Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
The host SPI sends a group of numbers, such as A[]={"123456"}; theslave SPI receives it using interrupts, and each data can be completely sent out, but the interrupt can only receive 12, and the other...
BlueNrg-1 is used as a slave device, and Raspberry Pi is used as a master device. Raspberry Pi can successfully connect to BlueNrg-1 device. BlueNrg-1 can correctly receive the data sent by Raspberry ...
In DSP 28335, I sample four times in one cycle. Logically, the values of the four samples should be different, but the values of the four numbers in the ADCRESULT register are the same (). Why is this...
Direct reasons for fuse blowing in switching power supply: switch tube\power thick moduleectifier diode breakdown\100uf/400v large capacitor breakdown leakage, demagnetization resistor internal fragme...
C6Accel is an algorithm package that includes many signal processing and mathematical calculations. It provides a series of APIs that can be called by ARM-side programs. C6Accel complies with TI's xDA...
[size=4][color=#000000][backcolor=white] Usually, the CAN communication protocol only regulates the competition order when multiple devices send instructions on the bus at the same time, but rarely in...
Recently, the Orami team is committed to creating Orami offline voice solutions, which will be gradually applied to smart buildings, smart cars and other aspects. Olamie offline voice solution can ...[Details]
According to Science and Technology Daily, recently, Zhichi Huaxin (Wuxi) Sensing Technology Co., Ltd. (hereinafter referred to as "Zhichi Huaxin") and the Shanghai Institute of Microsystem and Infor...[Details]
In the aerospace equipment test, gyroscope and accelerometer test is an indispensable and important part. With the improvement of the accuracy level of gyroscope and accelerometer, the accuracy req...[Details]
1. Pay attention to regular calibration and testing
Toxic and harmful gas detectors, like other analytical detection instruments, are measured by relative comparison methods: first, ...[Details]
In his latest report, TF International analyst Ming-Chi Kuo pointed out that the Samsung Galaxy S11 to be released by Samsung in the first quarter of next year may be the world's first mobile phone w...[Details]
What is AEB?
AEB is the abbreviation of Automatic Emergency Braking, which means "automatic emergency braking" in Chinese. This technology can be said to be the "fuse" of the current intelligentiza...[Details]
The method described in this article is not necessarily correct, but it is very simple. You can definitely do it by following the instructions.
You can definitely get ...[Details]
The temperature characteristics of digital potentiometers differ from those of traditional mechanical potentiometers. The effects of temperature on the absolute resistance of the potentiometer must be...[Details]
Microcontrollers have been widely used in many modern electronic designs and productions, but there are still many inconveniences in the communication between microcontrollers. Common ones include ...[Details]
1 Introduction
In most measurement and control systems, temperature is an essential detection quantity, and temperature sensors are also very important sensor devices in measurement and co...[Details]
In 2023, all walks of life will start a new round of development after the epidemic. However, new energy vehicles , which continued to sell well during the epidemic , performed less than satisfactori...[Details]
Schematic diagram:
Different pins of the P port are selected through 2-4 decoding; 74LS139 gives +5V voltage, the output high level is above +4.5; the output low level is below 3.5V;
If SW1 is ...[Details]
Selection of power meter: Most power meters are electric. Because they need to reflect voltage and current factors, the practice voltage must be less than the withstand voltage of the voltage coil, a...[Details]
The microcontroller source program is as follows: /**************************************************************** File name: Main.c Function description: Main program *****************************...[Details]
Abstract: C504 is a single-chip microcontroller produced by the German SIEMENS company. This article introduces the application of C504 single-chip microcomputer in stepper motor control, and gi...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
