GUB-GM8B-03-5421-C-F datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> GUB-GM8B-03-5421-C-F

GUB-GM8B-03-5421-C-F: DescriptionArray/Network Resistor, Bussed, Thin Film, 0.08W, 5420ohm, 0.25% +/-Tol, -25,25ppm/Cel, 4422,; CategoryPassive components The resistor; File Size493KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/

Download Datasheet Parametric View All

GUB-GM8B-03-5421-C-F Overview

Array/Network Resistor, Bussed, Thin Film, 0.08W, 5420ohm, 0.25% +/-Tol, -25,25ppm/Cel, 4422,

GUB-GM8B-03-5421-C-F Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Objectid	796203428
package instruction	SMT, 4422
Reach Compliance Code	compliant
Country Of Origin	USA
ECCN code	EAR99
YTEOL	6.25
structure	Molded
Network Type	Bussed
Number of terminals	16
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package height	2.286 mm
Package length	11.176 mm
Package form	SMT
Package width	5.588 mm
Rated power dissipation(P)	0.08 W
resistance	5420 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	GUB
size code	4422
technology	THIN FILM
Temperature Coefficient	25 ppm/°C
Tolerance	0.25%

Preview

Download Datasheet

View All

TaNFilm

Small Outline Surface

Mount Resistor Network

GUB Series

•

Thin ﬁlm on ceramic technology

0.220” and 0.300” sizes available

RoHS compliant version available

DESC 87012 and 87013 available

Standard JEDEC packages for automatic placement equipment

Compliant leads to

compensate for

thermal expansion

and contractions.

IRC Advanced Film Division

Ultra precision tantalum

nitride resistance element

on high purity alumina.

Rugged, molded

construction.

IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.

The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor

cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each

lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed

created by soldering and temperature excursions.

The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.

TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance

exceeding MIL-PRF-83401 characteristics H.

Electrical Data

GM Type

Resistance Range (Ω)

GL Type

Absolute Tolerance

Ratio Tolerance To R1

TCR (ppm/°C)

TCR Tracking To R1 (ppm°C)

Operating Temperature Range

Noise

Substrate

Custom circuits and special testing available.

Schem A: 10 to 200K

Schem B: 10 to 1000K

Schem A: 10 to 150K

Schem B: 10 to 75K

Available to ±0.1%

Available to ±0.05%

±25, ±50, ±100

±5

-55°C to +125°C

Less than -25 dB

High purity alumina substrate

General Note

IRC reserves the right to make changes in product speciﬁcation without notice or liability.

All information is subject to IRC’s own data and is considered accurate at time of going to print.

• 4222 South Staples Street • Corpus Christi Texas 78411 USA

Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com

A subsidiary of

TT electronics plc

GUB Series Issue November 2008 Sheet 1 of 3

Recommended Resources

Interface circuit between CMOS and ECL b

SDCS14-3-12, SDCS14-6-12 polypropylene film processing machine circuit

AD824 single supply positive and negative supply limited output low power FET input operational amplifier

Power outage emergency lighting

200W bus radio and amplifier circuit

Mamn-7 tube preamplifier circuit

Auto repair oscilloscope measuring the oxygen sensor signal of the car zirconium oxygen belt heater: Last time we talked about using an oscilloscope to measure the signal of the car's air flow meter. This time we will talk about using an oscilloscope to measure the car's oxygen sensor. The oxygen sen...; Micsig麦科信 Test/Measurement

Can the same-phase AC amplifier circuit be used for low frequencies?: [align=left][font=微软雅黑][size=12.0pt]The capacitor Ci next to R4 is equivalent to an open circuit for DC, so the DC component is not amplified; it is equivalent to a short circuit for AC, so the AC amp...; sfcsdc Analog electronics

Summary: Reading notes on "Operational Amplifier Parameter Analysis and LTspice Application Simulation": Activity details: Read the good book "Operational Amplifier Parameter Analysis and LTspice Application Simulation" for free, take notes, and thoroughly master the knowledge of operational amplifiersSu...; okhxyyo Analog electronics

How to use CPLD to collect asynchronous signals: Scenario: Use CPLD to decode a serial data channel. The data has no accompanying clock and has a fixed frequency but a different single-bit phase. My idea: I want to realize the acquisition of asynchr...; XCXBD EE_FPGA Learning Park

Share: Where should the inductor be placed on the power supply PCB?: [size=4]First, let’s ask the question: where should the coil be placed? [/size] [size=4] [/size] [size=4] Switching regulators for voltage conversion use inductors to temporarily store energy. These i...; qwqwqw2088 Analogue and Mixed Signal

[Open Source] GPIO Experiment Tutorial - Crazy Shell ARM Dual Processor Development Board Series: Table of contents Section 1LED Hardware CircuitSection 2GPIO Registers2.1 GPIO Pin Introduction2.2 Register Introduction2.2.1 P0 Data Register2.2.2 P0 Setting Data Register2.2.3 P0 reset data register...; fengke 51mcu

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components