EEWORLDEEWORLDEEWORLD

Part Number

Search

UTN-21.93OHMS0.01%

Description
Fixed Resistor, Wire Wound, 1.5W, 1.93ohm, 60V, 0.01% +/-Tol, 50ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size261KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

UTN-21.93OHMS0.01% Overview

Fixed Resistor, Wire Wound, 1.5W, 1.93ohm, 60V, 0.01% +/-Tol, 50ppm/Cel, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT

UTN-21.93OHMS0.01% Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7017805650
package instructionAXIAL LEADED, ROHS COMPLIANT
Reach Compliance Codecompliant
Country Of OriginIsrael
ECCN codeEAR99
YTEOL10
Other featuresNON INDUCTIVE
structureTubular
JESD-609 codee3
Lead diameter0.8 mm
Lead length25.4 mm
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature275 °C
Minimum operating temperature-55 °C
Package diameter4 mm
Package length8.9 mm
Package shapeTUBULAR PACKAGE
Package formAxial
Rated power dissipation(P)1.5 W
Rated temperature25 °C
resistance1.93 Ω
Resistor typeFIXED RESISTOR
surface mountNO
technologyWIRE WOUND
Temperature Coefficient50 ppm/°C
Terminal surfaceTin (Sn)
Terminal shapeWIRE
Tolerance0.01%
Operating Voltage60 V
UT Series
FEATURES
Resistances from 0.02 to 320kOhms
Power Rating 0.1 to 13Watts
Resistance Tolerances to ± 0.01%
Low TCR: ± 20ppm/K Standard
MIL-R-26 / MIL-R-39007 Power Ratings
Temperature Range: -55°C to +350°C (V)
Non-Inductive Windings Available
TABLE 1—SPECIFICATIONS
Tolerances
Temperature Coefficient
±0.01% to ±10% ( 1% Standard )
>10W : ±20ppm/K
1W to10W : ±50ppm/K
<1W : Call Factory
-55°C to +275°C : Characteristic U
-55°C to +350°C : Characteristic V
500 VAC : UT-1 / UT-1/2A / UT-1/2 / UT-1A
1000 VAC : All Others
Centerless ground ceramic core
Tinned copper or copperweld leads
High temperature / trivalent / inorganic Silicone coating
All welded terminations
Temperature Range
Dielectric Strength
Constuction
Environmental Performance
(MIL-STD 202)
DR
Characteristic U
±0.2% + 0.05W
±1% + 0.05W
±0.2% + 0.05W
±0.2% + 0.05W
±0.2% + 0.05W
±0.2% + 0.05W
±0.1% + 0.05W
±0.1% + 0.05W
Characteristic V
±0.2% + 0.05W
±3% + 0.05W
±2% + 0.05W
±2% + 0.05W
±2% + 0.05W
±2% + 0.05W
±0.2% + 0.05W
±0.2% + 0.05W
Dielectric
Load Life
Storage
Moisture Resistance
Thermal Shock
5X Overload ( 5s )
Shock
Vibration
FIGURE 1—DERATING
120
100
Power (%)
80
60
40
20
0
0
25
50
100 150 200 275
Ambient Temperature (°C)
300
350
Char V
Char U
ORDERING INFORMATION
Part Number - Resistance - Tolerance - TCR ( If not standard )
UT-5 25kOhms 0.1%
For Non-Inductive Windings / insert the letter “N” ( i.e. UTN-5 )
Document No.: 64327
Revision: 31-01-2015
For technical questions,
contact
powertron@vpgsensors.com
www.powertron.de
1
RS485 communication issues in MSP430F169
1. General framework: realize the communication between MCU and PC. The PC (USB interface) sends characters, which are converted to RS232 via USB, and then to RS485 via RS232, and then received by the...
灞波儿奔 Microcontroller MCU
Raspberry Pi PICO low-resolution thermal imager
Using the Raspberry Pi PICO and CircuitPython system, plus the AMG8833 sensor and TFT screen, you can make a thermal imager.Project website :https://www.recantha.co.uk/blog/?p=20959...
dcexpert MicroPython Open Source section
Reversible USB port
I bought a mobile power board a few days ago. I didn’t think much of it at first, but later I found that the USB A port was quite special. It can be plugged in both ways....
dcexpert Making friends through disassembly
Why does the power consumption of stm32L0 increase after it enters STOP mode again after being woken up by an external interrupt in STOP mode?
The power consumption of the first entry into stop mode is correct. After being woken up by an external interrupt, the power consumption of the next entry into stop mode is 300uA higher. What is going...
StruggleMySen stm32/stm8
[TI millimeter wave radar evaluation]_4_boost board evaluation encountered problems 2
[i=s]This post was last edited by wangran_95 on 2019-12-31 08:47[/i]After using the device, I found that it was hard to find a power supply. There were two boards and two power supplies, so I had to c...
wangran_95 TI Technology Forum
Using registers to do STM8 UART1 error request help
[i=s]This post was last edited by zhang520 on 2021-10-21 15:08[/i]Error[Li006]: duplicate definitions for "_interrupt_21"; Change 21 to 20 and the system will run fine...
zhang520 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号