Motionnet
MNET-J3/S23/MIA/DA2/SAN
Distributed Single-axis Motion Control Modules
(please refer to page 6-30)
Introduction
ADLINK’s Motionnet products provide system integrators with a simple configuration and reduced wiring method for a cost-effective solution for motion
applications utilizing multiple single axis. With this new concept of direct plug-in modules, the amount of space used and the amount of wiring required is greatly
reduced from traditional terminal board connections.
After the module is plugged into the servo driver, all that is needed is a LAN cable to make the serial connection between the modules. Different servo drivers can
be lined up on the Motionnet bus, making motion control configuration much simpler than PCI board solutions. The Motionnet bus can support up to 64 single-
axis modules.
Features
■
■
Specifications
■
■
■
■
■
■
■
■
■
■
■
■
No command frequency limitation
Available for Mitsubishi J3A/J4A, Panasonic MINAS A4/A5,
and Yaskawa Sigma V, Delta A2, and Sanyo R series
Up to 64 axes, serially connected
No need for terminal boards – reduces space
The scanning cycle time up to 0.97 ms at 20 Mbps when
64 axes are connected
Point-to-point application can be easily completed with
multiple single-axis modules
Supports linear/s-curve acceleration and deceleration
Power Indicator
Operating Temperature
Operating Ambient Humidity
Environmental
Vibration
Weight
Dimensions
Displays the status of the 3.3 V
DC
internal control power (red LED)
0˚C to +50˚C (32˚F to 122˚F)
80% RH or less (non-condensing within the 10˚C to 50°C range)
RoHS compliant
JIS C0040 compliant
Approximately 50 g
52.4 x 16.3 x 69.5 mm (W x H x D) (2.04” x 0.63” x 2.71”)
Ordering Information
■
MNET-J3
Motionnet distributed single-axis motion control module for
Mitsubishi J3A/J4A
■
MNET-S23
Motionnet distributed single-axis motion control module for
Yaskawa Sigma V
■
MNET-MIA
Motionnet distributed single-axis motion control module for
Panasonic MINAS A4/A5
■
MNET-DA2
Motionnet distributed single-axis motion control module for
Delta A2
■
MNET-SAN
Motionnet distributed single-axis motion control module for
Sanyo R series
No
1
2
3
9
CN3
9
CN3
Pin Assignment
1
1
1
3
1
1
3
CN2
3
CN2
1
3
CN1
CN1
EHG ORG SD MEL PEL
10
EHG ORG SD MEL PEL
10
Name
Name
ERR RUN POWER
2
ERR RUN POWER
2
No
1
2
3
RS485+
RS485+
RS485-
RS485-
FG
FG
Name
Serial
communicationdata+
Serial
communicationdata+
Communication data+
Communication data+
Frame
Frame
ground
ground
Function
CN3 Pin Assignment
CN1/CN2 Pin Assignment
CN1/CN2 Pin Assignment
Function
Signal
Function
Signal Direction
Direction
I/O
I/O
-
I/O
I/O
-
CN3
CN3
CN2
CN1
No
No
1
2
3
4
5
6
7
8
9
10
1
PEL
Name
2
MEL
PEL
3
SD/CPP
4
MEL
ORG
5
SD/CPP
EMGI
6
ORG
CPN
7
24V
EMGI
8
GND
9
CPN
GND
10
24V
FG
GND
GND
FG
Positive end limit
Slowdown input / comparator output (+)
Negative end limit
Zero position input
Emergency stop
/ comparator output (+)
Slowdown input
input
Comparator output (-)
Zero position input
24 V
DC
Power source
Emergency stop input
Ground
Comparator output (-)
Ground
Frame
Power
24 V
DC
ground
source
Ground
Ground
Frame ground
CN3 Pin Assignment
Signal Direction
Positive end
I
Function
limit
Signal Direction
Negative end limit
I
I/O
I
I
O
I
I
I
-
I
I
I/O
I
I
O
I
I
I
-
EHG ORG SD MEL PEL
ERR RUN POWER
EHG ORG SD MEL PEL
Powe
(3.3V
Communi
LED
Communicatio
LED
Mechanical input status indicato
(PEL,MEL,SD,ORG,EMG)
(PEL,MEL,S
Updated January 29, 2013.
©2013
ADLINK Technology, Inc. All Rights Reserved. All specifications are subject to change without further notice.
Mechanical