Y002427R1000A9L datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> Y002427R1000A9L

Y002427R1000A9L: DescriptionFixed Resistor, Metal Foil, 0.3W, 27.1ohm, 300V, 0.05% +/-Tol, -2,2ppm/Cel, 4216,; CategoryPassive components The resistor; File Size451KB，6 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

Y002427R1000A9L Overview

Fixed Resistor, Metal Foil, 0.3W, 27.1ohm, 300V, 0.05% +/-Tol, -2,2ppm/Cel, 4216,

Y002427R1000A9L Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	851312463
Reach Compliance Code	compliant
Country Of Origin	Israel
ECCN code	EAR99
YTEOL	10
structure	Hermetically Sealed
Lead diameter	0.64 mm
Lead length	25.4 mm
lead spacing	3.81 mm
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package height	10.92 mm
Package length	10.54 mm
Package form	Radial
Package width	4.11 mm
method of packing	Bulk
Rated power dissipation(P)	0.3 W
resistance	27.1 Ω
Resistor type	FIXED RESISTOR
series	H(OTHER)
size code	4216
technology	METAL FOIL
Temperature Coefficient	2 ppm/°C
Tolerance	0.05%
Operating Voltage	300 V

Preview

Download Datasheet

View All

H Series

Vishay Foil Resistors

New Generation of Secondary Standards Hermetically Sealed High Precision Bulk

Metal

Foil Technology Resistors with TCR of ± 2 ppm/°C, Tolerance of ± 0.001 % and

Load Life Stability of ± 0.005 % (Metrology, Laboratory, Instrumentation, Industrial)

FEATURES

•

Temperature coefficient of resistance (TCR):

± 2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C

ref.).

For

ultra

high

performances

(instrumentation and metrology) please refer to

the last page

•

Resistance range: 5

to 1.84 MΩ (higher or

lower values of resistance available)

•

Vishay Foil resistors are not restricted to standard values;

specific “as required” values can be supplied at no extra

cost or delivery (e.g. 1K2345 vs. 1K)

•

Power rating: 0.3 W to 2.5 W at + 25 °C (depending on

model - see table 2)

•

Tolerance: to ± 0.001 % (10 ppm)

•

Load life stability to ± 0.002 % (20 ppm) at 25 °C, 2000 h

at rated power

•

Load life stability can be considerably improved

through in-house stabilization

•

Shelf life stability: ± 2 ppm for at least 6 years

(unaffected by humidity)

•

Electrostatic discharge (ESD) up to 25 000 V

•

Rise time: 1 ns effectively no ringing

•

Thermal stabilization time < 1 s (nominal value achieved

within 10 ppm of steady state value)

•

Current noise: 0.010 µV

RMS

/V of applied voltage (< - 40 dB)

•

Thermal EMF: 0.05 µV/°C typical

•

Voltage coefficient: < 0.1 ppm/V

•

Non-inductive: < 0.08 µH

•

Non-inductive, non-capacitive design

•

Non hot spot design

•

Terminal finish available: lead (Pb)-free or tin/lead alloy

•

Impervious to harmful environments - oil-filled

•

Compliant to RoHS directive 2002/95/EC

•

Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vishaypg.com

•

For better performances (values, TCR, tolerance, stability),

please see the HZ series

INTRODUCTION

The H series resistors are oil-filled, hermetically sealed ultra

precision resistors and are used as secondary standards for

metrology applications.

The hermetic sealing eliminates the ingress of moisture and

oxygen, while the oil acts as a thermal conductor, thus

eliminating the long-term degradation elements of unsealed

resistors, while at the same time allowing the device to

accept short periods of overload without degradation.

Vishay’s Bulk Metal

Foil outperforms all other resistor

technologies available today for applications that require

precision and stability. When combined with the hermetic

sealing and oil filling, the H series resistors become

the most

precise and stable resistors available.

With accuracies of 0.001 %, a resistance range from 5

to 1.84 MΩ, and long term shelf life of less than 2 ppm,

these devices are virtually secondary standards that can be

carried in sets for daily or periodic calibration of factory

measurement equipment.

The H series is available with laboratory and metrology

level precision and long-term stability with additional

in-house oriented processes such as: chip stabilization,

special TCR plotting, additional treatments for ultra

stability and special post manufacturing operations

(PMO). (Please refer to the last page)

TABLE 1 - TCR VS. RESISTANCE VALUE

RESISTANCE

VALUE (Ω)

100 to < 1M84

50 to < 100

5 to < 50

TYPICAL TCR AND MAX. SPREAD

(- 55 °C to + 125 °C, + 25 °C ref.)

(ppm/°C)

± 2 ± 2.5

± 2 ± 3.5

± 2 ± 4.5

FIGURE 1 - SHELF LIFE - VHA518-11

12K9 VS. QHE

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

- 0.1

100 200 300 400 500 600 700 800 900 1000

Note

• For maximum TCR < 1 ppm/°C, see VHP100 and contact

application engineering

* Pb containing terminations are not RoHS compliant, exemptions may apply

Resistance Change (ppm)

Time (Days)

Document Number: 63006

Revision: 23-Mar-10

For any questions, contact:

foil@vishaypg.com

www.foilresistors.com

Recommended Resources

IR2130 application wiring diagram in three-phase fixed frequency output power supply system

Modem circuit consisting of XR-210 and XR-2207

Rectifier circuit diagram of LED assembly

Water level automatic control circuit

Gas Smoke Alarm 4

555 multi-function electronic controller circuit

It's time to test your eyesight: It's been a while since I posted a question that tests your eyesight. I'll post one today....; okhxyyo Talking

12V lithium battery, is there any suitable charging circuit recommended?: I recently had a project that used a 12V lithium battery. I would like to ask if you have a stable 12V lithium battery charging circuit solution? Thank you very much~ The lithium battery is 3 series a...; wangerxian Power technology

I2C operation of RSL10 and reading of acceleration measurement data of KX023: [i=s]This post was last edited by cruelfox on 2021-7-2 20:48[/i]　　The I2C interface access of RSL10 can be realized by using the API provided by SDK, of course, you can also operate the registers your...; cruelfox onsemi and Avnet IoT Innovation Design Competition

The input voltage of the boost circuit is 9 to 16V. The output voltage range is 31V to 50V. How do I calculate the inductance?: The input voltage of the boost circuit is 9 to 16V. The output voltage range is 31V to 50V. How should I calculate the inductance? Under what conditions should I calculate? When the input is 9V and th...; 小太阳yy Switching Power Supply Study Group

Register and download to win practical gifts! Have you used ECal? Do you know Rcal?: Speaking of test calibration, The first thing that comes to mind for the "Siege Lions" is Calibration of network analyzers.When you use a network analyzer for testing, Calibration is a mandatory actio...; eric_wang Test/Measurement

QUARTUS 9.0 simulation output is always low level: is a cascade counter. The output is always low level...; yyy7797879 FPGA/CPLD

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components