Features
n
Ultra-tight tolerance
01C
Electrical Characteristics
Characteristic
Power Rating @ 70 °C
Operating Temperature Range
Derated to Zero Load at
Maximum Working Voltage
Maximum Overload Voltage
Resistance Range
(E-96 + E-24 Values)
Temperature Coefficient
of Resistance (TCR)
n
Wide resistance range
n
RoHS compliant*
n
Four package sizes available
This series is currently available but
not recommended for new designs.
The Model CRT Series is the suggested
replacement.
CRT-ST Series -
Thin Film Precision Chip Resistors
Model
CRT0402-ST
1/16 watt
Model
Model
CRT0603-ST
CRT0805-ST
1/10 watt
1/8 watt
-55 to +155 °C
+155 °C
75 V
150 V
150 V
300 V
(See Value - TCR Table on Page 2)
25 to 50 PPM/°C (See Value - TCR Table on Page 2)
Model
CRT1206-ST
1/4 watt
50 V
100 V
200 V
400 V
NOTE: TCR code assigned as “X”, see “How to Order”.
Performance Characteristics
Test
Temperature Coefficient
of Resistance (TCR)
Short Time Overload
Insulation Resistance
Endurance
Damp Heat with Load
Bending Strength
Solderability
Resistance to Solder Heat
Thermal Shock
Low Temperature Operation
Test Method
MIL-STD-202 Method 304
JIS-C-5201-1 5.5
RCWV*2.5 or max. overload voltage; whichever is lower, for 5 seconds
MIL-STD-202 Method 302
Apply 100 Vdc for 1 minute
MIL-STD-202 Method 108A
70 ±2 °C, RCWV for 1,000 hours with 1.5 hours “ON” and 0.5 hours “OFF”
MIL-STD-202 Method 103B
40 ±2 °C, 90~95 % R.H., RCWV for 1,000 hours with 1.5 hours “ON” and
0.5 hours “OFF”
JIS-C-5201-1 56.1.4
Bending Amplitude 3 mm for 10 seconds
MIL-STD-202 Method 208H
245 ±5 °C for 3 seconds
MIL-STD-202 Method 210E
260 ±5 °C for 10 seconds
MIL-STD-202 Method 107G
-55 °C to 150 °C, 100 cycles
JIS-C-5201-1 7.1
1 hour, -65 °C, followed by 45 minutes of RCWV
Test Limits
DR
As specified
≤±0.2 %
>10 GW
≤±0.5 %
≤±0.5 %
≤±0.1 %
95 % min. coverage
≤±0.1 %
≤±0.2 %
≤±0.5 %
RCWV (Rated Continuous Working Voltage) =
√
(P*R) or Max. Operating Voltage, whichever is lower.
Environmental Characteristics
Moisture Sensitivity Level ..................... 1
Asia-Pacific:
Tel: +886-2 2562-4117 • Email: asiacus@bourns.com
EMEA:
Tel: +36 88 885 877 • Email: eurocus@bourns.com
The Americas:
Tel: +1-951 781-5500 • Email: americus@bourns.com
www.bourns.com
*RoHS Directive 2015/863, Mar 31, 2015 and Annex.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf.
Legal Disclaimer Notice
This legal disclaimer applies to purchasers and users of Bourns
®
products manufactured by or on behalf of Bourns, Inc. and its
affiliates (collectively, “Bourns”).
Unless otherwise expressly indicated in writing, Bourns
®
products and data sheets relating thereto are subject to change
without notice. Users should check for and obtain the latest relevant information and verify that such information is current and
complete before placing orders for Bourns
®
products.
The characteristics and parameters of a Bourns
®
product set forth in its data sheet are based on laboratory conditions, and
statements regarding the suitability of products for certain types of applications are based on Bourns’ knowledge of typical
requirements in generic applications. The characteristics and parameters of a Bourns
®
product in a user application may vary
from the data sheet characteristics and parameters due to (i) the combination of the Bourns
®
product with other components
in the user’s application, or (ii) the environment of the user application itself. The characteristics and parameters of a Bourns
®
product also can and do vary in different applications and actual performance may vary over time. Users should always verify
the actual performance of the Bourns
®
product in their specific devices and applications, and make their own independent
judgments regarding the amount of additional test margin to design into their device or application to compensate for
differences between laboratory and real world conditions.
Unless Bourns has explicitly designated an individual Bourns
®
product as meeting the requirements of a particular industry
standard (e.g., ISO/TS 16949) or a particular qualification (e.g., UL listed or recognized), Bourns is not responsible for any
failure of an individual Bourns
®
product to meet the requirements of such industry standard or particular qualification. Users of
Bourns
®
products are responsible for ensuring compliance with safety-related requirements and standards applicable to their
devices or applications.
Bourns
®
products are not recommended, authorized or intended for use in nuclear, lifesaving, life-critical or life-sustaining ap-
plications, nor in any other applications where failure or malfunction may result in personal injury, death, or severe property or
environmental damage. Unless expressly and specifically approved in writing by two authorized Bourns representatives on a
case-by-case basis, use of any Bourns
®
products in such unauthorized applications might not be safe and thus is at the user’s
sole risk. Life-critical applications include devices identified by the U.S. Food and Drug Administration as Class III devices and
generally equivalent classifications outside of the United States.
Bourns expressly identifies those Bourns
®
standard products that are suitable for use in automotive applications on such
products’ data sheets in the section entitled “Applications.” Unless expressly and specifically approved in writing by two
authorized Bourns representatives on a case-by-case basis, use of any other Bourns
®
standard products in an automotive
application might not be safe and thus is not recommended, authorized or intended and is at the user’s sole risk. If Bourns
expressly identifies a sub-category of automotive application in the data sheet for its standard products (such as infotainment
or lighting), such identification means that Bourns has reviewed its standard product and has determined that if such Bourns
®
standard product is considered for potential use in automotive applications, it should only be used in such sub-category of
automotive applications. Any reference to Bourns
®
standard product in the data sheet as compliant with the AEC-Q standard
or “automotive grade” does not by itself mean that Bourns has approved such product for use in an automotive application.
Bourns
®
standard products are not tested to comply with United States Federal Aviation Administration standards generally
or any other generally equivalent governmental organization standard applicable to products designed or manufactured for
use in aircraft or space applications. Bourns expressly identifies Bourns
®
standard products that are suitable for use in aircraft
or space applications on such products’ data sheets in the section entitled “Applications.” Unless expressly and specifically
approved in writing by two authorized Bourns representatives on a case-by-case basis, use of any other Bourns
®
standard
product in an aircraft or space application might not be safe and thus is not recommended, authorized or intended and is at the
user’s sole risk.
The use and level of testing applicable to Bourns
®
custom products shall be negotiated on a case-by-case basis by Bourns and
the user for which such Bourns
®
custom products are specially designed. Absent a written agreement between Bourns and the
user regarding the use and level of such testing, the above provisions applicable to Bourns
®
standard products shall also apply
to such Bourns
®
custom products.
Users shall not sell, transfer, export or re-export any Bourns
®
products or technology for use in activities which involve the
design, development, production, use or stockpiling of nuclear, chemical or biological weapons or missiles, nor shall they use
Bourns
®
products or technology in any facility which engages in activities relating to such devices. The foregoing restrictions
apply to all uses and applications that violate national or international prohibitions, including embargos or international
regulations. Further, Bourns
®
products and Bourns technology and technical data may not under any circumstance be
exported or re-exported to countries subject to international sanctions or embargoes. Bourns
®
products may not, without prior
authorization from Bourns and/or the U.S. Government, be resold, transferred, or re-exported to any party not eligible
to receive U.S. commodities, software, and technical data.
To the maximum extent permitted by applicable law, Bourns disclaims (i) any and all liability for special, punitive, consequential,
incidental or indirect damages or lost revenues or lost profits, and (ii) any and all implied warranties, including implied warranties
of fitness for particular purpose, non-infringement and merchantability.
For your convenience, copies of this Legal Disclaimer Notice with German, Spanish, Japanese, Traditional Chinese and Simplified Chinese
bilingual versions are available at:
Web Page:
http://www.bourns.com/legal/disclaimers-terms-and-policies
PDF:
http://www.bourns.com/docs/Legal/disclaimer.pdf
C1753 05/17/18R
京公网安备 11010802033920号
EEWORLD
