REVISIONS
LTR
A
B
C
DESCRIPTION
Added suggested sources of supply; made
editorial changes.
Added suggested sources of supply.
Deleted and added suggested sources of supply.
Editorial changes throughout.
Added suggested sources of supply. Changes
to manufacturer PIN. Changes to paragraphs
3.2.2, 3.2.6, and 6.1. Editorial changes
throughout.
Changes in accordance with NOR 5910-R004-96
Revised sources of supply, added alternate
marking method, made editorial changes, and
converted references to MIL-PRF-49467.
Moved solderability testing from group A to group
B. Updated suggested sources of supply.
Removed suggested source of supply. Added
note 4 to figure 1. Added capacitor tolerance
note to 3.2.9.
Added suggested source of supply. Changed
Johanson Dielectrics CAGE code.
Updated name and address of vendor C.
Added Johanson Dielectrics as a suggested
source of supply.
Added CalRamic Technologies as a suggested
source of supply.
Changed drawing type to Source Control with
approved sources. Added manufacturer
eligibility criteria, paragraph 3.14. Added new
paragraph 6.3. Added an approved source.
DATE
25 Sep 87
11 May 88
8 Oct 92
APPROVED
D. Moore
D. Moore
D. Moore
D
E
F
G
H
J
K
L
M
23 Feb 94
23 May 96
5 April 99
10 April 00
16 January 01
12 September 01
4 November 02
18 August 2004
19 April 2007
D. Moore
A. Ernst
J. Crum
Kendall A. Cottongim
Kendall A. Cottongim
Kendall A. Cottongim
Kendall A. Cottongim
Kendall A. Cottongim
Michael A. Radecki
N
21 October 2010
Michael A. Radecki
CURRENT DESIGN ACTIVITY CAGE CODE 037Z3
HAS CHANGED NAMES TO:
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
Prepared in accordance with
ASME Y14.100
REV STATUS
OF PAGES
PMIC N/A
REV
PAGES
N
1
N
2
N
3
N
4
N
5
N
6
N
7
N
8
N
9
Source control drawing
PREPARED BY
ROBERT E. GRILLOT
CHECKED BY
EDWARD H. BACK
APPROVED BY
DAVID E. MOORE
SIZE
A
CODE IDENT. NO.
14933
DEFENSE ELECTRONIC SUPPLY CENTER
DAYTON, OH 45444-5000
Original date of
drawing
1 April 1987
TITLE
CAPACITORS, CERAMIC, MULTILAYER, HIGH
VOLTAGE, X7R, 1,000 V DC
DWG NO.
87043
PAGE
1
REV
AMSC N/A
N
OF
9
5910-E475
1. SCOPE
1.1 Scope. This drawing and
MIL-PRF-49467
describe the requirements for high voltage multilayer ceramic capacitors.
1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows:
87043
|
|
Drawing
number
2. APPLICABLE DOCUMENTS
2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not
include documents cited in other sections of this specification or recommended for additional information or as examples. While every
effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified
requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed.
2.2 Government documents.
2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this
document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation
or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-49467
-
Capacitor, Fixed, Ceramic, Multilayer, High Voltage (General Purpose),
Established Reliability, General Specification for.
-XX
|
|
Dash number
(see table I)
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-202
MIL-STD-1285
-
-
Test Methods Standard Electronics and Electrical Component Parts.
Marking of Electrical and Electronic Parts.
(Copies of these documents are available online at
https://assist.daps.dla.mil/quicksearch/
or
https://www.assist.daps.dla.mil/
or
from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this
document and the references cited herein, the text of this document takes precedence. Nothing in this document, however,
supersedes applicable laws and regulations unless a specific exemption has been obtained.
3. REQUIREMENTS
3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in
MIL-PRF-49467
and herein
(see figure 1).
3.1.1 Leads. Leads shall be solder coated. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 3
percent.
3.1.2 Case. Epoxy, conformally coated.
3.1.3 Operating temperature range. The operating temperature range shall be -55°C to +125°C.
3.2 Electrical characteristics.
3.2.1 Rated voltage. The rated voltage shall be 1,000 volts dc.
3.2.2 Dielectric type. X7R.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO
SIZE
CODE IDENT NO.
14933
REV N
DWG NO.
A
87043
PAGE
2
Case
code
A
B
C
D
E
F
G
Width
(W)
.250
.320
.370
.470
.570
.670
.770
Sizes (max.)
Height
Thickness
(H)
(T)
.220
.280
.300
.400
.500
.600
.720
.200
.250
.250
.270
.270
.270
.270
Lead spacing
±
.030
(S)
.170
.220
.275
.375
.475
.575
.675
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. H dimension includes meniscus.
4. S dimension shall be maintained from chip body to end of leads.
Inches
.002
.025
.030
.170
.200
.220
.250
.270
.275
.280
.300
.320
.370
mm
0.05
0.64
0.76
4.32
5.08
5.59
6.35
6.86
6.99
7.11
7.62
8.13
9.40
Inches
.375
.400
.470
.475
.500
.570
.575
.600
.670
.675
.720
.770
1.250
mm
9.53
10.16
11.94
12.07
12.70
14.48
14.61
15.24
17.02
17.15
18.29
19.56
31.75
FIGURE 1. Case dimensions and configuration.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO
SIZE
CODE IDENT NO.
14933
REV N
DWG NO.
A
87043
PAGE
3
3.2.3 Temperature coefficient. ±15 percent. (For
MIL-PRF-49467
group B voltage temperature limits, use step a through step d
only.)
3.2.4 Capacitance. See table I. Measured in accordance with
method 305 of MIL-STD-202,
1 kHz at 1.0 V rms at +25°C.
3.2.5 Dissipation factor (+25°C). 2.5 percent maximum (measured under the same conditions as capacitance).
3.2.6 Insulation resistance. Measured in accordance with
method 302 of MIL-STD-202.
At +25°C, 500 V dc: 100,000 megohms or
1,000 megohms microfarad, whichever is less. At +125°C, 500 V dc: 10,000 megohms or 100 megohms microfarad, whichever is
less.
3.2.7 Dielectric withstanding voltage. 1.2 times rated voltage.
3.2.8 Aging rate. -2.0 percent maximum per decade-hour.
3.2.9 Capacitance tolerance. K = ±10 percent, M = ±20 percent. K tolerance parts may be substituted for M tolerance parts, with
acquiring activity approval.
3.3 Solderability of terminals. In accordance with
MIL-PRF-49467.
3.4 Vibration. In accordance with
MIL-PRF-49467.
3.5 Shock. In accordance with
MIL-PRF-49467.
3.6 Immersion cycling. In accordance with
MIL-PRF-49467.
3.7 Moisture resistance. In accordance with
MIL-PRF-49467.
3.8 Life. One hundred percent of rated voltage applied at +125°C for 1,000 hours. Resistors with a high value such as 1 megohm
may be used in series with each part under test in lieu of fuses.
3.9 Thermal shock.
Method 107, MIL-STD-202,
test condition B except low temperature is -55°C.
3.10 Voltage conditioning. In accordance with
MIL-PRF-49467,
100 percent of rated voltage. Resistors with a high value such as 1
megohm may be used in series with each part under test in lieu of fuses.
3.11 Terminal strength. In accordance with
MIL-PRF-49467.
3.12 Marking. Marking shall be in accordance with
MIL-STD-1285
except the capacitors shall be marked with the PIN as specified
in 1.2, the manufacturer’s name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum. Case codes
A, B, and C (at the option of the manufacturer) may be marked as indicated below with full marking on the package.
Front
Last 3 digits of drawing number----
Dash number --------------------------
043
-49
Back
XYZ
430
------ Manufacturer’s trademark
------ Date code
FIGURE 2. Alternate marking method for A, B, and C case codes.
3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials
should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance
requirements, and promotes economically advantageous life cycle costs.
3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the
MIL-PRF-49467
Qualified Products Database for at least one part, or provide data as requested by DLA Land and Maritime – VAT.
3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved
source of supply.
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO
SIZE
CODE IDENT NO.
14933
REV N
DWG NO.
A
87043
PAGE
4
3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or
appearance.
TABLE I. Electrical characteristics
DSCC
drawing
87043-
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Capacitance
100 pF
100 pF
120 pF
120 pF
150 pF
150 pF
180 pF
180 pF
220 pF
220 pF
270 pF
270 pF
330 pF
330 pF
390 pF
390 pF
470 pF
470 pF
560 pF
560 pF
680 pF
680 pF
820 pF
820 pF
1000 pF
1000 pF
1200 pF
1200 pF
1500 pF
1500 pF
1800 pF
1800 pF
2200 pF
2200 pF
2700 pF
2700 pF
3300 pF
3300 pF
3900 pF
3900 pF
4700 pF
4700 pF
5600 pF
5600 pF
6800 pF
Capacitance
tolerance
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
Case code
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
DSCC
drawing
87043-
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
Capacitance
6800 pF
8200 pF
8200 pF
.01
µF
.01
µF
.012
µF
.012
µF
.015
µF
.015
µF
.018
µF
.018
µF
.022
µF
.022
µF
.027
µF
.027
µF
.033
µF
.033
µF
.039
µF
.039
µF
.047
µF
.047
µF
.056
µF
.056
µF
.068
µF
.068
µF
.082
µF
.082
µF
.10
µF
.10
µF
.12
µF
.12
µF
.15
µF
.15
µF
.18
µF
.18
µF
.22
µF
.22
µF
.27
µF
.27
µF
.33
µF
.33
µF
.39
µF
.39
µF
.47
µF
.47
µF
Capacitance
tolerance
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
K
M
Case code
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
D
D
D
D
D
D
D
D
D
D
E
E
E
E
E
E
E
E
F
F
F
F
F
F
G
G
G
G
G
G
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO
SIZE
CODE IDENT NO.
14933
REV N
DWG NO.
A
87043
PAGE
5
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
