EEWORLDEEWORLDEEWORLD

Part Number

Search

177-710-5-69P4K5-18RTG

Description
D Microminiature Connector, 69 Contact(s), Male, Plug,
CategoryThe connector    The connector   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

177-710-5-69P4K5-18RTG Overview

D Microminiature Connector, 69 Contact(s), Male, Plug,

177-710-5-69P4K5-18RTG Parametric

Parameter NameAttribute value
Objectid7004462012
Reach Compliance Codeunknown
ECCN codeEAR99
YTEOL8.5
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
body width0.351 inch
subject depth0.462 inch
body length1.735 inch
Body/casing typePLUG
Cable typeM22759/11
Connector typeD MICROMINIATURE CONNECTOR
Contactor designPREASSEM CONN
Contact point genderMALE
contact modeSTAGGERED
Contact resistance8 mΩ
Contact styleRND PIN-SKT
DIN complianceNO
Dielectric withstand voltage600VAC V
empty shellNO
Filter functionNO
IEC complianceNO
Insulation resistance5000000000 Ω
insulator materialLIQUID CRYSTAL POLYMER/POLYPHENYLENE SULFIDE
MIL complianceYES
Plug contact pitch0.05 inch
Match contact row spacing0.05 inch
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation option 1HOLE .096
Installation option 2LOCKING
Installation typeCABLE AND PANEL
Number of connectorsONE
Number of rows loaded3
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
OptionsWITH CABLE ASSEMBLY
Plating thickness50u inch
Rated current (signal)3 A
GuidelineMIL
Shell surfaceGOLD
Shell materialALUMINIUM
Termination typeWIRE
Total number of contacts69
Maximum wire diameter24 AWG
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
Brief analysis of three detection methods for faulty cables
[size=4] The initial detection method of the faulty cable is divided into the loop bridge balance method, the low-voltage pulse reflection method, and the flash tester method. In the cable fault initi...
fish001 Analogue and Mixed Signal
How to write software I2C for HC32F460
I ported the BMP180 program from STM32, but the software IIC has not responded. I tried the hardware IIC_start function but it failed. Can anyone give me some ideas and examples? Tell me the pitfalls ...
121315L Domestic Chip Exchange
Sound detection system
# Sound Detection System##Sound Detection System###The sound detection system is used to capture sound and display the time domain graph and spectrum graph of the sound. The interface of the detection...
bqgup Innovation Lab
What is an API? What is an SPI?
Programming Interface is an application program interface, while SPI is a service provider interface.In JDK, it is described as follows:· the API is the description of classes/interfaces/methods/... t...
火辣西米秀 Microcontroller MCU
Problems with the function of zero-crossing detection circuit
For example, using zero-crossing detection and adjusting the speed of a soymilk machine The speed and power output of the soymilk machine are different at different grinding stages. If the 220V AC pow...
shaorc Analog electronics
ST MEMS Device Resource Library-Other Application Documents
ST MEMS Device Resource Library: Click to enterOther application documents: Here we provide a wealth of introductions to MEMS device-related applications, algorithms, etc....
nmg MEMS sensors

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号