Little Demon
®
Carbon Composition Molded
5% & 10% Tolerance
OD/OF Series
F e at u r e S
• Molded insulation for high dielectric strength
• Rugged construction
• High surge capabilities
• Comparable to “Mil” RC07, RC20, and RC32 types
• OD/OF Series available in E24 values; E12 values
above 100KΩ
Ohmite’s Little Demons are small, reliable carbon
composition resistors with exceptional strength.
They are made tough by a molding process that
combines the terminals, insulation and resistive ele-
ment into an integrated unit. Along with their small
size, Little Demons perform with low noise, dissipate
heat rapidly and offer high temperature stability.
Color codes are readable even after prolonged use
thanks to a very durable coating that resists abra-
sions and chipping normally associated with auto-
matic insertion equipment.
S e r i e S S p e c i F i c at i O n S
Series
OD
OF
Mil-R-11 Type
RC07
RC20
Wattage
Ohms
0.25 2.2Ω - <100K
100K - 5.6M
0.50 2.2Ω - <100K
100K - 20M
Tolerance
±5%
±10%
±5%
±10%
Max. Voltage
250
350
Dielectric VAC
500
700
characteriSticS
Terminals
Solder-coated copper terminal.
Body
Molded Phenolic
Tolerance
±5% (<100KΩ);
±10% (>100KΩ)
Derating
Linearly from 100% @ +70°C to 0% @ 130°C
100,000
10,000
Pulse Power (W)
1,000
100
10
1
10
-7
Single Pulse Power Capability
OF
OD
10
-6
10
-5
10
-4
10
-3
10
-2
Pulse width (s)
10
-1
1
DimenSiOnS
1.135"
±0.12
28.83mm
±3
L
D
Series Length max.
OD
OF
0.276 / 7.0
0.406 /10.3
Diam. max.
0.098 / 2.5
0.150 / 3.8
Lead Dia.
0.024/0.60
0.028/0.70
(continued)
92
1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com
Little Demon
®
Carbon Composition Molded
5% & 10% Tolerance
pa c k a g i n g
OD/OF Series
All resistors are packaged in sealed poly bags with desiccant
to maintain a consistent humidity during storage. If parts are
removed from the protective plastic bag they should be used
as soon as possible or resealed in the plastic bag.
Tape/Reel
OD
OF
Storage:
Ohmite recommends storing carbon composition
resistors in a controlled environment at a temperature of 5° to
35°C and relative humidity of less than 60%. Inventory should
always be used on a first-in-first-out basis.
280mm
(ref.)
260mm
±5
Qty./reel
5000
3000
Reel size (mm)
260
260
Qty./carton
40,000 24,000
Gross carton wt. (kg)
12
13
Carton size (m
3
)
0.04
0.04
Ammo Box
OD
OF
0.5mm max.
52.4mm +1.6
-1.4
6mm
±.5
5.08mm
±.38
1mm max.
60mm
±5
(OD)
65mm
±5
(OF)
455mm ±5
Tape width (mm)
52
52
Qty./box
2000
2000
Qty./carton
30,000 30,000
Gross carton wt. (kg)
10
16
Carton size (m3)
0.03
0.05
14.5mm
±.5
75mm
±5
3mm
60.4mm±1
L
1
– L
2
= 1mm max.
L
1
L
2
3.2mm min.
75mm
±5
60.4mm
±1
reSiStOr uSe guiDelineS
Carbon composition resistors are manufactured by extruding
a blend of carbon and organic binders inside a phenolic outer
body. The extrusion is cut to length, leads inserted, cured,
and marked to form a finished resistor. The carbon and binder
mixture is adjusted to produce different resistance values. The
resistors are sorted for 5%, 10%, and 20% tolerance values.
Carbon composition resistors are able to withstand larger
short-term pulses and higher voltages than film resistors and
are virtually impervious to ESD events (Electro-static dis-
charge). Carbon composition resistors are also sensitive to
moisture and, therefore, storage recommendations should be
adhered to. Generally, any moisture absorbed during storage
will be "baked out" during the soldering operation. If the prod-
uct is stored properly the resistance shift during the soldering
operation will be minimal, less than 2% or 3%.
Carbon composition resistors are highly hygroscopic
and
changes in resistance value can occur if too much moisture is
absorbed. For this reason, it is recommended not to use water
or water-soluble solvents to clean these components. Alcohol
or hydrocarbon solvents are recommended for rinsing.
bake prOceDure anD cautiOnS
A. Heat Treatment
110°C ±10°C
15 hours
B. Frequency of
heat treatment
1 time only
C. Solder heat test after treatment
Solder
Dip
Type
Temp.
Time
Evaluation
OD
300°C
3 sec within ±3%
OF
350°C
3 sec within ±3%
*Depth of Immersion: 4mm from the resistor
body
D. Cautions
Solderability:
may be affected due to oxidization of lead wire
Resistance value:
some units may not completely recover to
original value.
Soldering heat:
some treated product may have substantial
resistance change during soldering operation. It is recom-
mended that parts be tested to evaluate soldering heat
effects. Solder should not come in contact within 4mm of
resistor body as this may cause a significant shift in resis-
tance value due to high heat exposure.
O r D e r i n g i n F O r m at i O n
• OD/OF Series available in E24 values
RoHS compliant
O D 6 8 3 J E
-TR
Series
Ohms
OD
68G
=
6.8
OF
680 =
68
681
=
680
682
=
6,800
683
=
68,000
684
=
680,000
Tolerance
<100KΩ : J = 5%
>100KΩ : K = 10%
Packaging
None = cut reel, 100/bag (std.)
-TR = taped and reeled
-A
= ammo pack
-B
= bulk (loose)
rev 11/18-1
1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • info@ohmite.com
93
京公网安备 11010802033920号
EEWORLD
