This quality assurance specification establishes the quality standard for a low fire
hazard (LFH), heat-shrinkable identification sleeving for use in applications where
low fire hazard characteristics are critical. These special requirements are detailed
in Table 7.
HX Low Fire Hazard sleeving meets Rail Standard EN45545-2 requirement set R22/R23
Hazard rating 3. This requirement set and hazard rating allows unlimited use of this
product with any rail car design and operating category in Europe.
The operating temperature for this product is -55° to + 105°
C
C.
This system is an automatic method of identifying items by printing a mark onto a sleeve.
The mark is permanent upon printing. This system is not recommended where strain relief
properties are required.
The marker shall be fabricated from cross linked polyolefin tubing, flattened and then
mounted on a carrier as HX-SCE, HX or supplied as flattened spooled continuous tube as
HXCT.
The marker system comprises specific printers and ribbons. Compliance to this
specification can only be guaranteed if TE Connectivity approved printers and ribbons are
used. This information can be found in TE document 411-121005 ‘Printer Product Ribbon
Matrix Document’.
Unless specified, the tube size for qualification testing is 6.4mm.
Approved Signatories:
This document is electronically reviewed and approved by TE Connectivity.
TE CONNECTIVITY, SWINDON, UK
While TE Connectivity has made every reasonable effort to ensure the accuracy of the information in this specification, TE Connectivity does not guarantee that it is error-
free, nor does TE Connectivity make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE Connectivity reserves
the right to make any adjustments to the information contained herein at any time without notice. TE Connectivity expressly disclaims all implied warranties regarding the
information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are
for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE Connectivity for the latest
dimensions and design specifications.
If this document is printed it becomes uncontrolled.
RW-2072 Issue 13
Page 2 of 27
October 2014
1.
SCOPE
The tests in this specification, as made on HX products, define the nature of a low fire hazard product
for cable identification. Test procedures have been selected based on the ability of that test to provide
key flammability data which can be used by an engineer to give a valid fire risk assessment of an
installation based on actual use.
This qualification standard will establish whether fit form and function of the finished product meets
product design expectations.
The flammability performance criteria has been modelled to reflect the current requirements of the
global rail market. The key performance indicators of flamability, smoke and toxicity have been
selected based on there ability to highlight any changes in performance.
2.
2.1
REQUIREMENTS
Composition, appearance and color
The sleeving shall be fabricated from low fire hazard (LFH), irradiated, thermally stabilized modified
polyolefin compound. It shall be homogeneous and essentially free from flaws, defects, pinholes,
bubbles, seams, cracks or inclusions.
The markers shall be White or Yellow unless otherwise specified.
Dimensions
The product shall be supplied in one of the following formats:
• HX-SCE - as shown in figure 1 and to the dimensions of table 1.
• HXCT - continuous tubing to the dimensions of table 2
• HX - as shown in figure 2 and figure 3 and to the dimensions of table 3
2.2
TE CONNECTIVITY, SWINDON, UK
While TE Connectivity has made every reasonable effort to ensure the accuracy of the information in this specification, TE Connectivity does not guarantee that it is error-
free, nor does TE Connectivity make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE Connectivity reserves
the right to make any adjustments to the information contained herein at any time without notice. TE Connectivity expressly disclaims all implied warranties regarding the
information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are
for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE Connectivity for the latest
dimensions and design specifications.
If this document is printed it becomes uncontrolled.
RW-2072 Issue 13
Page 3 of 27
October 2014
Table 1: HX-SCE Dimensions
Part
Description
Minimum
Supplied Inside
Diameter
mm (inches)
2.4 (0.094)
3.2 (0.126)
4.8 (0.189)
6.4 (0.250)
9.5 (0.375)
12.7 (0.500)
19.0 (0.750)
25.4 (1.0)
38.1 (1.5)
50.8 (2.0)
Maximum
Recovered
Inside Diameter
mm (inches)
1.19 (0.047)
1.6 (0.063)
2.4 (0.094)
3.2 (0.126)
4.8 (0.189)
6.4 (0.250)
9.5 (0.375)
12.7 (0.50)
19.1 (0.75)
25.4 (1.00)
Wall Thickness
after Recovery
mm (inches)
0.50 ± 0.10
(0.020 ± 0.004)
0.50 ± 0.10
(0.020 ± 0.004)
0.51 ± 0.11
(0.020 ± 0.004)
0.65 ± 0.15
(0.026 ± 0.006)
0.65 ± 0.15
(0.026 ± 0.006)
0.65 ± 0.15
(0.026 ± 0.006)
0.75 ± 0.15
(0.030 ± 0.006)
0.90 ± 0.15
(0.035 ± 0.006)
1.00 ± 0.20
(0.039 ± 0.008)
1.00 ± 0.20
(0.039 ± 0.008)
Minimum
Sleeve Width
mm (inches)
4.3 (0.17)
6.5 (0.26)
8.9 (0.32)
11.0 (0.43)
15.7 (0.62)
20.7 (0.81)
30.7 (1.21)
41.1 (1.62)
61.0 (2.40)
80.0 (3.15)
Sleeve
Progression
mm (inches)
12.70 ± 0.63
(0.500 ± 0.025)
12.70 ± 0.63
(0.500 ± 0.025)
12.70 ± 0.76
(0.500 ± 0.030)
16.94 ± 0.89
(0.667 ± 0.035)
25.40 ± 0.89
(1.000 ± 0.035)
29.64 ± 1.02
(1.167 ± 0.040)
42.34 ± 1.02
(1.667 ± 0.040)
50.80 ± 1.02
(2.000 ± 0.040)
72.00 ± 1.02
(2.833 ± 0.040)
101.60 ± 1.02
(2.833 ± 0.040)
Nominal Weight of
single sleeve
(~50mm long)
grams
0.21
0.26
0.37
0.62
0.87
1.13
1.90
3.02
4.96
6.51
HX-SCE-2.4
HX-SCE-3.2
HX-SCE-4.8
HX-SCE-6.4
HX-SCE-9.5
HX-SCE-12.7
HX-SCE-19.0
HX-SCE-25.4
HX-SCE-38.1
HX-SCE-50.8
Table 2: HXCT Dimensions
Minimum
Supplied Inside
Diameter
mm (inches)
2.4 (0.094)
3.2 (0.126)
4.8 (0.189)
6.4 (0.250)
9.5 (0.375)
12.7 (0.500)
19.0 (0.750)
25.4 (1.0)
38.1 (1.5)
Maximum
Recovered
Inside Diameter
mm (inches)
1.19 (0.047)
1.6 (0.063)
2.4 (0.094)
3.2 (0.126)
4.8 (0.189)
6.4 (0.250)
9.5 (0.375)
12.7 (0.50)
19.1 (0.75)
Wall Thickness
After Recovery
mm (inches)
0.50 ± 0.10
(0.020 ± 0.004)
0.50 ± 0.10
(0.020 ± 0.004)
0.51 ± 0.11
(0.020 ± 0.004)
0.65 ± 0.15
(0.026 ± 0.006)
0.65 ± 0.15
(0.026 ± 0.006)
0.65 ± 0.15
(0.026 ± 0.006)
0.75 ± 0.15
(0.030 ± 0.006)
0.90 ± 0.15
(0.035 ± 0.006)
1.00 ± 0.20
(0.039 ± 0.008)
Minimum
Sleeve Width
mm (inches)
4.3 (0.17)
6.5 (0.26)
8.9 (0.32)
11.0 (0.43)
15.7 (0.62)
20.7 (0.81)
30.7 (1.21)
41.1 (1.62)
61.0 (2.40)
Nominal
Weight of single
sleeve (~50mm long)
grams
0.21
0.26
0.37
0.62
0.87
1.13
1.90
3.02
4.96
Part
Description
HXCT-2.4
HXCT-3.2
HXCT-4.8
HXCT-6.4
HXCT-9.5
HXCT-12.7
HXCT-19.0
HXCT-25.4
HXCT-38.1
TE CONNECTIVITY, SWINDON, UK
While TE Connectivity has made every reasonable effort to ensure the accuracy of the information in this specification, TE Connectivity does not guarantee that it is error-
free, nor does TE Connectivity make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE Connectivity reserves
the right to make any adjustments to the information contained herein at any time without notice. TE Connectivity expressly disclaims all implied warranties regarding the
information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are
for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE Connectivity for the latest
dimensions and design specifications.
If this document is printed it becomes uncontrolled.
RW-2072 Issue 13
Page 4 of 27
October 2014
Table 3: HX Dimensions
Minimum
Supplied Inside
Diameter
mm (inches)
3.2 (0.126)
4.8 (0.189)
6.4 (0.250)
9.5 (0.375)
12.7 (0.500)
19.0 (0.750)
25.4 (1.0)
38.1 (1.5)
Maximum
Recovered
Inside Diameter
mm (inches)
1.6 (0.063)
2.4 (0.094)
3.2 (0.126)
4.8 (0.189)
6.4 (0.250)
9.5 (0.375)
12.7 (0.50)
19.1 (0.75)
Wall Thickness
After Recovery
mm (inches)
0.50 ± 0.1
(0.02 ± 0.004)
0.51 ± 0.11
(0.02 ± 0.004)
0.65 ± 0.15
(0.026 ± 0.006)
0.65 ± 0.15
(0.026 ± 0.006)
0.65 ± 0.15
(0.026 ± 0.006)
0.75 ± 0.15
(0.030 ± 0.006)
0.90 ± 0.15
(0.035 ± 0.006)
1.00 ± 0.20
(0.039 ± 0.008)
Minimum
Sleeve Width
mm (inches)
6.5 (0.26)
8.9 (0.32)
11.0 (0.43)
15.7 (0.62)
20.7 (0.81)
30.7 (1.21)
41.1 (1.62)
61.0 (2.40)
Sleeve
Progression
mm (inches)
12.7 ± 0.5
(0.50 ± 0.02)
12.7 ± 0.5
(0.50 ± 0.02)
25.4 ± 0.5
(1.00 ± 0.02)
25.4 ± 0.5
(1.00 ± 0.02)
50.8 ± 0.5
(2.00 ± 0.02)
50.8 ± 0.5
(2.00 ± 0.02)
50.8 ± 0.5
(2.00 ± 0.02)
127 ± 0.5
(5.00 ± 0.02)
Nominal Weight
of single sleeve
(~50mm long)
grams
0.26
0.37
0.62
0.87
1.13
1.90
3.02
4.96
Part
Description
HX032
HX048
HX064
HX095
HX127
HX190
HX254
HX381
TE CONNECTIVITY, SWINDON, UK
While TE Connectivity has made every reasonable effort to ensure the accuracy of the information in this specification, TE Connectivity does not guarantee that it is error-
free, nor does TE Connectivity make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE Connectivity reserves
the right to make any adjustments to the information contained herein at any time without notice. TE Connectivity expressly disclaims all implied warranties regarding the
information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are
for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE Connectivity for the latest
dimensions and design specifications.
If this document is printed it becomes uncontrolled.
RW-2072 Issue 13
Page 5 of 27
October 2014
Figure 1. HX-SCE format
80.52 ± 1.52
(3.170 ± 0.060)
50.00 MINIMUM
(1.970)
4.83 ± 0.25
(0.190 ± 0.010)
TYPICALlY
3.05 (0.120)
SLEEVE
WIDTH
TYPICALLY
12.70
(0.500)
38.10 ± 0.25
(1.500 ± 0.010)
SLEEVE
PROGRESSION
DIAMETER
4.01 ± 0.13
(0.158 ± 0.005)
CARRIER
Dimensions in mm (inch).
TE CONNECTIVITY, SWINDON, UK
While TE Connectivity has made every reasonable effort to ensure the accuracy of the information in this specification, TE Connectivity does not guarantee that it is error-
free, nor does TE Connectivity make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE Connectivity reserves
the right to make any adjustments to the information contained herein at any time without notice. TE Connectivity expressly disclaims all implied warranties regarding the
information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this document are
for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE Connectivity for the latest
dimensions and design specifications.
If this document is printed it becomes uncontrolled.
It is probably to generate a PWM wave of a certain frequency through the clock
Using FPGA can get a more perfect waveform, but if only a CLK wave is provided, F5529LP can do it completely.
#include ms...
I want to learn about the multiplier part, but I can't find the multiplier part in the routine of the development board. I have opened every routine and still can't find the multiplier. Is there any r...
I use quaratus2 to do waveform simulation. There is no problem with compilation and code, but the waveform cannot be simulated. It prompts the error code: Error: (vsim_3170) Could not find 'work.PPQ_v...
Let me post a photo first. The board has been soldered with pin headers and sockets. In order to adapt to the Arduino Uno expansion board in my hand, I chose to solder the female socket. By the way, I...
[font=微软雅黑, "][size=14px][color=#000000][size=3]1.3 The Kalman Filter Algorithm[/size] [size=2]In this section, we will describe the Kalman filter derived from Dr Kalman. The following description wil...
Analogic
Tech
has announced the launch of the AAT282X active matrix thin-film
transistor
(TFT)
liquid crystal
display
(
LCD
) DC/DC converter product gr...[Details]
The function of the frequency divider:
In a speaker system, people call the cabinet, frequency division circuit and speaker unit the three major parts of the speaker system, and the frequency di...[Details]
In June 2019, Cambridge University released the AI Panorama Report. Part of the content can be found in the article "Cambridge 2019 AI Panorama Report Focuses on China and Takes Stock of Global AI ...[Details]
When I first learned about microcontrollers, like many novices, I was very confused and anxious. I was not sure whether I could learn it, and if so, how long it would take. But in the end I succeeded...[Details]
When it comes to the biggest advancement in mobile phone products in recent years, in addition to 5G, it is undoubtedly the high refresh rate screen. The high refresh rate can bring huge improv...[Details]
Aiming at the characteristics and shortcomings of winter heating system in northern my country, an indoor intelligent temperature control system based on embedded system ARM-Linux platform and fuzz...[Details]
BICS and Mavenir Collaborate to Launch VoLTE Solution to Enable Roaming Interoperability after 2G/3G Network Deprecation
Solution helps bridge the digital divide between ...[Details]
1. Introduction to stepper motors: In industrial control systems, it is usually necessary to control the translation and rotation of mechanical parts. Most of these mechanical parts are driven by AC m...[Details]
Electrostatic voltmeter is a commonly used pressure instrument , which is used in many industries. When using electrostatic voltage pressure gauge, users need to know the usage knowledge, which is ver...[Details]
Analyzing Intel's system-level foundry model
Compared with traditional foundries, Intel Foundry Services provides more services besides manufacturing silicon wafers for customers.
...[Details]
New energy vehicles refer to vehicles that use unconventional automotive fuels as their power source (or use conventional automotive fuels and adopt new on-board power devices), and integrate advance...[Details]
Today, Hesai announced that it has obtained the ISO/SAE 21434 automotive network security management system certification issued by the internationally authoritative third-party testing and certific...[Details]
Jiwei.com reported on April 20 that today, the Honor Play 5T Vitality Edition was officially launched on the Honor Mall, providing a 6+128GB storage version, priced at 1,299 yuan. Reservations are no...[Details]
The United States has added Huawei to the export control blacklist, and the U.S.-China trade dispute has expanded from a tariff war to a technology war. Scholars believe that compared with raising ta...[Details]
On October 14, the Yunnan Provincial Development and Reform Commission and the Yunnan Provincial Energy Bureau issued the "Yunnan Province 2024 Second Batch of New Energy Project Development and Const...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
