EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

232-180-KBW

Description
Fixed Resistor, Wire Wound, 3W, 18ohm, 60V, 10% +/-Tol, 20ppm/Cel,
CategoryPassive components    The resistor   
File Size41KB,1 Pages
ManufacturerRCD Components Inc.
Websitehttp://www.rcdcomponents.com/
Environmental Compliance
Download Datasheet Parametric View All

232-180-KBW Overview

Fixed Resistor, Wire Wound, 3W, 18ohm, 60V, 10% +/-Tol, 20ppm/Cel,

232-180-KBW Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid261484606
Reach Compliance Codecompliant
Country Of OriginMainland China, Saint Lucia, USA
YTEOL6.9
structureTubular
JESD-609 codee3
Lead diameter0.8 mm
Lead length31.75 mm
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature275 °C
Minimum operating temperature-55 °C
Package diameter3.56 mm
Package length8.9 mm
Package shapeCYLINDRICAL PACKAGE
Package formAxial
method of packingBulk
Rated power dissipation(P)3 W
Rated temperature25 °C
resistance18 Ω
Resistor typeFIXED RESISTOR
surface mountNO
technologyWIRE WOUND
Temperature Coefficient20 ppm/°C
Terminal surfaceMatte Tin (Sn)
Terminal shapeWIRE
Tolerance10%
Operating Voltage60 V
Reversible USB port
I bought a mobile power board a few days ago. I didn’t think much of it at first, but later I found that the USB A port was quite special. It can be plugged in both ways....
dcexpert Making friends through disassembly
TMS320F28335DSP principle and development programming
This book introduces the basic structure, working principle, application configuration and sample programs of the TMS320F28335 DSP chip newly launched by TI. The book has 13 chapters. Chapter 1 is an ...
fish001 DSP and ARM Processors
Why does the power consumption of stm32L0 increase after it enters STOP mode again after being woken up by an external interrupt in STOP mode?
The power consumption of the first entry into stop mode is correct. After being woken up by an external interrupt, the power consumption of the next entry into stop mode is 300uA higher. What is going...
StruggleMySen stm32/stm8
[TI millimeter wave radar evaluation]_4_boost board evaluation encountered problems 2
[i=s]This post was last edited by wangran_95 on 2019-12-31 08:47[/i]After using the device, I found that it was hard to find a power supply. There were two boards and two power supplies, so I had to c...
wangran_95 TI Technology Forum
Using registers to do STM8 UART1 error request help
[i=s]This post was last edited by zhang520 on 2021-10-21 15:08[/i]Error[Li006]: duplicate definitions for "_interrupt_21"; Change 21 to 20 and the system will run fine...
zhang520 stm32/stm8
XP power management issues
There is no "Enable Advanced Power Management" item in my mind. What is the reason and how to solve it? Before I came here to ask questions, I tried the following methods but they didn't work: 1. In t...
zbz0529 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号