Ordering Information .................................................................................................................................................................... 2
7.1. User Programming Interface ..................................................................................................................................... 19
7.2. Start-up output frequency and signaling types .......................................................................................................... 19
8.1. Any-frequency function ............................................................................................................................................. 20
9 I C/SPI Control Registers...................................................................................................................................................... 30
9.1. Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 30
9.2. Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 31
9.3. Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 32
9.4. Register Address: 0x03. Flac-N PLL Integer Value and Flac-N PLL Fraction MSW ................................................. 33
9.6. Register Address: 0x05. PostDiv, Driver Control ...................................................................................................... 34
9.7. Register Address: 0x06. mDriver, Driver Control ...................................................................................................... 35
2
10 I C Operation ........................................................................................................................................................................ 36
2
10.1. I C protocol ............................................................................................................................................................... 36
2
10.2. I C Timing Specification ............................................................................................................................................ 38
2
10.3. I C Device Address Modes ....................................................................................................................................... 39
Dimensions and Patterns ........................................................................................................................................................... 46
Additional Information ................................................................................................................................................................ 47
Revision History ......................................................................................................................................................................... 48
Rev 0.91
Page 3 of 48
www.sitime.com
SiT3522
340 to 725 MHz Elite™ I
2
C/SPI Programmable Oscillator
1 Electrical Characteristics
PRELIMINARY
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
340.000001
340.000001
Typ.
–
–
Max.
725.000000
500.000000
Unit
MHz
MHz
Condition
LVDS and LVPECL output driver, factory or user
programmable, accurate to 6 decimal places
HCSL output driver, factory or user programmable, accurate to
6 decimal places
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-20
-20
-25
-50
First Year Aging
Operating Temperature Range
F_1y
T_use
–
-20
-40
-40
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
VIH
VIL
Z_in
DC
T_start
T_oe_hw
70%
–
–
45
–
–
–
–
–
–
±1
–
–
–
3.3
3.0
2.8
2.5
–
–
100
–
–
–
+20
+20
+25
+50
–
+70
+85
+105
Supply Voltage
3.63
3.3
3.08
2.75
–
30%
–
55
3.0
9.1
V
V
V
V
Vdd
Vdd
kΩ
%
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
OE pin
OE pin
OE pin, logic high or logic low
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1 -year aging at 25°C
Extended Commercial
Industrial
Extended Industrial. Available only for I C operation, not SPI.
2
st
Temperature Range
Input Characteristics – OE Pin
Output Characteristics
Startup and Output Enable/Disable Timing
T_oe_sw
–
–
11.8
µs
Rev 0.91
Page 4 of 48
www.sitime.com
SiT3522
340 to 725 MHz Elite™ I
2
C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
PRELIMINARY
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.10
–
94
63
–
30
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3V or 2.5V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B
T_jitt
–
0.22
0.075
0.23
0.09
1
0.260
0.085
0.325
0.095
1.6
ps
ps
ps
ps
ps
f = 622.08 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 622.08, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 622.08 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 622.08, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 622.08 MHz, Vdd = 3.3V or 2.5V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
89
67
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3V or 2.5V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
340
530
50
1.375
50
460
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.060
0.21
0.070
1
0.255
0.070
0.320
0.80
1.6
ps
ps
ps
ps
ps
f = 622.08 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 622.08 MHz, IEEE802.3-2005 10 GbE jitter mask
integration bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 622.08 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 622.08 MHz, IEEE802.3-2005 10 GbE jitter mask
integration bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 622.08 MHz, Vdd = 3.3V or 2.5V
mV
mV
V
mV
ps
f = 622.08 MHz. See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
[size=4] TMS320C6711 is a 32-bit floating-point DSP of TI's TMS320C6000 series. It has a CPU with dedicated hardware logic, on-chip memory, and on-chip peripherals, and supports separate or mixed prog...
SDK development environmentThe previous section explains how to use the configuration file. Now let's take a look at how to use the SDK to develop TI's mmWave sensor kit.First, enter the directory of ...
[align=left][color=rgb(65, 65, 65)][font=微软雅黑][size=4]Zhongjing Electronics (002579)) continues to accelerate its horizontal integration in the printed circuit board industry (PCB). After completing t...
How can the TM4c129 series MCU use the EPI general mode to communicate with the FPGA? How can I achieve address mapping like DSP and FPGA for read and write control? Please help me, thank you! !...
Before buying a cable fault tester, you must know about its manufacturer. After finding a better one for a long time, you can also buy a very suitable cable fault tester. Therefore, you must understan...
Due to the recent cold wave and snowstorm in the United States, Samsung Electronics' wafer factory in Austin, Texas, was short of electricity and had to be temporarily closed. It is reported that S...[Details]
1) Initialization of IIC: reset IIC, enable IIC clock unit, set corresponding I0 port to IIC function, clear acknowledge bit, start bit, interrupt bit, IIC enable bit, set IIC transmission rate, if i...[Details]
In order to summarize the learning experience of PIC16F616 microcontroller some time ago and facilitate communication, I wrote this article about the learning experience of PIC microcontroller, which...[Details]
Well-known whistleblower Yogesh Brar recently shared information about the Pixel 7 series. He said that the Pixel 7 series will not have a significant upgrade in camera specifications over its...[Details]
Preface
The clutch release bearing, also known as the release bearing, is an important component in the manual transmission system of the car. It plays a vital role in the engagement and disen...[Details]
Children's Day is coming soon. Have you not chosen a gift for your little prince or princess? A children's smart watch would be a good choice. As an important branch of smart wearable devices, chil...[Details]
Synopsys Virtualizer Development Toolkit enables software development up to 18 months before silicon is available and enables migration of testing from physical to virtual environments Synopsys and...[Details]
1. Huawei HarmonyOS Smart Cockpit
Equipped models: Seres new models
At this year's Huawei Developer Conference 2021 (Together), the "HarmonyOS Smart Cockpit" made its debut.
...[Details]
Overview Applications that measure light with photomultiplier tubes usually require the use of a picoammeter because the currents to be measured are very small. A photomultiplier tube (PMT) is a devi...[Details]
Security is becoming increasingly important in a variety of applications including smartphone accessories, smart meters, personal health monitoring, remote controls, and access systems. To protect r...[Details]
X-FAB, a leading analog foundry company, and Pineje, a domestic SiC power device supplier, have reached a long-term strategic cooperation to jointly promote the development of the global SiC indu...[Details]
As energy consumption gradually decreases, new energy sources are becoming a new hot spot. As a new type of energy that can be used, solar energy has attracted the attention of the world. The key poi...[Details]
Recently, Microsoft released an official statement, saying that it will abandon support for Microsoft Cortana on iOS and Android, and the last support time will end on January 31, 2020. In addition, ...[Details]
Plastic is a very important material, which is widely used in industrial and civil fields. In the field of connectors, plastic is a material that is widely used. It is used to produce housings, ins...[Details]
The multi-frequency display power supply circuit refers to a display that supports several video standards. The multi-frequency display can receive signal frequency values from multiple video adapt...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
