EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

P1505E2612WN

Description
RESISTOR, THIN FILM, 0.35 W, 0.05 %, 25 ppm, 26100 ohm, SURFACE MOUNT, 1505, CHIP, GREEN
CategoryPassive components    The resistor   
File Size121KB,9 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet Parametric View All

P1505E2612WN Overview

RESISTOR, THIN FILM, 0.35 W, 0.05 %, 25 ppm, 26100 ohm, SURFACE MOUNT, 1505, CHIP, GREEN

P1505E2612WN Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1747881767
package instructionSMT, 1505
Reach Compliance Codecompliant
Country Of OriginFrance
ECCN codeEAR99
YTEOL8.45
Other featuresHIGH PRECISION, STANDARD: MIL-PRF-55342G
structureChip
JESD-609 codee2
Manufacturer's serial numberP
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.5 mm
Package length3.81 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width1.32 mm
method of packingWAFFLE PACK
Rated power dissipation(P)0.35 W
Rated temperature70 °C
GuidelineMIL-PRF-55342G
resistance26100 Ω
Resistor typeFIXED RESISTOR
seriesP1505
size code1505
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Silver (Sn/Ag) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.05%
Operating Voltage75 V
Verilog basic question
Can the initial statement implement loops or nested operations?...
Gerryi EE_FPGA Learning Park
Smart Lock
describe Design an electronic smart lock with integrated Wi-Fi using the Battery Powered Smart Lock reference design, LaunchPad kit, and motor drive evaluation module. Reference DesignBattery-Powered ...
Jacktang Wireless Connectivity
I need help designing a 100mA constant current source. I already have a circuit and need analysis.
[i=s]This post was last edited by 244141084 on 2020-10-9 11:43[/i]The power supplies in the picture are all 5V. I can understand the first two op amps, but I can't understand the op amp with a MOS tub...
244141084 Analog electronics
Why does the output voltage of an op amp need to be offset? Analysis of the principle of differential circuit
The differential operational amplifier circuit effectively suppresses the common-mode signal and only amplifies the differential signal, so it is widely used.Circuit Configuration of Differential Circ...
infinigo Integrated technical exchanges
[Mill MYC-J1028X development board trial] Use Node-RED to transform the MYC-J1028X development board into an industrial control gateway
[i=s]This post was last edited by HonestQiao on 2022-10-2 10:59[/i]This article is long and involves many knowledge points. You need to read it patiently. The following is the directory of specific co...
HonestQiao NXP MCU
How to calculate power saving based on power factor?
I would like to ask you, the 250W high pressure sodium lamp street light used to have no compensation (power factor was 0.5), the stable current was 3.8A, now after compensation the power factor becom...
nhsl Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号