performance oscillators utilize a proven silicon MEMS
technology to provide excellent jitter and stability over
a wide range of supply voltages and temperatures. By
eliminating the need for quartz or SAW technology,
MEMS oscillators significantly enhance reliability and
accelerate product development, while meeting
stringent clock performance criteria for a variety of
communications, storage, and networking applications.
DSC1101 has a standby feature that allows it to
completely power-down when EN pin is pulled low;
whereas for DSC1121, only the outputs are disabled
when EN is low. Both oscillators are available in
industry standard packages, including the small
2.5 mm x 2.0 mm, and are “drop-in” replacements for
standard 4-pin CMOS quartz crystal oscillators.
Functional Block Diagram
Applications
• Storage Area Networks
- SATA, SAS, Fibre Channel
• Passive Optical Networks
- EPON, 10G-EPON,V GPON, 10G-PON
• Ethernet
- 1G, 10GBASE-T/KR/LR/SR, and FCoE
• HD/SD/SDI Video and Surveillance
• PCI Express
• Display Port
2017 Microchip Technology Inc.
DS20005613B-page 1
DSC1101/21
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Input Voltage, V
IN
..............................................................................................................................–0.3V to V
DD
+ 0.3V
Supply Voltage .......................................................................................................................................... –0.3V to +4.0V
ESD Protection On All Pins ........................................................................................... 4000V HBM, 1500V CDM (max.)
† Notice:
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Note:
1000+ years of data retention on internal memory.
TABLE 1-1:
DC CHARACTERISTICS
Electrical Characteristics
Parameters
Supply Voltage (Note
1)
Sym.
V
DD
Min.
2.25
—
Supply Current
I
DD
—
—
Frequency Stability
(Including frequency
variations due to initial
tolerance, temp. and
power supply voltage.)
Aging
Startup Time (Note
2)
Input Logic Levels
Input Logic High
Input Logic Low
Output Disable Time
(Note
3)
Output Enable Time
Enable Pull-up Resistor
(Note
4)
CMOS Output
Output Logic Levels
Output Logic High
Output Logic Low
Note 1:
2:
3:
4:
V
OH
V
OL
0.9
V
DD
—
—
—
—
0.1
V
DD
V
I = ±6 mA
—
Typ.
—
—
20
31
—
—
—
—
—
—
—
—
—
—
40
Max.
3.6
0.095
22
35
±10
±20
—
—
—
—
0.75
V
DD
—
—
—
—
—
±25
±50
±5
5
—
0.1
V
DD
5
5
20
—
V
ns
ms
ns
k
—
—
DSC1101
DSC1121
Pull-up Resistor Exist
ppm
ms
ppm
mA
Units
V
—
DSC1101, EN pin low, output
is disabled
DSC1121, EN pin low, output
is disabled
Output enabled, C
L
= 15 pF,
F
0
= 100 MHz
Ext Comm. & Ind. only
All temp ranges
All temp ranges
All temp ranges
1 year @ 25°C
T = 25°C
Conditions
f
f
t
SU
V
IH
V
IL
t
DS
t
EN
—
Pin 6 V
DD
should be filtered with 0.1 µF capacitor.
t
SU
is time to 100 ppm of output frequency after V
DD
is applied and outputs are enabled.
Output Waveform and Test Circuit figures define the parameters.
Output is enabled if pad is floated or not connected.
DS20005613B-page 2
2017 Microchip Technology Inc.
DSC1101/21
TABLE 1-1:
DC CHARACTERISTICS (CONTINUED)
Electrical Characteristics
Parameters
Output Transition Time
Rise Time
Fall Time
Sym.
t
R
t
F
Min.
—
—
2.3
Frequency
f
0
3.3
Output Duty Cycle
Period Jitter
Integrated Phase Noise
SYM
J
PER
J
PH
45
—
—
—
—
Note 1:
2:
3:
4:
—
—
3
0.3
0.38
1.7
170
55
—
—
—
2
ps
RMS
%
ps
RMS
Typ.
1.1
1.3
—
Max.
2
2
170
MHz
ns
Units
Conditions
20% to 80%
C
L
= 15 pF
C
L
= 15 pF, –20°C to +70°C
and –40°C to +85°C
C
L
= 15 pF, –40°C to +105°C
and –55°C to +125°C
—
F
OUT
= 125 MHz
200 kHz to 20 MHz @ 125 MHz
100 kHz to 20 MHz @ 125 MHz
12 kHz to 20 MHz @ 125 MHz
Pin 6 V
DD
should be filtered with 0.1 µF capacitor.
t
SU
is time to 100 ppm of output frequency after V
DD
is applied and outputs are enabled.
Output Waveform and Test Circuit figures define the parameters.
Output is enabled if pad is floated or not connected.
2017 Microchip Technology Inc.
DS20005613B-page 3
DSC1101/21
TEMPERATURE SPECIFICATIONS (Note
1)
Parameters
Temperature Ranges
T
A
Operating Temperature Range (T)
T
A
T
A
T
A
Junction Operating Temperature
Storage Temperature Range
Soldering Temperature Range
Note 1:
T
J
T
A
T
S
–20
–40
–40
–55
—
–40
—
—
—
—
—
—
—
—
+70
+85
+105
+125
+150
+150
+260
°C
°C
°C
°C
°C
°C
°C
Ordering Option E
Ordering Option I
Ordering Option L
Ordering Option M
—
—
40 sec. max
Sym.
Min.
Typ.
Max.
Units
Conditions
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., T
A
, T
J
,
JA
). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability.
DS20005613B-page 4
2017 Microchip Technology Inc.
DSC1101/21
2.0
Note:
NOMINAL PERFORMANCE CURVES
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Is there any big guy who works on MEMS or sensors? Please take me tothis article. This content is originally created by EEWORLD forum netizen Nie Yongzhong . If you want to reprint or use it for comme...
Leakage current and withstand voltage test of low voltage battery productsBattery-powered products like wristbands, mobile phones, and headphones. Charging is DC5V. How to use leakage current tester a...
BMS insulation detection circuitWhen the insulation resistance between the total positive terminal PACK+of the battery pack and the vehicle ground decreases in proportion to the insulation resistance ...
In the field of chip design, using silicon-proven IP is a proven practice.事实上，这种既能节省时间又能提高质量的复杂片上系统(SoC)开发方法的使用范围越来越广，普及率越来越高。特别是在高速增长的动态细分市场中，基于IP的设计已被证明是一种可以显著缩短开发时间、确保输出更高质量的产品、以及提高工程人员工作效率的手段，便于工程...
The need for isolation in 48 V automotive applications continues to grow. This is a compact, efficient, robust, low noise method to isolate 48 V systems via the CAN interface.Designing for cars is a b...
The interference current on the power line is divided into two categories according to its flow path: one is differential mode interference current and the other is common mode interference current...[Details]
Power electronics technology is a modern technology that uses power electronic devices to transform and control electric energy. It can save energy by 10% to 40%, reduce the size of electromechan...[Details]
MAX97200 II headphone amplifier effectively extends audio playback time in portable devices
New amplifier provides high-quality audio output while effectively extending audio playback time
SUNNY...[Details]
According to feedback from netizens at IT Home, Xiaomi Mi 6 has made new progress in flashing Ubuntu Touch recently. Developers have brought new updates to the Ubuntu version of Xiaomi Mi 6, includin...[Details]
With the rapid iteration of software and hardware technology levels such as automotive chips, voice interaction, and automotive systems, the automotive cockpit has entered the intelligent stage, wi...[Details]
Preface, the origin of writing this article
Recently, when I was studying Wei Dongshan's embedded training video (Practical Project 3: USB Camera Monitoring), when configuring the dhcp source ...[Details]
1. Introduction In power plants and substations, the DC power supplied to the secondary circuit is called electric operating power. The electric operating power supply is mainly used to supply power...[Details]
The continuous improvement of semiconductor design and manufacturing process technology has made the devices on the circuit board run faster and smaller. The power supply system requires more types of...[Details]
On the morning of August 26, a screenshot of a test product said to be a 6.7-inch iPhone 12 Pro Max was exposed on the Internet today. According to this picture, this year's iPhone flagship product...[Details]
According to the Information Agency, U.S. renewable energy generation doubled from 382 MWh in 2008 to 742 million MWh in 2018.
During the same period, solar power generation increased from 2 m...[Details]
introduction
At present, there are two new technologies for reversing: ultrasonic ranging and rear-view camera.
Reversing radar and rear-view camera have their own advantages and disadvant...[Details]
OFweek Cup · OFweek 2023 China
Robot
Industry Annual Selection (abbreviated as OFweek Robot Awards 2023) is jointly organized by OFweek, China's high-tech industry portal, and its authorita...[Details]
Source program: SLAVR737.ASM uses AVR microcontroller 8-bit data to generate random numbers, outputs random numbers from PORTA and PORTC, and displays them on 8X8 LEDs. For hardware wiring circuit, s...[Details]
The vehicle-mounted GPS navigation system is an important application of automotive electronics. As cars enter ordinary households and quickly become popular, the demand for vehicle-mounted GPS is als...[Details]
01
Information security requirements
This chapter mainly introduces the information security requirements from four aspects: hardware security, system security, communication security, an...[Details]
DIY/Open Source Hardware
京公网安备 11010802033920号
EEWORLD
