EFM32LG880F256G-E-QFP100 datasheet, PDF

Datasheet> All Categories > The embedded processor and controller> Microcontrollers and processors> EFM32LG880F256G-E-QFP100

Preview

EFM32LG880F256G-E-QFP100: Descriptionarm microcontrollers - mcu 256k flash 32k ram 8x36 lcd aes; CategoryThe embedded processor and controller Microcontrollers and processors; File Size2MB，85 Pages; ManufacturerSilicon Laboratories Inc; Environmental Compliance

Download Datasheet Parametric Compare View All

EFM32LG880F256G-E-QFP100 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	EFM32LG880F256G-E-QFP100	-	-	View	Buy Now

EFM32LG880F256G-E-QFP100 Overview

arm microcontrollers - mcu 256k flash 32k ram 8x36 lcd aes

EFM32LG880F256G-E-QFP100 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Silicon Laboratories Inc
package instruction	LQFP-100
Reach Compliance Code	compli
ECCN code	3A001.A.3
Has ADC	YES
Address bus width	28
bit size	32
maximum clock frequency	48 MHz
DAC channel	YES
DMA channel	YES
External data bus width	16
JESD-30 code	S-PQFP-G100
length	14 mm
Number of I/O lines	85
Number of terminals	100
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
PWM channel	YES
Package body material	PLASTIC/EPOXY
encapsulated code	LFQFP
Package shape	SQUARE
Package form	FLATPACK, LOW PROFILE, FINE PITCH
ROM programmability	FLASH
Maximum seat height	1.6 mm
speed	48 MHz
Maximum supply voltage	3.8 V
Minimum supply voltage	1.98 V
Nominal supply voltage	3 V
surface mount	YES
technology	CMOS
Temperature level	INDUSTRIAL
Terminal form	GULL WING
Terminal pitch	0.5 mm
Terminal location	QUAD
width	14 mm
uPs/uCs/peripheral integrated circuit type	MICROCONTROLLER, RISC

Preview

Download Datasheet

View All

...the world's most energy friendly microcontrollers

EFM32LG880 DATASHEET

F256/F128/F64

•

ARM Cortex-M3 CPU platform

• High Performance 32-bit processor @ up to 48 MHz

• Memory Protection Unit

•

Flexible Energy Management System

• 20 nA @ 3 V Shutoff Mode

• 0.4 µA @ 3 V Shutoff Mode with RTC

• 0.65 µA @ 3 V Stop Mode, including Power-on Reset, Brown-out

Detector, RAM and CPU retention

• 0.95 µA @ 3 V Deep Sleep Mode, including RTC with 32.768 kHz

oscillator, Power-on Reset, Brown-out Detector, RAM and CPU

retention

• 63 µA/MHz @ 3 V Sleep Mode

• 211 µA/MHz @ 3 V Run Mode, with code executed from flash

•

256/128/64 KB Flash

•

32 KB RAM

•

85 General Purpose I/O pins

• Configurable push-pull, open-drain, pull-up/down, input filter, drive

strength

• Configurable peripheral I/O locations

• 16 asynchronous external interrupts

• Output state retention and wake-up from Shutoff Mode

•

12 Channel DMA Controller

•

12 Channel Peripheral Reflex System (PRS) for autonomous in-

ter-peripheral signaling

•

Hardware AES with 128/256-bit keys in 54/75 cycles

•

Timers/Counters

• 4× 16-bit Timer/Counter

• 4×3 Compare/Capture/PWM channels

• Dead-Time Insertion on TIMER0

• 16-bit Low Energy Timer

• 1× 24-bit Real-Time Counter and 1× 32-bit Real-Time Counter

• 3× 16/8-bit Pulse Counter

• Watchdog Timer with dedicated RC oscillator @ 50 nA

•

Integrated LCD Controller for up to 8×36 segments

• Voltage boost, adjustable contrast and autonomous animation

•

Backup Power Domain

• RTC and retention registers in a separate power domain, avail-

able in all energy modes

• Operation from backup battery when main power drains out

•

External Bus Interface for up to 4×256 MB of external

memory mapped space

• TFT Controller with Direct Drive

•

Communication interfaces

• 3× Universal Synchronous/Asynchronous Receiv-

er/Transmitter

• UART/SPI/SmartCard (ISO 7816)/IrDA/I2S

• 2× Universal Asynchronous Receiver/Transmitter

• 2× Low Energy UART

• Autonomous operation with DMA in Deep Sleep

Mode

• 2× I C Interface with SMBus support

• Address recognition in Stop Mode

•

Ultra low power precision analog peripherals

• 12-bit 1 Msamples/s Analog to Digital Converter

• 8 single ended channels/4 differential channels

• On-chip temperature sensor

• 12-bit 500 ksamples/s Digital to Analog Converter

• 2× Analog Comparator

• Capacitive sensing with up to 16 inputs

• 3× Operational Amplifier

• 6.1 MHz GBW, Rail-to-rail, Programmable Gain

• Supply Voltage Comparator

•

Low Energy Sensor Interface (LESENSE)

• Autonomous sensor monitoring in Deep Sleep Mode

• Wide range of sensors supported, including LC sen-

sors and capacitive buttons

•

Ultra efficient Power-on Reset and Brown-Out Detec-

tor

•

Debug Interface

• 2-pin Serial Wire Debug interface

• 1-pin Serial Wire Viewer

• Embedded Trace Module v3.5 (ETM)

•

Pre-Programmed UART Bootloader

•

Temperature range -40 to 85 ºC

•

Single power supply 1.98 to 3.8 V

•

LQFP100 package

32-bit ARM Cortex-M0+, Cortex-M3 and Cortex-M4 microcontrollers for:

• Energy, gas, water and smart metering

• Health and fitness applications

• Smart accessories

• Alarm and security systems

• Industrial and home automation

...the world's most energy friendly microcontrollers

into two blocks; the main block and the information block. Program code is normally written to the main

block. Additionally, the information block is available for special user data and flash lock bits. There is

also a read-only page in the information block containing system and device calibration data. Read and

write operations are supported in the energy modes EM0 and EM1.

2.1.4 Direct Memory Access Controller (DMA)

The Direct Memory Access (DMA) controller performs memory operations independently of the CPU.

This has the benefit of reducing the energy consumption and the workload of the CPU, and enables

the system to stay in low energy modes when moving for instance data from the USART to RAM or

from the External Bus Interface to a PWM-generating timer. The DMA controller uses the PL230 µDMA

controller licensed from ARM.

2.1.5 Reset Management Unit (RMU)

The RMU is responsible for handling the reset functionality of the EFM32LG.

2.1.6 Energy Management Unit (EMU)

The Energy Management Unit (EMU) manage all the low energy modes (EM) in EFM32LG microcon-

trollers. Each energy mode manages if the CPU and the various peripherals are available. The EMU

can also be used to turn off the power to unused SRAM blocks.

2.1.7 Clock Management Unit (CMU)

The Clock Management Unit (CMU) is responsible for controlling the oscillators and clocks on-board

the EFM32LG. The CMU provides the capability to turn on and off the clock on an individual basis to all

peripheral modules in addition to enable/disable and configure the available oscillators. The high degree

of flexibility enables software to minimize energy consumption in any specific application by not wasting

power on peripherals and oscillators that are inactive.

2.1.8 Watchdog (WDOG)

The purpose of the watchdog timer is to generate a reset in case of a system failure, to increase appli-

cation reliability. The failure may e.g. be caused by an external event, such as an ESD pulse, or by a

software failure.

2.1.9 Peripheral Reflex System (PRS)

The Peripheral Reflex System (PRS) system is a network which lets the different peripheral module

communicate directly with each other without involving the CPU. Peripheral modules which send out

Reflex signals are called producers. The PRS routes these reflex signals to consumer peripherals which

apply actions depending on the data received. The format for the Reflex signals is not given, but edge

triggers and other functionality can be applied by the PRS.

2.1.10 External Bus Interface (EBI)

The External Bus Interface provides access to external parallel interface devices such as SRAM, FLASH,

ADCs and LCDs. The interface is memory mapped into the address bus of the Cortex-M3. This enables

seamless access from software without manually manipulating the IO settings each time a read or write

is performed. The data and address lines are multiplexed in order to reduce the number of pins required

to interface the external devices. The timing is adjustable to meet specifications of the external devices.

The interface is limited to asynchronous devices.

2.1.11 TFT Direct Drive

The EBI contains a TFT controller which can drive a TFT via a 565 RGB interface. The TFT controller

supports programmable display and port sizes and offers accurate control of frequency and setup and

hold timing. Direct Drive is supported for TFT displays which do not have their own frame buffer. In

2014-06-13 - EFM32LG880FXX - d0117_Rev1.30

www.silabs.com

...the world's most energy friendly microcontrollers

that case TFT Direct Drive can transfer data from either on-chip memory or from an external memory

device to the TFT at low CPU load. Automatic alpha-blending and masking is also supported for transfers

through the EBI interface.

2.1.12 Inter-Integrated Circuit Interface (I2C)

The I C module provides an interface between the MCU and a serial I C-bus. It is capable of acting as

both a master and a slave, and supports multi-master buses. Both standard-mode, fast-mode and fast-

mode plus speeds are supported, allowing transmission rates all the way from 10 kbit/s up to 1 Mbit/s.

Slave arbitration and timeouts are also provided to allow implementation of an SMBus compliant system.

The interface provided to software by the I C module, allows both fine-grained control of the transmission

process and close to automatic transfers. Automatic recognition of slave addresses is provided in all

energy modes.

2.1.13 Universal Synchronous/Asynchronous Receiver/Transmitter (US-

ART)

The Universal Synchronous Asynchronous serial Receiver and Transmitter (USART) is a very flexible

serial I/O module. It supports full duplex asynchronous UART communication as well as RS-485, SPI,

MicroWire and 3-wire. It can also interface with ISO7816 SmartCards, IrDA and I2S devices.

2.1.14 Pre-Programmed UART Bootloader

The bootloader presented in application note AN0003 is pre-programmed in the device at factory. Auto-

baud and destructive write are supported. The autobaud feature, interface and commands are described

further in the application note.

2.1.15 Universal Asynchronous Receiver/Transmitter (UART)

The Universal Asynchronous serial Receiver and Transmitter (UART) is a very flexible serial I/O module.

It supports full- and half-duplex asynchronous UART communication.

2.1.16 Low Energy Universal Asynchronous Receiver/Transmitter

(LEUART)

The unique LEUART , the Low Energy UART, is a UART that allows two-way UART communication on

a strict power budget. Only a 32.768 kHz clock is needed to allow UART communication up to 9600 baud/

s. The LEUART includes all necessary hardware support to make asynchronous serial communication

possible with minimum of software intervention and energy consumption.

2.1.17 Timer/Counter (TIMER)

The 16-bit general purpose Timer has 3 compare/capture channels for input capture and compare/Pulse-

Width Modulation (PWM) output. TIMER0 also includes a Dead-Time Insertion module suitable for motor

control applications.

2.1.18 Real Time Counter (RTC)

The Real Time Counter (RTC) contains a 24-bit counter and is clocked either by a 32.768 kHz crystal

oscillator, or a 32.768 kHz RC oscillator. In addition to energy modes EM0 and EM1, the RTC is also

available in EM2. This makes it ideal for keeping track of time since the RTC is enabled in EM2 where

most of the device is powered down.

2.1.19 Backup Real Time Counter (BURTC)

The Backup Real Time Counter (BURTC) contains a 32-bit counter and is clocked either by a 32.768 kHz

crystal oscillator, a 32.768 kHz RC oscillator or a 1 kHz ULFRCO. The BURTC is available in all Energy

Modes and it can also run in backup mode, making it operational even if the main power should drain out.

2014-06-13 - EFM32LG880FXX - d0117_Rev1.30

www.silabs.com

EFM32LG880F256G-E-QFP100 Related Products

	EFM32LG880F256G-E-QFP100	EFM32LG880F64G-E-QFP100	EFM32LG880F128G-E-QFP100	EFM32LG880F128G-E-QFP100R
Description	arm microcontrollers - mcu 256k flash 32k ram 8x36 lcd aes	arm microcontrollers - mcu 64k flash 32k ram 8x36 lcd aes	arm microcontrollers - mcu 128k flash 32k ram 8x36 lcd aes	arm microcontrollers - mcu 128k flash 32k ram 8x36 lcd aes
Manufacture	-	Silicon Laboratories	Silicon Laboratories	Silicon Laboratories
Product Category	-	ARM Microcontrollers - MCU	ARM Microcontrollers - MCU	ARM Microcontrollers - MCU
RoHS	-	Yes	Yes	Yes
Core	-	ARM Cortex M3	ARM Cortex M3	ARM Cortex M3
Data Bus Width	-	32 bi	32 bi	32 bi
Maximum Clock Frequency	-	48 MHz	48 MHz	48 MHz
Program Memory Size	-	64 kB	64 kB	64 kB
Data RAM Size	-	32 kB	32 kB	32 kB
On-Chip ADC	-	Yes	Yes	Yes
Operating Supply Voltage	-	2 V to 3.8 V	2 V to 3.8 V	2 V to 3.8 V
Maximum Operating Temperature	-	+ 85 C	+ 85 C	+ 85 C
Package / Case	-	LQFP-100	LQFP-100	LQFP-100
Mounting Style	-	SMD/SMT	SMD/SMT	SMD/SMT
A/D Bit Size	-	12 bi	12 bi	12 bi
Data RAM Type	-	RAM	RAM	RAM
Data ROM Size	-	64 kB	128 kB	128 kB
Data ROM Type	-	Flash	Flash	Flash
Interface Type	-	I2C, SPI, UART, USB	I2C, SPI, UART, USB	I2C, SPI, UART, USB
Minimum Operating Temperature	-	- 40 C	- 40 C	- 40 C
Number of Programmable I/Os	-	85	85	85
Number of Timers	-	5	5	5
On-Chip DAC	-	Yes	Yes	Yes
Packaging	-	Tray	Tray	Reel
Processor Series	-	EFM32	EFM32	EFM32
Program Memory Type	-	Flash	Flash	Flash

Recommended Resources

One of the Y-△ simple buck voltage circuits with anti-arc flashover short circuit protection function

Power supply circuit diagram composed of M5237L

Variable gain constant voltage output circuit

Welding machine no-load self-stop power saving control circuit

Half-duplex circuit current loop multi-machine communication interface circuit

electronic thermometer

Can DMA1 and DMA2 of stm32f4 transfer data simultaneously?: When performing DMA transmission of the serial port, can DMA1 and DMA2 of stm32f4 transmit data at the same time? For example, if the data stream and channel corresponding to usart1 in DMA2 are turned...; shijizai stm32/stm8

WIFI(RTL8188EUS) Guide: [b]MY-IMX6 Development Guide WIFI (RTL8188EUS)[/b][color=rgb(37, 37, 37)][font=sans-serif][size=0.875em] [size=13.3px][align=center][b]Directory[/b][size=12.502px] [[color=rgb(11, 0, 128)][url=http://...; 明远智睿Lan ARM Technology

How to use multiple devices to study radiation signals - Part 2: This content is originally created by EEWORLD forum user zhouyunying . If you want to reprint or use it for commercial purposes, you must obtain the author's consent and indicate the source Last time,...; zhouyunying Talking

TPS54331 DCDC ripple interferes with radio: [size=4]The TPS54331 device is a 28-V, 3-A nonsynchronous step-down converter with an integrated low RDS(on) high-side MOSFET. To improve efficiency at light loads, the pulse-skipping Eco-mode functio...; Jacktang Analogue and Mixed Signal

TI eSMO library Fsmopos and Gsmopos parameter analysis: Author: Hardy Zhou In terms of motor sensorless control algorithm, TI provides eSMO sliding mode observer to calculate the motor rotor angle. In terms of application, TI provides eSMO lib file and rel...; alan000345 DSP and ARM Processors

Variable initialization problem in single chip microcomputer programming: In MCU programming, I have made many mistakes in variable initialization. The most common mistake is that when defining a variable, especially a local variable inside a function, the variable is not i...; 火辣西米秀 Microcontroller MCU

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components