125041/W datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Topical application> Test and measurement> 125041/W

125041/W: Descriptiontest plugs & test jacks 4mm shutter plug white; CategoryTopical application Test and measurement; File Size396KB，1 Pages; ManufacturerSilvertronic; Environmental Compliance

Download Datasheet Parametric Compare View All

125041/W Overview

test plugs & test jacks 4mm shutter plug white

125041/W Parametric

Parameter Name	Attribute value
Manufacture	Silvertronic
Product Category	Test Plugs & Test Jacks
RoHS	Yes
Equipment Type	Plug
Type	Shutte
Col	White
Current Rating	20 A
Insulati	Insulated
Length	66 mm
Voltage Rating	1 kV

Preview

Download Datasheet

View All

4mm Shutter Plug

Part Number:-

Standard Colours.

Features

IEC 61010 Rating.

Measurement Category.

Current Rating.

Insultion Category.

Pollution Degree.

125041

Red Black Green Blue Yellow White

Accepts cable up to 4.5 mmØ.

1000V CAT III/600V CAT IV

20 Amp

Double/Reinforced.

Two (2)

Silvertronic confirm that the product(s) listed have been designed, manufactured and tested to

and are therefore fully compliant to:

IEC61010-031:2002 (First Edition) + Amd. 1:2008.

Together with the corresponding UL and CSA Standards, and are subject of a CB Scheme report.

All products marked as per IEC requirements. UL and CSA marking upon request.

All testing carried out by independent third party test house and CB Test Laboratory,

MET Laboratories Inc.

Baltimore MD 21230 USA

The product(s) also meet the requirements of the Low Voltage Directive and where applicable

comply with HSE GS.38.

125041/W Related Products

	125041/W	125041/Bl	125041/G	125041/Y	125041/R
Description	test plugs & test jacks 4mm shutter plug white	test plugs & test jacks 4mm shutter plug blue	test plugs & test jacks 4mm shutter plug green	test plugs & test jacks 4mm shutter plug yellow	test plugs & test jacks 4mm shutter plug red
Manufacture	Silvertronic	Silvertronic	Silvertronic	Silvertronic	-
Product Category	Test Plugs & Test Jacks	Test Plugs & Test Jacks	Test Plugs & Test Jacks	Test Plugs & Test Jacks	-
RoHS	Yes	Yes	Yes	Yes	-
Equipment Type	Plug	Plug	Plug	Plug	-
Type	Shutte	Shutte	Shutte	Shutte	-
Col	White	Blue	Gree	Yellow	-
Current Rating	20 A	20 A	20 A	20 A	-
Insulati	Insulated	Insulated	Insulated	Insulated	-
Length	66 mm	66 mm	66 mm	66 mm	-
Voltage Rating	1 kV	1 kV	1 kV	1 kV	-

Recommended Resources

Water boiling alarm circuit design

Cordless phone power control circuit

Stabilized power supply with 80% efficiency

Step wave generator circuit diagram composed of current mode op amp

CA3080 variable gain amplifier circuit

LM909 (electronic toy) radio remote control receiving and decoding circuit

[GD32L233C-START Review] Part 2 Compilation, Software Development Environment Review: [i=s]This post was last edited by yang_alex on 2022-2-17 21:50[/i]GD32L233C-START has two software development environments: Keil MDK-ARM and IAR EWARM. Keil is currently the most commonly used in Chi...; yang_alex GD32 MCU

Stuck inexplicably: //----Read data--------------------------- fly RSTA(void) {uchar e;d=0xFF;cd=1;wr=1;rd=0;_nop_();_nop_();e=d; //read datard=1;return(e); //return value } void lcdcmd0(uc cmd) //write command {uchar e=...; chenbingjy 51mcu

Realization of Chinese Characters and Graphics Overlay Based on DSP: Sharing a note from many years ago can show you how to combine digital and analog to create some innovations. Only by truly digesting and absorbing the principles and basics and applying them in pract...; Jacktang DSP and ARM Processors

Please recommend, is there any domestic dual-channel H-bridge that can drive motors with an operating voltage of 12V or above?: Intended to replace DRV8847PWPR...; sparks- Motor Drive Control（Motor Control）

How to install and use pressure transmitter: [size=4] Before installing and using the pressure transmitter, you should read the product sample and instruction manual in detail. The pressure interface should not leak during installation, and ensu...; fish001 Analogue and Mixed Signal

The flashing prompt cannot recognize the device. What's going on?: IMX6-CB200 board Why can't the device be recognized when programming with pins 66/68? The ID pin is left floating. After plugging in the USB, the DP pin level is 5V...; 明远智睿Lan Analog electronics

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components