SPECIFICATION
Liquid Crystal Display LC104S1-A1
NO.
-
-
-
1
2
3
3-1
3-2
3-3
3-4
3-5
3-6
4
4-1
4-2
5
6
7
7-1
7-2
8
8-1
8-2
9
10
COVER
CONTENTS
RECORD OF REVISIONS
GENERAL DESCRIPTION
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL SPECIFICATIONS
ITEM
Page
1
2
3
4
5
6
6
8
10
11
12
13
14
14
17
18
22
23
23
23
24
24
24
25
25
ELECTRICAL CHARACTREISTICS
INTERFACE CONNECTIONS
SIGNAL TIMING SPECIFICATIONS
SIGNAL TIMING WAVEFORMS
COLOR INPUT DATA REFERNECE
POWER SEQUENCE
OPTICAL SPECIFICATIONS
TRANSMISSIVE MODE
REFLECTIVE MODE
MECHANICAL CHARACTERISTICS
RELIABILITY
INTERNATIONAL STANDARDS
SAFETY
EMC
PACKING
DESIGNATION OF LOT MARK
PAKING FORM
PRECAUTIONS
INCOMING INSPECTION STANDARD
Alpha Point Ltd.
Vernissakatu 8A
01300 Vantaa, Finland
Tel.: +358-9-34
64 34 1
Fax: +358-9-34
64 34 2
Page 2 / 28
http://www.alpha.fi
SPECIFICATION
Liquid Crystal Display LC104S1-A1
RECORDS OF REVISIONS
Revision No
0.0
Revision No
Nov 30, 2001
Page
-
First Draft
DESCRIPTION
0.1
Jan 03, 2002
18, 20
Adjust maxium thickness(6.7mm)
Removes conductive tape at gate PCB
to improve ESD performance.
(refer to the page 20 for details.)
1.0
Jan 30, 2002
14
Remove the gamut ratio.
(because color coordinates are specified.)
Update the specifications.
(color coordinate and reflectance)
insert the definition of N and n in the 10.3
and 10.4 clauses.
insert the one note in the 10.4 clause.
17
28
Alpha Point Ltd.
Vernissakatu 8A
01300 Vantaa, Finland
Tel.: +358-9-34
64 34 1
Fax: +358-9-34
64 34 2
Page 3 / 28
http://www.alpha.fi
SPECIFICATION
Liquid Crystal Display LC104S1-A1
1. General Description
The
LC104S1-A1
is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent
Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element.
It is a transflective type
(1)
display operating in the normally white mode. This TFT-LCD has 10.4 inches
diagonally measured active display area with SVGA resolution(600 vertical by 800 horizontal pixel array)
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.
Gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot,
thus, presenting a palette of more than 262,144 colors.
The LC104S1-A1 has been designed to apply the interface method that enables low power. Flat Link
must be used as a LVDS(Low Voltage Differential Signaling) chip.
The LC104S1-A1 is intended to support applications where thin thickness, low power are critical factors
and graphic display are important. In combination with the vertical arrangement of the sub-pixels, the
LC104S1-A1 characteristics provide an excellent flat display for office automation products such as
Tough PC.
(ref. No. 1 : Transflective type means that has a function of transmissive and reflective mode in display and
display is visible indoor or outdoor under dark and sunlight at all.)
FlatLink interface
Timing
Control
Block
Row Driver circuit
Column driver circuit
CN1
TFT-LCD
(800 X 600)
Power
Block
CN
2
Backlight Ass’y
General Features
Active screen size
Outline Dimension
Pixel Pitch
Pixel format
Color depth
Luminance, white
Power Consumption
Weight
Display operating mode
Surface treatments
10.4 inches (26.4 cm) diagonal
224.5 (H) x 172.0 (V) x 6.1 (D) mm (Typ.) Pls refer to page 20 for details.
0.88 mm x RGB X 0.264mm
800 horiz. By 600 vert. Pixels (RGB stripes arrangement)
6-bit, about 262,144 colors
120 cd/m
2
(Typ.) (Transmissive only) , reflectance = 14%
0.9W logic (typ.) / 3.0W CCFL(1) (TYP.)
310g (Typ.)
320g (Max.)
Transflective mode, Normally White
Hard coating (3H) of the front polarizer
Anti-glare treatment of the rear polarizer
Alpha Point Ltd.
Vernissakatu 8A
01300 Vantaa, Finland
Tel.: +358-9-34
64 34 1
Fax: +358-9-34
64 34 2
Page 4 / 28
http://www.alpha.fi
SPECIFICATION
Liquid Crystal Display LC104S1-A1
2. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause operation or damage to the unit.
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameter
symbol
Min.
Power Input Voltage
Operating Temperature
Storage Temperature
Operating Ambient Humidity
Storage Humidity
V
CC
T
OP
T
ST
H
OP
H
ST
-0.3
0
-20
10
10
Values
Max.
4.0
50
60
90
90
Vdc
°C
°C
%RH
%RH
At 25 +/- 5°C
1
1
1
1
Units
Notes
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39
°C
Max, and no condensation of water.
90%
60
60%
Wet Bulb
Temperature [C]
40
30
20
10
0
10%
10
20
30
40
50
60
70
80
50
Humidity [(%)RH]
Storage
40%
Operation
-20
0
Dry Bulb Temperature [C]
Alpha Point Ltd.
Vernissakatu 8A
01300 Vantaa, Finland
Tel.: +358-9-34
64 34 1
Fax: +358-9-34
64 34 2
Page 5 / 28
http://www.alpha.fi
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
