The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts absorb on the top
tapes to cause a failure in the mounting and the parts are destructed by static electricity (more than 1kV : 1J, 2A, 2B, 2E 0.5kV : 1E, Human Body Model 100pF 1.5kΩ) to change the
resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged on the tapes. Similarly, care should be given not to apply the
excessive static electricity when mounting on the boards.
●
Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc. The flux may
contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na
＋
), chrorine (Cl
−
) etc. Therefore these kinds of ionic substances may
induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since lead free solder contains ionic substances.
Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
●
Please pay attention that the top of an iron does not direct touch to the components. There is a risk that may cause a change in resistance. Take care that another risk may happen that
the protecting coat is carbonized in an instant when touched directly by the top of the iron, also climatic-proof for electric corrosion or insulation of protecting coat may be dropped down.
Be sure not to give high temperature on the top of the iron as it will degrade the protecting coat.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling strength. 5∼
35℃/35∼75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas like hydrogen sulfide, sulfurous acid
gas, hydrogen chloride, etc. may drop solderability.
If you want to become a qualified hardware engineer, it is very important to master the knowledge of power supply.All working systems must have power supply, and whether the power supply is reliable a...
1. Serial port programming general block diagramMini2440 serial port communication (UART0)二、分步介绍
#define GPHCON(*(volatile unsigned long *)0x56000070)
#define ULCON0(*(volatile unsigned long *)0x50000...
I hope that the STM32 NUCLEO development board will launch a version with integrated USB HS PHY in the future.
The current problem is that the I/O resources of the DK board are insufficient, and the c...
People are now paying attention to "flat-screen TVs" and "
solar batteries
". Both fields focus on environmental protection and require the development of low-loss, high-efficiency products.
...[Details]
In recent years, due to the rapid development of integrated circuits, reference voltage sources have been widely used in analog integrated circuits, mixed analog and digital circuits, and system inte...[Details]
1 Introduction
With the development of industrial automation technology, PLC/DCS systems play an increasingly important role in the automation of industrial control, the safety and reliability ...[Details]
According to foreign media reports, Marelli, a leading global automotive supplier, has launched the first power module that can be used for electric and hybrid traction control in racing cars. This n...[Details]
While imaging industry experts know that Apple has designed a complex 3D camera for its iPhone X, called "TrueDepth," most of the details of the 3D system inside the module, including chips, componen...[Details]
In the past decade, in the field of vehicle
electronic and electrical architecture
development,
model-
based development methods have been widely accepted and even used as the prefer...[Details]
On December 26, 2019, the Shanghai 110 kV Xuzhen substation multi-station integration project was officially put into operation, marking that the State Grid Shanghai Electric Power Company has full...[Details]
0 Introduction At present, the microcontroller course set up by various colleges and universities in response to development is an important course for electrical majors such as mechatronics and...[Details]
The calibrated on-chip RC oscillator provides a fixed 1.0, 2.0, 4.0, or 8.0 MHz clock. These frequencies are nominal values at 5V, 25°C. This clock can also be used as the system clock by programmi...[Details]
On January 22, Apple concept stocks suffered a setback as a whole, with many stocks falling. The Apple concept sector fell as much as 1.39%, among which Lens Technology fell more than 13% during the ...[Details]
Indian tech blog MySmartPrice has obtained 3D renders of what it says are standard iPhone 13 models, showing a familiar design but with some notable changes, including a smaller notch and a new diago...[Details]
According to the latest research report released by Strategy Analytics, the total revenue of the global smartphone image sensor market in 2020 was US$15 billion, with overall revenue increasing by 13...[Details]
A three-coordinate measuring machine is an optical instrument that can measure geometric shapes, lengths, roundness, and circumference divisions within a hexahedral space . There are many types of th...[Details]
CAN bus (Controller Area Network) is a local area network based on broadcast technology, which is widely used in automobiles, industrial automation, medical equipment and other fields. However, in ...[Details]
EE_FPGA Learning Park
京公网安备 11010802033920号
EEWORLD
