Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
A heart rate monitoring solution based on the MSP430 LaunchPad Value Line Development Kit ( MSP-EXP430G2 ), which uses the MSP430G2xx microcontroller (MCU). The electrocardiogram (EKG) signal is sampl...
Research report on the evaluation of the international competitiveness of China's electronic information industryNews Publisher: Release Date: 2006-6-7 Viewed 83 times1. Research Background Over the ...
Author: Lucien KUANG, ST engineer
Click to download the pdf document to view:Keywords: DTM, BlueNRGQuestion: Customers often ask me how to use your DTM and what functions it has.
ST engineer's answer:...
[i=s]This post was last edited by CQU_ZMY on 2022-10-20 00:27[/i]Hey guys, I recently made a single-power-supply common-phase amplifier circuit, the circuit diagram is as follows. When the power suppl...
Hardware engineers, do you know how to solve differential equations? When I just graduated and was looking for a job, I was interviewed by a company as a hardware engineer. Among the interview questio...
On September 24, Leyard said in an institutional survey that Lijing's products are divided into two categories, one is backlight products for notebooks and pads, and the other is self-luminous comme...[Details]
Poly builds a one-stop office collaboration SaaS ecosystem, joins hands with Tencent Cloud and Tencent Meeting to create a new intelligent collaborative office scenario in China At the "Smart Meeti...[Details]
On December 24, the State Grid Chongqing Electric Power Company's cloud platform, data middle platform, and Internet of Things management platform were launched for trial operation, and the company...[Details]
The biggest feature that distinguishes a stepper motor from other control-purpose motors is that it can accept digital control signals (electric pulse signals) and convert them into corresponding a...[Details]
According to foreign media reports, Daimler R&D chief Markus Schaefer said that Mercedes-Benz plans to build complete electric drivetrains for its new MMA and MB.EA electric vehicle architectures com...[Details]
On the evening of May 9, Huacan Optoelectronics issued an announcement stating that as of the date of this announcement, Zhuhai Huafa Real Industry Investment Holding Co., Ltd. (hereinafter referred ...[Details]
STM8 has won the favor of many companies with its low cost and high cost performance. Due to the needs of convenience and security in products, IAP download is often used to upgrade the software of c...[Details]
1 Introduction
With the application of microelectronics technology and modern control theory in AC variable frequency speed regulation systems, the performance of frequency converters (or inve...[Details]
Currently, most car head-up displays project information to the bottom of the windshield when they are working, whether they are original or third-party products. But accessory manufacturer DD...[Details]
How to use an oscilloscope 1. Obtaining a baseline: When the operator is using an oscilloscope without an instruction manual, he must first obtain a thin horizontal baseline before using the probe to...[Details]
1. Introduction
In order to reduce the pollution of internal switching power supplies of office automation equipment, computers and household appliances to the power grid, the International El...[Details]
overview
The goal of this project is to design an efficient power system with digitally adjustable output voltage (VOUT). To ensure the accuracy of the output voltage, a digital closed-loo...[Details]
September 20, 2024, Tessenderlo, Belgium -
Melexis, a global microelectronics engineering company, announces the addition of the MLX92253 to its Hall-effect dual latch product family.
This
...[Details]
Yesterday (20th), Google was forced by the US government's "ban" to announce the suspension of some of its support for Huawei's business. Reuters analysis said that this move will result in Huawei sm...[Details]
In automotive power systems, damage to DC-DC converters can be caused by a variety of factors. However, one of the main reasons is that the residual voltage of the surge TVS (overvoltage protector)...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
