Standard Frequencies – see Page 5 for common frequencies.
* Check with factory for availability of frequencies not listed.
Applications
IoT and IIoT Applications
Wireless Communications
FPGA/Microcontrollers
USB Interfaces
Computer Peripherals
Portable Equipment
Test and Measurement
M2M Communications
Broadband Access
Description
CTS Model 407 incorporates a high Q quartz resonator and is ideal for supporting a wide range of commercial and
industrial applications.
Ordering Information
Model
407
Mode of
O s ci l l a ti on
F
Tol era nce
@ +25°C
3
Tem pera ture Sta bi l i ty/Tem pera ture Ra ng e
5
Loa d
Ca pa ci ta nce
D
F requency
[ MHz ]
XXXMXXXX
Mode
Code
Fundamental
F
3rd Overtone
T
Code
- 20°C
1
X
2
3
5
Code
1
X
2
3
Tolerance
±10ppm
±15ppm
±20ppm
±30ppm
Stability Code
to +70°C - 30°C
±10ppm
R
±15ppm
Y
±20ppm
N
±30ppm
4
±50ppm
8
Stability Code
to +85°C - 40°C
±10ppm
-
±15ppm
W
±20ppm
6
±30ppm
7
±50ppm
9
Stability
to +85°C
-
±15ppm
±20ppm
±30ppm
±50ppm
Code
Frequency
1
Frequency
Code Capacitance Code Capacitance
8pF
18pF
K
D
9pF
20pF
J
E
10pF
24pF
A
F
12pF
30pF
L
G
16pF
Series
C
S
Notes:
1] Frequency is recorded with 3 leading digits before the "M" and 4 significant digits after the "M" [including zeroes]. (Ex. XXXMXXXX [016M3840],
There are frequencies with significant digits after the "M" that exceed the 4 digits. The remaining digits will be truncated from the CTS part
number, but the factory will calibrate to the full frequency desired. Examples below; P/N Frequency = Actual Frequency
13M5537 = 13.553750MHz
14M3181 = 14.318180MHz
16M6666 = 16.666670MHz
28M6363 = 28.636360MHz
N ot a l l perf orm a nce com bi na ti ons a nd f requenci es m a y be a va i l a bl e.
Conta ct your l oca l CTS Repres enta ti ve or CTS Cus tom e r Servi ce f or a va i l a bi l i ty.
This product is specified for use only in standard commercial applications. Supplier disclaims all express and implied warranties and liability in connection with any use of this
product in any non-commercial applications or in any application that may expose the product to conditions that are outside of the tolerances provided in its specification.
The circuit schematic is shown above. There are several types of input signals, as shown below:
1. Sinusoidal AC signal with frequency f=470KHz and Vpp=19.6V
2. Sinusoidal AC signal with frequency f=3...
After successfully installing Simplicity Studio V5, I still took a lot of detours and spent a few days. The main reason was probably that the network in the environment was not very good, which was pr...
1. After downloading the provided QT file, put it in the folder /home/topeet/opencv2.4.9/opencvinstall/. Enter the /QT/demo directory. Let's open the opencv_pic.pro project.Ubuntu# vi opencv_pic.proNo...
To be honest, after playing with several domestic chips, I really like the AT32 chip. Not only can the RAM be expanded at will, but when I was soldering the sample board, I soldered the MCU upside dow...
LED display scanning method: the difference between static and dynamic
The "point-to-point" control from the output pin of the driver IC to the pixel is called static drive, and the "point-to-...[Details]
0 Introduction
As people's living standards improve, the consumption structure has undergone tremendous changes, and the proportion of consumer spending on entertainment in total spending is c...[Details]
Not long ago, CATL released a 4C lithium iron phosphate battery named Shenxing Battery. 4C is not difficult to understand. It means 4 times the charging speed. It only takes 1/4 of 1 hour to fully ...[Details]
A floating isolation oscilloscope is an oscilloscope that can measure floating signals and is isolated between channels (no need to share a reference ground). For example, if the potential differen...[Details]
In recent years, as the global automobile market has reached a turning point and entered an era of low growth, many traditional auto giants have not only "banded together for warmth" to survive the "...[Details]
1. Independent watchdog The independent watchdog of STM32 is driven by an internal 40kHz low-speed clock. Even if the main clock fails, it is still effective. It should be noted that the clock of th...[Details]
Use 89S51 stand-alone P1^0 to output 1KHZ and 500HZ audio signals. 1KHZ signal is required to sound for 100ms, 500HZ signal is required to sound for 200ms alternately. P1^7 is connected to a switch fo...[Details]
In the process of R&D and testing of new energy vehicles, some performance parameter tests such as ripple current/voltage have not been taken seriously by manufacturers in the past, but they are cr...[Details]
On March 2, 2021, a digital blogger revealed that Wu Dezhuo, president of ByteDance's New Stone Lab, had resigned and joined Sharklet. In response, Wu Dezhuo said the revelation was true. Wu Dezhou...[Details]
Low noise amplifiers (LNAs) are critical in separating the signal from the noise in a communications receiver. There are other techniques for controlling noise within the system, including fil...[Details]
In the past data acquisition systems, microcontrollers and DSPs were often selected as the main controllers. However, with the continuous improvement of FPGA performance, it has the advantages of high...[Details]
News from Qianjiang today showed that the underground foundation construction of Hubei Dinglong Holding Co., Ltd.'s 500,000-piece/year integrated circuit CMP polishing pad project has been completed....[Details]
Example 1: Define PB0 as output, and the output is high level
DDRB=BIT(0); //define PB0 as output
PORTB|=BIT(0); // PB0 outputs high level
Example 2: Define PB0 and PB1 as outputs, an...[Details]
During Electronica, ON Semiconductor CEO Hassane El-Khoury was interviewed by Power Electronics News at the exhibition site, detailing the new 65nm BCD that ON Semiconductor brought and its future ...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
