Features .......................................................................................................................................................................................1
Ordering Information .....................................................................................................................................................................2
Dimensions and Patterns ― 3.2 x 2.5 mm .................................................................................................................................14
Dimensions and Patterns ― 5.0 x 3.2 mm .................................................................................................................................14
Dimensions and Patterns ― 7.0 x 5.0 mm .................................................................................................................................15
Additional Information .................................................................................................................................................................16
Revision History ..........................................................................................................................................................................17
Rev 1.07
Page 3 of 17
www.sitime.com
SiT3373
220 MHz to 725 MHz Ultra-low Jitter Differential VCXO
Electrical Characteristics
Table 2. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with standard
output termination shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
220.000001
-15
-25
-35
-50
Operating Temperature Range
T_use
-20
-40
-40
-40
Supply Voltage
Vdd
2.97
2.70
2.52
2.25
Pull Range
Upper Control Voltage
Lower Control Voltage
Control Voltage Input Impedance
Control Voltage Input Bandwidth
Pull Range Linearity
Frequency Change Polarity
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Start-up Time
OE Enable/Disable Time
PR
VC_U
VC_L
VC_z
V_c
Lin
–
VIH
VIL
Z_in
DC
T_start
T_oe
70%
–
–
45
–
–
Typ.
–
–
–
–
–
–
–
–
–
3.30
3.00
2.80
2.50
Max.
725
+15
+25
+35
+50
+70
+85
+95
+105
Supply Voltage
3.63
3.30
3.08
2.75
V
V
V
V
ppm
Vdd
Vdd
MΩ
kHz
%
–
–
30%
-
55
3.0
3.8
Vdd
Vdd
kΩ
%
ms
µs
Measured from the time Vdd reaches its rated minimum value.
f = 322.265625 MHz. Measured from the time OE pin reaches
rated VIH and VIL to the time clock pins reach 90% of swing
and high-Z. See
Figure 9
and
Figure 10
Pin 2, OE
Pin 2, OE
Pin 2, OE logic high or logic low
Contact SiTime
for other input bandwidth options
See the APR (Absolute Pull Range)
Table 11.
Contact SiTime
for custom pull range options
Voltage at which maximum frequency deviation is guaranteed
Voltage at which minimum frequency deviation is guaranteed
Unit
MHz
ppm
ppm
ppm
ppm
°C
°C
°C
°C
Extended Industrial
Extended Commercial
Industrial
Condition
Accurate to 6 decimal places
Inclusive of initial tolerance, operating temperature, rated
power supply voltage, load variations, and first year aging
at 25°C, with VIN voltage at Vdd/2.
±15
ppm is only guaranteed for pull range up to
±100
ppm.
Frequency Range
Frequency Stability
Temperature Range
Voltage Control Characteristics
±25, ±50, ±80, ±100, ±150, ±200,
±400, ±800, ±1600, ±3200
90%
–
–
–
–
–
–
10
10
–
Positive Slope
–
–
100
–
–
–
–
10%
–
–
1.0
Input Characteristics
Output Characteristics
Startup and OE Timing
Rev 1.07
Page 4 of 17
www.sitime.com
SiT3373
220 MHz to 725 MHz Ultra-low Jitter Differential VCXO
Table 3. Electrical Characteristics – LVPECL Specific
Parameter
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
RMS Period Jitter
[4]
RMS Phase Jitter (random)
Symbol
Idd
I_OE
I_leak
I_driver
VOH
VOL
V_Swing
Tr, Tf
T_jitt
T_phj
–
0.220
0.270
ps
Min.
–
–
–
–
Vdd-1.15
Vdd-1.9
1.2
–
–
Typ.
–
–
0.15
–
–
–
1.6
225
1.0
Max.
97
63
–
32
Vdd-0.7
Vdd-1.5
2.0
290
1.6
Unit
mA
mA
A
mA
V
V
V
ps
ps
Condition
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
f = 322.265625 MHz, Vdd = 3.3 V or 2.5 V
f = 322.265625 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels, includes spurs, pull range =
±100
ppm.
Temperature ranges -20 to 70°C and -40 to 85°C
f = 322.265625 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels, includes spurs, pull range =
±100
ppm.
Temperature ranges -40 to 95°C and -40 to 105°C
f = 156.25 or 322.265625 MHz, IEEE802.3-2005 10 GbE jitter
mask integration bandwidth = 1.875 MHz to 20 MHz,
all Vdd levels
f = 322.265625 MHz, Vdd = 3.3 V or 2.5 V
f = 322.265625 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels, includes spurs, pull range =
±100
ppm.
Temperature ranges -20 to 70°C and -40 to 85°C
f = 322.265625 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels, includes spurs, pull range =
±100
ppm.
Temperature ranges -40 to 95°C and -40 to 105°C
f = 322.265625 MHz, IEEE802.3-2005 10 GbE jitter mask
integration bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
[i=s]This post was last edited by 90houyidai on 2022-6-5 23:27[/i]Project name: [ RVB2601 Creative Application Development] + Music SpectrumAuthor: 90houyidaiProject BackgroundRVB2601 uses Pingtouge's...
[i=s]This post was last edited by shihengrui on 2019-6-23 00:11[/i]GD32E231 DIY Contest——Summary of the Gizwits Timer Switch projectshihengrui@EEWORLD1. Project Name:
Gizwits Timer Switch2. Project In...
As a PCB engineer with style and pursuit, how can you draw a neat, efficient and reliable PCB diagram? PCB design seems complicated. It is necessary to consider the direction of various signals and th...
The detection circuit diagram is posted here. The DC voltage value is 500V. R20, R26, R27, R28 and Rx form a sampling resistor between DC+, GND and DC-. The purpose is to collect the voltage across R2...
Design requirements:#
Using DC motor as fan
The keyboard can adjust the fan speed
Design Overview:
According to the design requirements, the fan needs to be turned o...[Details]
Failure Mode and Effects Analysis (DFMEA) plays a very important role in the automotive industry. In the process of automotive design and manufacturing, DFMEA is widely used to identify and manage ...[Details]
1. Introduction
In recent years, the characteristics of LED light sources, such as high efficiency, long life, and green environmental protection, have been recognized and valued by peo...[Details]
Lightning strike is a natural phenomenon, but it may cause great property loss and personal injury to human life. Therefore, in urban construction, relatively high and metal buildings and public faci...[Details]
Simulation results:
"Figure 16: Transfer curve of jitter amplifier circuit"
(X-axis: input jitter; Y-axis: output jitter)
The most important component in the built-in jitter test architecture...[Details]
Introduction: This paper introduces a design of a digital wireless temperature sensor based on Atmel's single-chip microcomputer ATmega324p as the control core, combined with the digital temperature ...[Details]
The tuning fork liquid level switch is mainly used to realize the upper and lower limit alarm and control of the liquid level. It is widely used in many industrial automation control fields such as...[Details]
It has been two months since I bought the board. At first, I wanted to run it naked, but the projects were all under ADS, which couldn't be used on the win7 system. So I thought about running it on M...[Details]
As LEDs become more popular as a way to save power for general lighting, methods to drive them efficiently have become essential. For example, Luxeon devices from Lumileds provide lighting effects or ...[Details]
Digital image processing technology has been widely used in the fields of electronic communication and information processing. Designing a video signal acquisition circuit that is flexible in functio...[Details]
"The joy of free movement" and "realizing a colorful and sustainable society" are the slogans put forward at this Honda Technology Conference. At the Honda Research Institute in Tochigi Prefecture, J...[Details]
Infineon Technologies Launches New MOTIX™ Motor Gate Driver IC
Easily migrate from 12 V to 48 V systems while fully meeting functional safety requirements
Infineon Tech...[Details]
1. P1 is a quasi-bidirectional port. Each bit can be used separately. When a bit is used as an input line, the latch of the bit must be '1'; when used as an input, it can be driven by any TTL circu...[Details]
1. The oscilloscope must be calibrated and compensated before use. Calibration is mainly to optimize the current measurement value and not be affected by the external temperature environment. The ca...[Details]
The source program of the PIC series microcontroller refers to the program written by the mnemonic instructions of the PIC (assembly language program). Here we will briefly introduce the format requir...[Details]
XuanTie RISC-V Activity Zone
京公网安备 11010802033920号
EEWORLD
