EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

14930FAGLFX13501KA

Description
Potentiometer, Cermet, 1W, 500ohm, 10% +/-Tol, -150,150ppm/Cel, 4935,
CategoryPassive components    The resistor   
File Size148KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

14930FAGLFX13501KA Overview

Potentiometer, Cermet, 1W, 500ohm, 10% +/-Tol, -150,150ppm/Cel, 4935,

14930FAGLFX13501KA Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid967777890
Reach Compliance Codecompliant
Country Of OriginCzechia
YTEOL7.45
structureTrimmer Pot
JESD-609 codee3
Lead length8.85 mm
Maximum operating temperature125 °C
Minimum operating temperature-40 °C
Package height13.1 mm
Package length12.5 mm
Package formPCB Mount
Package width8.83 mm
method of packingBox
Rated power dissipation(P)1 W
resistance500 Ω
Resistor typePOTENTIOMETER
rotation angle270 deg
series149
size code4935
technologyCERMET
Temperature Coefficient150 ppm/°C
Terminal surfaceTin (Sn)
Tolerance10%
Interface corresponding to SNVS_TAMPER3 signal
A: Please tell me which GPIO the SNVS_TAMPER3 signal on the IMX6UL corresponds to and which document should I look at? The GPIO is not marked in the core board interface diagram. B: WIKI search http:/...
明远智睿Lan Industrial Control Electronics
nRF52832-QFAA Hardware Reference Design
[align=left][color=#333333][font=微软雅黑][size=2]Manufacturer: NORDIC[/size][/font][/color][/align][align=left][color=#333333][font=微软雅黑][font=微软雅黑][size=2]Package/Casing: QPN48[/size][/font][/font][/col...
乐乐熊 RF/Wirelessly
How to design the MCU+8266 program structure
I have a project that I did on GD32F450, similar to ST's F427, using the freertos+HAL library generated by CUBE. There are two main tasks. The Main task is to use the signal converted from AC power as...
yup1983 Embedded System
Why does TIM1_CH3N not output PWM after configuring PWM in STM32F103C8T6?
Why does TIM1_CH3N not output PWM after configuring PWM in STM32F103C8T6?...
tanyanbang Motor Drive Control(Motor Control)
Please advise on the PinMux code
According to "Adding Flash Read and Write to an Existing mmWave Project", the code snippet is as follows: /* Setup the PINMUX to bring out the QSPI */ Pinmux_Set_OverrideCtrl(SOC_XWR14XX_PINR10_PADAP,...
davidjune TI Technology Forum
Can you recommend a chip that can boost 3.3V to 5V?
I am a newbie and I really don't know much about this. Could you please recommend a chip that can boost 3.3V to 5V, preferably one with higher efficiency?...
乐乐老了 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号