^For symbol “U” termination add 0.020 inch (0.51mm) to the positive length tolerance and 0.015 inches (0.38mm) to the positive width and thickness tolerances.
Ordering Information
DSCC Drawing
Number
03028 (0603 case size)
03028
BX
Dielectric
BR
BX
Capacitance
Code (pF)
2 Sig. Digits +
Number of
Zeros
104
Y
Voltage
W = 6.3V
X = 10V
Y = 16V
Z = 25V
A = 50V
B = 100V
C = 200V
Capacitance
Tolerance
J = ±5%
K = ±10%
M = ±20%
J
End
Metallization^
U = SnPb (4% min)
Z = SnPb (4% min)
Z
Blank = No group C testing
C = Full group C
L = 2,000 hour life test only
M = 1,000 hour life test only
H = Low voltage humidity only
Group C
Testing Option
C
Blank = Bulk Bag
Packaging/Grade
(C-Spec)*
7189
7246 = Anti-Static Bulk Bag
7292 = Waffle Pack
7189 = 7” Reel Marked
^ “U” = Base metallization-barrier metal-solder coated (tin/lead alloy, with a min of 4% lead). Melting point is +200ºC or less. Metallization thickness is ≥ 60µ-inches.
^ “Z” = Base metallization-barrier metal-tinned (tin/lead alloy, with a min of 4% lead).
* Additional reeling or packaging options may be available. Contact KEMET for details.
Additional termination options may be available. Contact KEMET for details.
A “Packaging C-Spec” is a 4-digit numeric code which identifies the packaging type. When ordering, the proper code must be included in the 15th through 18th
character positions of the ordering code. See “Ordering Information” section of this document for further details. Product ordered without a “Packaging C-Spec” will
default to our standard “Bulk Bag” packaging.
2
A “Packaging C-spec” (see note
1
above) is not required for “Bulk Bag” packaging (excluding Anti-Static Bulk Bag). The 15th through 18th character positions of
the ordering code should be left blank. All product ordered without a “Packaging C-Spec” will default to our standard “Bulk Bag” packaging.
Soldering Process
Marking
All parts incorporate the standard KEMET barrier layer of pure nickel with a tin-lead (SnPb) finish. Both “U” and “Z” termination finishes
contain a minimum of 4% lead.
Marking is not available for DSCC approved EIA 0603 case size capacitors. These chips will be supplied unmarked.
[size=4] The clock problem of MSP430 has always been vague, and I always forget it, so I decided to write this article to help me remember. The following content is all referenced to online materials ...
The serpentine line is a routing method often used in the PCB wiring process. Its main purpose is to adjust the delay and meet the system timing design requirements. However, every PCB design engineer...
The company has made a car side turn signal light, the circuit is very simple, now when the power is off, the ground of the static gun is connected to the product input ground, when 4KV static electri...
Let's look at some more pictures of cute animals! They're so animated and adorable I can't help it! This project uses PyPortal's ESP32 WiFi processor to retrieve images from a repository of cat, dog, ...
Analysis of several effective switching power supply electromagnetic interference suppression Regarding the research on switching power supply EMI (Electro-Magnetic Interference), some studies st...[Details]
1 Introduction
Touch is an important form of perception for robots to obtain environmental information, second only to vision. It is an essential medium for robots to interact directly wi...[Details]
PWM generation principle: The general timer can use the GPIO pin for pulse output. When configured as comparison output and PWM output function, the capture/compare register TIMx_CCR is used as the ...[Details]
Traditionally, PFC (power factor correction) offline power converters are designed with two power stages: The first power stage is usually a boost converter, because in this topology there is a con...[Details]
The anti-theft alarm system is a system that uses physical methods or electronic technology to automatically detect intrusions that occur in the defense monitoring area, generate alarm signals, and...[Details]
1. Millisecond delay
Delay 1ms;
void delay_1ms(void)
{
unsigned int i;
for(i=1;i (unsigned int)(xtal*143-2);i++)
;
}
In the above formula, xtal is the crystal frequency in MHz.
...[Details]
On July 15, 2021, under the guidance of the China Integrated Circuit Design Innovation Alliance (ICDIA), the Open NPU Innovation Alliance (ONIA) was officially established, jointly initiated by Tsing...[Details]
With the progress of automobile industry and electronic technology, the number of on-board electrical equipment is increasing day by day. Traffic police vehicles have put forward new requirements f...[Details]
The TCL Huizhou Electronic Information Industry Base project is located in Shuikou Street, Huicheng District, with an investment of 3 billion yuan. The project aims to build a high-end electronic inf...[Details]
DS18B20 is a single bus digital temperature sensor with a test temperature range of -55℃-125℃. It has the characteristics of small size, low hardware cost, strong anti-interference ability and high p...[Details]
Central topics: * Input circuit failure * Photocoupler failure * PWM IC and peripheral circuit failure * Other power supply component failure With the rapid development of medical e...[Details]
On the evening of April 18, Shengong Co., Ltd. disclosed its 2020 annual report. During the reporting period, the company achieved annual operating income of 192 million yuan, a year-on-year increase...[Details]
PIC16C7X (Except 710/71/711) When ADCON1 is configured to set all analog pins as digital I/O, VREF is internally tied to ground. This causes the ADRES register to read 0xFF every time an analog conver...[Details]
On October 23, we learned from the official that Ideal Intelligent Driving "end-to-end + VLM" has officially started full push, including all models under the AD MAX platform. The new generation of...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
