D../CRCW....-HR
Vishay
Lead (Pb)-bearing Thick Film, Rectangular
High Value Chip Resistor
FEATURES
•
High resistance values (up to 470M)
•
Suitable for voltage dividers and hybrids
•
SnPb contacts on Ni barrier layer
•
Metal glaze on high quality ceramic
•
Protective overglaze
STANDARD ELECTRICAL SPECIFICATIONS
SIZE
POWER RATING LIMITING ELEMENT TEMP. COEFF. TOLERANCE RESISTANCE
E-SERIES
P
70 °C
W
VOLTAGE MAX. V≅
ppm/K
%
RANGE
Ω
INCH METRIC
±5
11M - 470M
24
D11/CRCW0603-HR 0603
1608
0.10
75
± 500
D12/CRCW0805-HR 0805
2012
0.125
150
± 500
±5
11M - 470M
24
D25/CRCW1206-HR 1206
3216
0.25
200
± 500
±5
11M - 470M
24
Notes
•
These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
•
Marking and packaging: See appropriate catalog or web pages
•
Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material
MODEL
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
W
Rated Dissipation at 70 °C
(2)
Limiting Element Voltage
V≅
Voltage Coefficient
%/V
> 100
> 300
Insulation Voltage (1 min)
V
peak
K/W
≤
550
≤
220
Thermal Resistance
(1)
Insulation Resistance
Ω
Category Temperature Range
°C
Weight/1000 pieces
g
2
10
Notes
(1)
Measuring conditions in acc. to EN 140401-802
(2)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
D11
CRCW0603-HR
0.1
75
D12
CRCW0805-HR
0.125
150
< 100M: < 0.1/> 100M: < 0.3
> 200
≤
440
> 10
9
- 55 to + 155
5.5
D25
CRCW1206-HR
0.25
200
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW060314M0JPTBHR
(3)
C
R
C
W
0
VALUE
M
= Million
6
0
3
1
4
M
0
J
TCR
P
T
B
H
R
SPECIAL
MODEL/SIZE
CRCW0603
CRCW0805
CRCW1206
TOLERANCE
J
=±5%
PACKAGING
(4)
TA, TB
TC, TI
TL
P
= ± 500 ppm/K
up to 2 digits
HR
= High Value
Product Description: CRCW0603 146 J 500 RT5
CRCW0603
MODEL
CRCW0603
CRCW0805
CRCW1206
(3)
(4)
146
RESISTANCE VALUE
686 = 68 MΩ
227 = 220 MΩ
± 5 % = 2 sig. digits plus multiplier
J
TOLERANCE
J=±5%
500
TCR
± 500 ppm/K
RT5
PACKAGING
(4)
RT1, RT5
RT6, RG1
R20
Notes
Preferred way for ordering products is by use of the PART NUMBER
Please refer to table PACKAGING, see next page
For technical questions, contact: filmresistors.thickfilmchip@vishay.com
Document Number: 20011
Revision: 13-Oct-08
www.vishay.com
159
D../CRCW....-HR
Lead (Pb)-bearing Thick Film, Rectangular
High Value Chip Resistor
PACKAGING
REEL
MODEL
PACKING CODE
TAPE WIDTH
DIAMETER
PITCH
PIECES/REEL
PART NUMBER
PAPER
180 mm/7"
D11/CRCW0603-HR
8 mm
285 mm/11.25"
330 mm/13"
180 mm/7"
D12/CRCW0805-HR
8 mm
285 mm/11.25"
330 mm/13"
180 mm/7"
D25/CRCW1206-HR
8 mm
285 mm/11.25"
330 mm/13"
4 mm
4 mm
4 mm
5000
10 000
20 000
5000
10 000
20 000
5000
10 000
20 000
TA
TB
TC
TA
TB
TC
TA
TB
TC
TL
TL
TI
TL
TI
BLISTER
TI
PRODUCT DESC.
PAPER
RT1
RT5
RT6
RT1
RT5
RT6
RT1
RT5
RT6
R20
R20
RG1
R20
RG1
BLISTER
RG1
Vishay
DIMENSIONS
SOLDER PAD DIMENSIONS
[in millimeters]
SIZE
INCH METRIC
0603
0805
1206
1608
2012
3216
L
1.55
2.0
3.2
+ 0.10
- 0.05
+ 0.20
- 0.10
+ 0.10
- 0.20
DIMENSIONS
[in millimeters]
REFLOW SOLDERING
W
0.85 ± 0.1
1.25 ± 0.15
1.6 ± 0.15
H
0.45 ± 0.05
0.45 ± 0.05
0.55 ± 0.05
T1
0.3 ± 0.2
0.3
+ 0.20
- 0.10
WAVE SOLDERING
a
0.9
0.9
1.1
b
0.9
1.3
1.7
l
1.0
1.3
2.3
T2
0.3 ± 0.2
0.3 ± 0.2
0.4 ± 0.2
a
0.5
0.7
0.9
b
0.9
1.3
1.7
l
1.0
1.2
2.0
0.45 ± 0.2
Temperature Rise in °C
80
70
60
50
40
0402 0603 0805
1206
Rated Power in
%
90
120
100
1210
80
60
40
2010
2512
30
1218
20
10
0
0
0.1
0.2
0.3
0.4
0.5
20
0
- 55
- 25
0
25
50
Temperature Rise
Power in W
Derating
75
70
100
125
155 175
Ambient Temperature in °C
Document Number: 20011
Revision: 13-Oct-08
For technical questions, contact: filmresistors.thickfilmchip@vishay.com
www.vishay.com
160
D../CRCW....-HR
Vishay
Lead (Pb)-bearing Thick Film, Rectangular
High Value Chip Resistor
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
REQUIREMENTS
PERMISSIBLE CHANGE (ΔR/R)
STABILITY CLASS 2 OR BETTER
Stability for product types:
D../CRCW...-HR
Resistance (4.5)
Temperature coefficient (4.8.4.2)
-
20/- 55/20 °C and
20/125/20 °C
U
= 2.5 x (P
70
x
R)
1/2
≤
2 x
U
max.
;
Duration: according the style
Aging 4 h at 155 °C, dryheat
solder bath method; 235 °C; 2 s
visual examination
Solder bath method;
(260 ± 5) °C; (10 ± 1) s
30 min at LCT = - 55 °C;
30 min at UCT = 125 °C; 5 cycles
(40 ± 2) °C; 56 days;
(93 ± 3) % RH
16 h at UCT = 125 °C; 1 cycle at 55 °C;
2 h at LCT = - 55 °C;
1 h/1 kPa at 15 °C to 35 °C;
5 cycles at 55 °C
U
= (P
70
×
R)
1/2
U
=
U
max.
; whichever is less severe
U
= (P
70
×
R)
1/2
U
=
U
max.
; whichever is less severe
1.5 h ON; 0.5 h OFF;
70 °C; 1000 h
Duration extended to 8000 h
UCT = 125 °C; 1000 h
±5%
± 500 ppm/K
±
(0.5
%
R
+ 0.05
Ω)
Good tinning
(≥ 95 % covered)
no visible damage
±
(0.5
%
R
+ 0.05
Ω)
±
(0.5
%
R
+ 0.05
Ω)
±
(2
%
R
+ 0.1
Ω)
11 MΩ to 470 MΩ
TEST (clause)
CONDITIONS OF TEST
Overload (4.13)
Solderability (4.17.5)
Resistance to soldering heat
(4.18.2)
Rapid change of temperature (4.19)
Damp heat, steady state (4.24)
Climatic sequence (4.23)
±
(2
%
R
+ 0.1
Ω)
Endurance at 70 °C (4.25.1)
±
(2
%
R
+ 0.1
Ω)
Extended endurance (4.25.1.8)
Endurance at upper category
temperature (4.25.3)
± (4 %
R
+ 0.1
Ω)
± (2 %
R
+ 0.1
Ω)
APPLICABLE SPECIFICATIONS
• EN 60115-1
• EN 140400
• EN 140401-802
• IEC 60068-2-x
• IEC 60286-3
Generic Specifications
Sectional Specification
Detail Specifications
Variety of environmental test procedures
Packaging of SMD components
www.vishay.com
161
For technical questions, contact: filmresistors.thickfilmchip@vishay.com
Document Number: 20011
Revision: 13-Oct-08
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 11-Mar-11
www.vishay.com
1
京公网安备 11010802033920号
EEWORLD
