FULL SIZE D.I.L.
VOLTAGE
CONTROLLED
OSCILLATORS
10KH PECL Logic, 0° to 70°C
M2051 thru M2057
L2051 thru L2057
M2061 thru M2063
L2061 thru L2063
M2071 thru M2073
L2071 thru L2073
Thru-Hole, 5V
1 MHz to 175 MHz
PECL 10KH –
Thru-Hole VCXOs, 5V
These thru-hole VCXOs are designed for
compatibility with digital and communications
systems based on the PECL 10KH logic family.
They provide fast rise times, wide frequency
range, and good waveform symmetry at
economical cost.
Users have a choice of a dozen off-the-shelf
models. Diverse combinations of pull, control
voltage and center frequency deviation are
available, accommodating a wide variety of
filtering and driving circuitry. These VCXOs are
hermetically sealed in full size (M) DIL packages
with four pins. MF Electronics’ PECL VCXOs
and are available at frequencies from 12.5 to
175 MHz. Frequency stability choices extend
from ±25 ppm, to 50 ppm.
All VCXOs are single-ended and tested and
guaranteed over the full operating temperature.
For superior performance, including comple-
mentary outputs, see our series 2900s VCXOs
based on ECLPS logic.
These thru-hole PECL VCXOs generate a PECL
frequency output which is controlled by an input
voltage. The end-point frequency/voltage parameters
are defined, as is the center frequency.
CAPTURE RANGE
The Frequency-Capture range is equal to the (Center-Frequency ± the
Frequency Deviation), because every MF VCXO is ATE-tested to meet the
Frequency-Deviation over the temperature range.
Frequency Capture
specification includes all effects of temperature and supply voltage.
It is not necessary to make additional capture allowances.
FEATURES
•
Frequency from 1 MHz to 175 MHz
•
Capture-range is fully defined, under all conditions
•
Start-up time less than 5 ms.
•
10 KH Logic
DOT
DENOTES
PIN 1
.800
±
.005
.200 MAX
.215 MAX
.018
±
.001
.060 TYP
.300
±
.005
.400
.600
±
.005
Pin 1
.008/025 .15 MIN
CONNECTIONS
Full
Size
Pin 1.
Pin 7.
Pin 8.
Pin 14.
.100
±
.005
Pin 7
.300
±.
005
.500
±
.005
Control Voltage, V
C
Ground & Case
Output
+5 Volts, V
DD
.150
Pin 14
Pin 8
.250 MAX
GLASS INSULATORS (4)
on .48 x .18 ctrs.
“M” Package – “L” Package
is same as “M”
but seated height is 0.190
ELECTRONICS
10 Commerce Drive, New Rochelle, NY10801
•
914-576-6570
•
Fax: 914-576-6204
•
http://www.mfelectronics.com
•
email:mfsales@mfelec.com
102
FULL SIZE D.I.L.
VOLTAGE CONTROLLED OSCILLATORS
10KH PECL Logic, 0° to 70°C
Thru-Hole, 5V
1 MHz to 175 MHz
M2051 thru M2057
L2051 thru L2057
M2061 thru M2063
L2061 thru L2063
M2071 thru M2073
L2071 thru L2073
Center Frequency is Between Two Voltages
with ±50 ppm stability
Control
Voltage
(Volts)
0.3 to 10.0
0.3 to 4.0
0.3 to 10.0
0.3 to 4.0
1.0 to 4.0
0 to 5.0
0.5 to 4.5
Frequency
Deviation
(ppm)
± 175 min
± 75 min
± 175 to 300
± 125 min
± 75 to 300
± 150 min
± 125 to 250
Guaranteed Control
Center
Capture
Voltage Frequency
Range
at Center Stability
(ppm)
Frequency
(ppm)
± 175
± 75
± 175
± 125
± 75
± 150
± 125
2.5 to 5.0
1.3 to 2.3
2.5 to 5.0
1.3 to 2.3
1.8 to 3.0
—
1.8 to 3.0
DESCRIPTIONS
M2051, L2051
M2052, L2052
M2053, L2053
M2054, L2054
M2055, L2055
±175 ppm, min. deviation when using
0.3 to 10V control-voltage
±75 ppm, min. deviation when using
0 to 4.0V control-voltage
±175 ppm to ±300 ppm deviation when using
0.3 to 10V control-voltage
±125 ppm min. deviation when using
0.3 to 4.0V control-voltage
±75 ppm to ±300 ppm deviation when using
1.0 to 4.0V control-voltage, for use where the
control voltage is 1 volt off both rails
±150 ppm, min. deviation when using
0 to 5.0V rail-to-rail control-voltage
±125 ppm to ±250 ppm deviation when using
0.5 to 4.5V control-voltage
±75 ppm capture when using using 0.5 to 4.5V
control-voltage and 2.5V center with ±50 ppm stability
±100 ppm capture when using using 0.5 to 4.5V
control-voltage and 2.5V center with ±50 ppm stability
±150 ppm capture when using using 0.5 to 4.5V
control-voltage and 2.5V center with ±50 ppm stability
±75 ppm capture when using using 0.5 to 4.5V
control-voltage and 2.5V center with ±25 ppm stability
±100 ppm capture when using using 0.5 to 4.5V
control-voltage and 2.5V center with ±25 ppm stability
±150 ppm capture when using using 0.5 to 4.5V
control-voltage and 2.5V center with ±25 ppm stability
MODEL
2051
2052
2053
2054
2055
2056
2057
± 30, typ
± 50, max
M2056, L2056
Center Frequency is at 2.5V with ±50 ppm stability
Control
Voltage
(Volts)
0.5 to 4.5
0.5 to 4.5
0.5 to 4.5
Frequency
Deviation
(ppm)
± 75 to 150
± 100 to 200
± 150 to 300
Guaranteed Control
Center
Capture
Voltage Frequency
Range
at Center Stability
(ppm)
Frequency
(ppm)
± 75
± 100
± 150
2.5
2.5
2.5
± 30, typ
± 50, max
M2057, L2057
M2061, L2061
M2062, L2062
M2063, L2063
MODEL
2061
2062
2063
Center Frequency is at 2.5V with ±25 ppm stability
Control
Voltage
(Volts)
0.5 to 4.5
0.5 to 4.5
0.5 to 4.5
Frequency
Deviation
(ppm)
± 75 to 150
± 100 to 200
± 150 to 300
Guaranteed Control
Center
Capture
Voltage Frequency
Range
at Center Stability
(ppm)
Frequency
(ppm)
± 75
± 100
± 150
2.5
2.5
2.5
± 20, typ
± 25, max
M2071, L2071
M2072, L2072
M2073, L2073
MODEL
2071
2072
2073
PIN 1.
CONTROL VOLTAGE
V
DD
+5V
Power
Supply
GND
MA
1
14
FET PROBE
350 MHz
SCOPE
LOAD
Y-OUTPUT
FREQUENCY STABILITY
Frequency stability vs. Temperature (0 to 70°C) is typically better than
±20 ppm. Since the deviation of each oscillator is tested and guaranteed
over the whole operating temperature range, it is not necessary to make
additional capture allowance. All oscillators will capture frequencies with the
full minimum values of the deviation under all conditions.
QUALITY
Each VCXO is computer-tested at three temperatures to guarantee
full compliance to the specification.
7
8
COUNTER
To adapt Fet probe to receptacle
use Tektronix Part #103-0164-00
To connect output to scope use
use Tektronix Part #131-0258-00 (receptacle)
ALL OSCILLATORS HAVE INTERNAL BYPASS CAPACITORS
TEST CIRCUIT
ELECTRONICS
10 Commerce Drive, New Rochelle, NY10801
•
914-576-6570
•
Fax: 914-576-6204
•
http://www.mfelectronics.com
•
email:mfsales@mfelec.com
103
FULL SIZE D.I.L.
VOLTAGE CONTROLLED OSCILLATORS
10KH PECL Logic, 0° to 70°C
Thru-Hole, 5V
1 MHz to 175 MHz
M2051 thru M2057
L2051 thru L2057
M2061 thru M2063
L2061 thru L2063
M2071 thru M2073
L2071 thru L2073
SPECIFICATIONS
Temperature
Operating
Storage
0 to 70°C
–55 to +125°C
ENVIRONMENTAL SPECIFICATIONS
Temperature Cycle
– Not to exceed ±5 ppm change when exposed to 2
hours maximum at each temperature from 0 to 120°C, with 25°C reference
Shock
– 1000 G's, 0.35 ms, 1/2 sine wave, 3 shocks in each plane
Vibration
– 10-2000 Hz of .06" d.a. or 20 G's, whichever is less
Humidity
– Resistant to 85° R.H. at 85°C
MECHANICAL SPECIFICATIONS
Frequency Stability
V
C
= 2.5V
±20, ±25 or ±50 ppm, max.
as shown in model specification
MIN.
4.5
TYP
5.0
30
MAX
5.5
45
UNITS
volts
ma
Input Voltage
Input Current
Output Levels
“0” Level
25°C
70°C
“1” Level
25°C
70°C
Rise and Fall Times
(20 to 80%)
Symmetry
Input Impedance,
Pin 5., Control Voltage
Control Voltage Bandwidth
Gross Leak
– Each unit checked in 125°C flurocarbon
Fine Leak
– Mass spectrometer leak rate less than 2 X 10-8 atmos,
cc/sec of helium
Pins
– Kovar, with 7 microinch gold over nickel
Bend Test
– Will withstand two bends of 90° from reference
Header
– Steel, with gold over nickel
Case
– Stainless steel, type 304
Marking
– Printing is black epoxy ink
Resistance to Solvents
– MIL STD 202, Method 215
AGING
3 to 5 ppm, first year, typ.
1 ppm per year thereafter, typ.
(V
DD
-1.95)
(V
DD
-1.95)
(V
DD
-0.98)
(V
DD
-0.92)
(V
DD
-1.63)
(V
DD
-1.60)
(V
DD
-0.81)
(V
DD
-.735)
volts
volts
volts
volts
1.0
48/52
2.0
45/55
ns
percent
15
15
1000
150
Kohms
KHz
Fig. 1 M2072 - 80M
ELECTRONICS
10 Commerce Drive, New Rochelle, NY10801
•
914-576-6570
•
Fax: 914-576-6204
•
http://www.mfelectronics.com
•
email:mfsales@mfelec.com
104
FULL SIZE D.I.L.
VOLTAGE CONTROLLED OSCILLATORS
10KH PECL Logic, 0° to 70°C
Thru-Hole, 5V
1 MHz to 175 MHz
M2051 thru M2057
L2051 thru L2057
M2061 thru M2063
L2061 thru L2063
M2071 thru M2073
L2071 thru L2073
DEVIATION vs CONTROL VOLTAGE
FOR M2073- 80M, TYPICAL
Deviation from Nominal Frequency, ppm
250
200
150
100
50
0
-50
-100
-150
-200
-250
0.0
1.0
2.0
3.0
4.0
5.0
V
DD
= 5.5V
V
DD
= 5.0V
V
DD
= 4.5V
Control Voltage, Vc
Fig. 2 Deviation vs. Control Voltage
at 0°C
Deviation from Nominal Frequency, ppm
200
150
100
50
0
-50
-100
-150
-200
-250
0.0
1.0
2.0
3.0
4.0
5.0
V
DD
= 5.5V
V
DD
= 5.0V
V
DD
= 4.5V
Deviation from Nominal Frequency, ppm
250
250
200
150
100
50
0
-50
-100
-150
-200
-250
0.0
1.0
2.0
3.0
4.0
5.0
V
DD
= 5.5V
V
DD
= 5.0V
V
DD
= 4.5V
Control Voltage, Vc
Control Voltage, Vc
Fig. 3 Deviation vs. Control Voltage
at 25°C
Fig. 4 Deviation vs. Control Voltage
at 70°C
HOW TO ORDER
For Part Number, put package type before model number,
and add frequency in MHz, for example:
M 2056 - 126M
G
“M” is full size DIL
“H” is half size DIL
“L” is low height,
full size DIL
“2056”
is model
type
“126 M”
frequency in MHz
Add
“G”
for
gullwing
ELECTRONICS
10 Commerce Drive, New Rochelle, NY10801
•
914-576-6570
•
Fax: 914-576-6204
•
http://www.mfelectronics.com
•
email:mfsales@mfelec.com
105
京公网安备 11010802033920号
EEWORLD
