NEW
MS type Lower Profile Plug
H/MS Series
Circular connector conforming to MIL-C-5015
PAT.P
Connector Height Comparison
18-10 Size
50.1mm
45.5mm
3057-10
70mm
54.5mm
Existing MS Connector
Lower-profile Plug
22-22 Size
48.2mm
53.2mm
s
Features
1. 20% Height Reduction
When compared with existing H/MS Series connectors
the overall height of plug assemblies is lower, allowing it
to be used in space constrained applications.
78.7mm
41mm
3057-12
60.7mm
2. Cable Exit in 360° Directions
The cable can exit in any of the 8 fixed direction, in 45°
increments.
Existing MS Connector
Lower-profile Plug
3. Simple Assembly
The 2-piece design consisting of the contact/insulator
assembly and the back-shell assembly allows termination
without the use of any specialized tools.
Cable Exit Direction of 360°
4. Water and Dust Protection
IP 67 rating when fully terminated and mated with
corresponding part.
5. TUV Certification
Provided with a protective circuit function for TUV
certification. The (D) pin is directly connected to the
outside metal case.
s
Applications
Factory automation equipment, robotic equipment, servo
motors, and a wide variety of industrial and measuring
instruments.
Plug
°
(45
)
Can be changed
in 45 degree increments
45.8mm
63.8mm
56.5mm
18
22
3057-10
3057-12
2009.2
1
H/MS SeriesqMS type Lower Profile Plug
sProduct
Specifications
Voltage rating
250VAC, 250V DC (pollution degree: 3, overvoltage category:
3)
500V AC, 500V DC (pollution degree: 2, overvoltage category:
2)
Current rating
23A Max. (18-10 size)
46A Max. (22-22 size)
Operating temperature range
-25ç to +125ç
Storage temperature range
-25ç to +125ç
Rating
Item
Specification
18-10 size
22-22 size
Conditions
1A DC
500 V DC
2250V AC/one minute.
Frequency: 10 to 500 Hz, single amplitude of 0.75 mm,
acceleration of 98 m/s
2
for 3 hours in 3 axis.
Acceleration of 490 m/s
2
, 11ms duration, sine half-wave
waveform, 3 cycles in each of the 3 axis.
1. Contact resistance
3 m ohms max.
1 m ohms max.
2. Insulation resistance 5000 M ohms min.
3. Withstanding voltage No flashover or insulation breakdown.
4. Vibration
No electrical discontinuity for 10 ms max.
5. Shock
Contact resistance:
Contact resistance:
6. Durability
500 cycles
4.5 m ohms max.
1.5 m ohms max.
(insertion/ withdrawal)
Temperature: -55ç
➝
Room temperature to +125ç
➝
Room
Insulation resistance: 5000 M ohms min.
7. Temperature cycle
temperature Time: 30
➝
10 to 15
➝
30
➝
10 to 15 (Minutes)
5 cycles.
Insulation resistance: 50 M ohms min. (Humidity state)
8. Humidity
96 hours at temperature of 71ç and humidity of 95% .
500 M ohms min. (Dry state)
9. Water/dust
No dust penetration.
When mated with corresponding connector.
protection
No water penetration when submerged for 0.5 hour at the depth of 1 meter.
sMaterials
Item
Body
Insulator
Socket Contacts
Gasket
Bushing
Material
Aluminum alloy
PPS
Copper alloy
Silicone Rubber
Chloroprene rubber
Finish
Black chromate
Color: Black
Silver plating
Color: Black
Color: Black
Remarks
-------------------
UL94V-0
-------------------
-------------------
-------------------
s
Additional Product Information
1. Product number suffixes
(10) Supplied with a wire hole in the locking ring (to prevent loosening of the ring).
(11) Supplied without the wire hole in the locking ring.
2. Corresponding receptacles.
18-10 Size: Part number H/MS3102A18-10P-D-T1(10)
22-22 Size: Part number H/MS3102A22-22P-D-T(10)
2
H/MS SeriesqMS type Lower Profile Plug
sPlug
H/MS08A18-10S-DT10D(73)
41
A
Ø33.5
D
B
18-10S
C
X
45.5
Part Number
H/MS08A18-10S-DT10D(73)
H/MS08A18-10S-DT10D1(73)
CL No.
120-0476-3-73
120-0481-3-73
Number of Contacts
4
Weight
89g
Applicable Cable Diameter Contact solder pot inner diameter RoHS
Ø12~Ø14.3mm
Ø10~Ø12.5mm
2.5mm
YES
H/MS08A18-10S-DT10C(74)
Ø33.5
35.5
Part Number
H/MS08A18-10S-DT10C(74)
CL No.
120-0480-0-74
Number of Contacts
4
Weight
77.6g
Applicable Cable Diameter Contact solder pot inner diameter RoHS
Ø13~Ø14.3mm
2.5mm
YES
H/MS08A22-22S-DT12D(73)
A
D
Ø39.5
53.2
Part Number
H/MS08A22-22S-DT12D(73)
H/MS08A22-22S-DT12D(74)
H/MS08A22-22S-DT12D1(73)
H/MS08A22-22S-DT12D1(74)
CL No.
120-0477-6-73
120-0477-6-74
120-0482-6-73
120-0482-6-74
Number of Contacts
Weight
Applicable Cable Diameter Contact solder pot inner diameter RoHS
Ø13~Ø15.9mm
4
127g
Ø10~Ø13.5mm
3057-10
31
Shown one type.
41
A
D
B
18-10S
C
X
Ø30
Shown one type.
45.8
22-22S
X
B
C
3057-12
36
Shown one type.
4.5mm
YES
3
H/MS SeriesqMS type Lower Profile Plug
B
Assembly Procedures
Process
Outline of assembly
B
B
A
Pre-solder
Conductor portion
A
Contacts
Back-shell
B
Solder
Bushing
1
Insulator/contact assembly
Washer
A
18-10 Size
22-22 Size
24mm
33mm
B
13mm
15mm
Strain relief clamp
a. Pass the strain relief clamp, washer, bushing, and hood over the cable, in this order.
b. Prepare the cable and conductors per the dimensions in Table 1.
c. Bend the exposed conductor to the B dimension as indicated in Table 1.
d. Pre-solder the exposed conductor and solder it as shown to the exposed contact.
Note: Use care not to damage the conductor’s insulation.
4.5 mm min.
Strain relief clamp
Screw
Back-shell
Set screw
(Hexagonal hole opposite side 1.27 mm)
3057-10
Locking ring
Table 2
2
Locking Ring
3 to 3.5N • m
Cable Clamp
5 to 6N • m
a. Place over the contact/insulator assembly (in the following order:Back shell, bushing, washer, strain relief clamp).
b. Tighten the Locking ring and Cable clamp to the torque values per Table 2.
c. Tighten the set screw to a torque value of 0.3-0.4 N-m
HRS recommended tool: PB205/1.27 (CL150-0066-3)or equivalent.
d. Using screwdriver tighten the two strain relief clamp screws until both sides of the moveable part are in contact with the cable clamp.
®
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN
PHONE: 81-3-3491-5300, FAX: 81-3-3495-5230
http://www.hirose.com
http://www.hirose-connectors.com
4
The contents of this catalog are current as of date of 02/2009. Contents are subject to change without notice for the purpose of improvements.
30
57
Table 1
-10
Cable
Cable
Clamp
Washer
Bushing
_pdf/pg_0001.png)
京公网安备 11010802033920号
EEWORLD_pdf/1.png)
_pdf/2.png)
_pdf/3.png)
_pdf/4.png)
_pdf/pg_0002.png)
_pdf/pg_0003.png)
_pdf/pg_0004.png)
