Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
TMS320C6713B is an upgraded version of TMS320C6713, which upgrades Silicon Revision to 2.0. The difference between the two is noted in the "spra851h" document. See the link: http://www.ti.com/lit/an/s...
1. Use VNA to measure the series equivalent parameters L, R and C of the antenna; 2. Increase the sweep range to find an intersection; 3. Increase the filter capacitance and move the intersection up. ...
What factors should be considered when designing a high-quality, stable power supply ? What details should be paid attention to? What are the design and processing tips?
Welcome everyone to chat~
In t...
As shown in the red box below:
1. What are the functions of R14 and R15 in the figure?
2. What are the functions of C22 and C23 in the figure? Thank you!...
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 19:58[/i] July 12, according to foreign media reports, on Tuesday, Time Warner said it plans to announce the business strategy plan of its...
On June 25-26, the 2021 Fifth Jiwei Semiconductor Summit with the theme of "The Heart and the Core are Imprinted, and the Changes are Kunpeng" was officially held in Haicang, Xiamen, and lasted for t...[Details]
0 Preface
When processing complex surfaces, multi-axis CNC systems require the coordination of various axes, and high real-time and reliability requirements. The CAN bus can provide a data transm...[Details]
Analysis of the advantages and disadvantages of embedded technology The benefits of engaging in embedded software development are: 1 Currently, there is a shortage of people in this field both ...[Details]
At present, the smoothing of power peak-valley difference, the safety, reliability and power quality of the power grid, the development of renewable energy and the development of smart grid technolog...[Details]
Under the special background of epidemic prevention and control in the first half of the year, the resumption of work and production in many places was postponed, and the investment plans of some maj...[Details]
Purpose: Familiar with using MCU to simulate reading and writing 24C01EEPROM 1. First write data to 24C01EEPROM 2. Read data from 24C01EEPROM and display it with LED Hardware Setup: 1. All SW4 swit...[Details]
“Toshiba of the new era”, can the new era still come?
Toshiba, known as the "light of Japanese manufacturing", has products covering white goods, power equipment,
medical
equipment...[Details]
Google released the Pixel Buds last year, but they could only be charged via a cable. The upcoming version is expected to include wireless charging, and information about the new Buds has appea...[Details]
With the theme of "Gathering Wisdom, Creating the Future", the 2019 STM32 Summit focuses on three major topics: artificial intelligence and computing, industry and security, and cloud technology and ...[Details]
0Introduction
WSN (Wireless Sensor Network) is a multi-hop self-organizing network that collaboratively senses, collects and processes information about objects in the network coverage area th...[Details]
The advanced timer is similar to the general timer. The following is a PWM program for TIM1. TIM1 is the only advanced timer in STM32. There are 4 channels with dead zone and complementary. Fir...[Details]
Preface
Digital optical power meter is a portable instrument controlled by a single-chip microcomputer that can measure the strength of optical signals. It is an important instrument for lay...[Details]
In recent years, car entertainment systems have developed rapidly. From the perspective of market demand, users' requirements for multimedia entertainment have gradually increased. At the same time...[Details]
According to semimedia, NXP invested $100 million to expand the production line of 5G mobile network transistors and RF power amplifiers at its Chandler factory in Arizona, USA, which officially star...[Details]
Find X8 Pro will be equipped with the industry's only dual periscope telephoto lens and the first inverted periscope camera.
The Find X8 series is the first to be equipped with AI ...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
