Input /output / Power Bias/ Case
1000
2.7
3.2
400 VDC
Steady state load Current
Whichever is less
100ms output on time
10 seconds
Output device Rating
25ºC Case (Table 1)
125ºC Case (Table 1)
Figure 2
Figure 2
At Maximum Blocking Voltage
.5
.5
20%
3A
600
0
10
20
mA
%
ADC
900
50
Rating
%
% of Initial
VDC
Ohms
Ohms
2.0
1.0
200
5,000
2.0
480
mS
mS
µ
A
pF
Remove overload & Cycle input
VS = 15 VDC
I
STATUS
= 5 MA @ 25ºC
I
STATUS
= 5 MA
50
5.0
32
4
0.4
20
50
150
30
5
mS
VDC
µADC
VDC
µS
ºC
ºC/W
ºC/W
APPLICATION NOTES:
1. Maximum input switching frequency not to exceed 1 Hz under normal conditions, or into a shorted output.
2. Input transitions should be “bounceless contact” with transitions of <1 ms.
3. System transient suppression must be used to limit switching and fault turn-off current & voltage transients to unit ratings.
Micropac Industries
cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac
reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION
•
905 E. Walnut St., Garland, TX 75040
•
(972) 272-3571
•
Fax (972) 494-2281
www.micropac.com
E-MAIL:
microsales@micropac.com
12/29/05 Rev G
Pg. 2 of 8
53504
100 VDC Units
200 VDC Units
400 VDC Units
500 VDC Units
Latching, Isolated Output Solid State Power Controllers
15A Sustaining
See 53503
See 53503
50 / 90 mΩ
52 / 94 mΩ
20A Sustaining
10 / 15 mΩ
12 / 19 mΩ
22 / 39 mΩ
27 / 49 mΩ
30A Sustaining
7 / 11 mΩ
9 / 15 mΩ
16 / 29 mΩ
20 / 37 mΩ
TABLE 1
25ºC / 125ºC R
ds
On Vales by Unit Voltage and Current Rating.
FIGURE 1
High or Low side isolated switch connection. Full isolation exists between Input Logic and status, Output Switch
connects, Power Bias and Case.
Micropac Industries
cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac
reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION
•
905 E. Walnut St., Garland, TX 75040
•
(972) 272-3571
•
Fax (972) 494-2281
www.micropac.com
E-MAIL:
microsales@micropac.com
12/29/05 Rev G
Pg. 3 of 8
53504
Latching, Isolated Output Solid State Power Controllers
1 ms
CONTROL
10%
MAX
90%
90%
10%
t
ON
90%
LOAD VOLTAGE
10%
10%
t
OFF
Figure 2 Switching Characteristics
VDD
CONTROL
OFF
ON
ON
SIMULATED
SHORT
OFF
3A
I
OUT
OUTPUT STATUS
OFF
ON
(OPEN)
Figure 3 - TIMING DIAGRAM
Note 1: A turn-off into a short produces an increase in current to the initial I
2
T must trip value.
Note 2: Shorted while On from any On operating condition can have a
µs
surge current of as much as
1000A.
Note 3: Loss of and re-application of Bus power will result in a re-start (output open & Output Status low.)
Note 4: Output Status signal assumes a pull-up voltage is always present to produce a “1” when status is open.
Micropac Industries
cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac
reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION
•
905 E. Walnut St., Garland, TX 75040
•
(972) 272-3571
•
Fax (972) 494-2281
www.micropac.com
E-MAIL:
microsales@micropac.com
12/29/05 Rev G
Pg. 4 of 8
53504
Latching, Isolated Output Solid State Power Controllers
Truth Table – Power Sequencing
Bus Voltage
0
On
0
On
On
V
DD
Control
I Out
Output
Status
Short
0
X
Open
Open “1”
X
0
X
Open
Open “1”
X
(Note 1)
On
X
Open
0
X
(Note 1,2)
0
Open
0
Off
(Note 3)
Off
(Note 3,4)
Off
(Note 5)
X
X
1
Open “1”
Off
(Note 5)
0
Truth Table – Short circuit and Status
Turn on into Short Sequence
Control
I out
Output
Status
Shorted
Output
0
Off
0
Shorted
1
Off
0
Shorted
1
Off
0
X
0
Off
0
Off
1
On
Open “1”
Off
1
On
Open “1”
Off
Short while on Sequence
1
Off
0
On
1
Off
0
X
0
Off
0
X
1
On
Open “1”
Off
Note 1: Unit Powers up in the Off condition with application of either Bus power or V
DD
.
Note 2: Fault Status reports only when V
DD
is present.
Note 3: Control “0” Off must be invoked upon simultaneous applications of 5V and Bus Power for an unambiguous output
and fault status.
Note 4: An Off Control to On Control transition is required to first turn the Unit On.
Note 5: Loss of V
DD
will not change output state during normal operation.
Note 6: Truth Table Power sequencing: Output Status open collector pull-up resistor is assigned a separate and always
present voltage, producing a “1” when “Open”.
Micropac Industries
cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.
Micropac
reserves the right to make changes at any time in order to improve design and to supply the best product possible.
MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION
In order to facilitate human-computer interaction and display information, a self-made 128*64LCD dot matrix screen is added to the GD32307E-START development board to facilitate subsequent advanced de...
[i=s]This post was last edited by babyking on 2018-11-30 16:51[/i] [color=#333333][font=微软雅黑][size=18px]Today I got a Corethink development board, model SIN-A33, which uses Allwinner's A33 chip. Unlik...
There are many ways to generate digital phase-shifted signals. The traditional direct digital frequency synthesis (DDS) phase-shifting principle is to first digitize the sine wave signal and form a da...
STC89c54RD+ defines array xdata a[18] _at_ 0x001d; I can change its value with the keyboard, but after powering on, its value changes randomly. I would like to ask you how to ensure that its value is ...
I am using a pressure sensor now, but the no-load voltage of the pressure sensor is not 0.
The sensors are all different.
A great person told me to reset the software, but I don't know how to do it. T...
MV-400 high-precision, high-speed image acquisition card 【Features 】MV-400 high-precision, high-speed image acquisition card is a mature and stable high-precision true color ( black and white ) real-t...
What is power factor compensation and what is power factor correction:
Power factor compensation: In the 1950s, an improvement method was proposed for the low power supply efficiency caused by the ...[Details]
Although both the swirl flowmeter and the vortex flowmeter are flowmeters that use the principle of fluid oscillation, they use two completely different working principles. Flowmeter using the Karm...[Details]
Microchip Launches Industry's Most Versatile maXTouch® Touchscreen Controller, Offering Unparalleled Screen Format Flexibility
MXT1296M1T offers various communication options, ISO 26...[Details]
1. Introduction
Relay is one of the key components of automatic control systems, remote control and telemetry systems, and communication systems. It is widely used in aviation, aerospace, electroni...[Details]
From the birth of Tektronix in 1946 to the beginning of the new year in 2024, oscilloscopes have continued to improve from the first commercial oscilloscope to analog oscilloscopes to digital oscillo...[Details]
As electronic products continue to miniaturize and integrate functions, the limitations of traditional discrete logic devices are becoming increasingly apparent. Texas Instruments (TI) recently rel...[Details]
As the name suggests, the working principle of a digital multimeter is mainly based on digital circuits to detect and analyze signals, and then provide LCD display through an analog-to-digital conver...[Details]
What is the concept of energy internet? The author believes that energy internet is based on smart grid, interconnected with various types of networks such as heat pipe network, natural gas pipe ne...[Details]
Well-known whistleblower evleaks discovered that five devices appeared on OnePlus' website. evleaks noted that two of the five devices are flagships: the OnePlus 8T and OnePlus 8T Pro. It ...[Details]
Foreign media 9to5 Google reported that due to the implementation of daylight saving time in the United States and Canada, some Google Pixel phones did not get the update and jumped an hour. Fort...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
Abstract: This article will start with the author's usual nonsensical style of talking, and introduce the relevant knowledge of eye diagram measurement from four aspects: 1. Background knowledge o...[Details]
Semi-automatic block railway lines exist in large numbers in China, and the block information used to connect a train between two stations is completed by two types of information: positive and n...[Details]
Trimedia integrated circuit is a high-performance DSP and CPU recently launched by Philips for multimedia applications. It can perform high-quality video and audio processing. Trimedia currently ...[Details]
Anyone who has used a power bank knows that if you charge your phone once a day, the power banks on the market can charge your phone 4-5 times. A 10,000 mAh power bank can only charge it less than ...[Details]
GD32 MCU
京公网安备 11010802033920号
EEWORLD
