The VC-707 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes
on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme
as shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
OUT+
OUT-
100
LVDS
Receiver
LVDS
Driver
100
Receiver
Figure 11 LVDS to LVDS Connection, Internal 100ohm
Some LVDS structures have an internal 100 ohm resistor
on the input and do not need additional components.
Figure 10 Standard LVDS
Output Configuration
Figure 12 LVDS to LVDS Connection
External 100ohm and AC blocking caps
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if it one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
[i=s]This post was last edited by Jacktang on 2019-4-19 08:30[/i] TIDEP-0091 highlights the IWR14xx 76- to 81-GHz mmWave sensor power optimization strategy for tank level detection applications, displ...
At the tail end of 2019, the long-awaited "Double 12" is here again. In order to thank fans for their attention throughout the year, STMicroelectronics Power and Discrete Devices (PDSA) sincerely invi...
eric_wangST Sensors & Low Power Wireless Technology Forum
Bell(B)
Bell (B) was originally used to represent the ratio of volume power 10 to 1, named after Alexander Graham Bell. 1B represents a power ratio of 10:1, so this is a logarithmic relationship with ...
In order to try out the Eagle software from Autocad, I opened the software after installation and found this!!!
Brother, I have no ill intentions. I was just trying out the software. Why are you treat...
[size=4] [/size] [size=4][color=#ff0000][b]Heroes from all walks of life, EEWORLD is sending out hero invitations to everyone, and offering cash rewards of equal value to recruit the following good ar...
Hello~ Everyone~ The new week's review information is here~~ Tomorrow is National Day~ I wish you all a happy holiday! Let's get back to the topic, let's take a look at the latest review information~A...
The automotive industry is one of the key sectors driving the development of artificial intelligence (AI) as it focuses on the ubiquitous benefits of autonomous vehicles and advanced driver assista...[Details]
Li Rushi, our reporter In the field of solid-state batteries, the strongest feeling this year is that more and more entrants have emerged, and the research and development competition in the correspon...[Details]
introduction DC regulated power supply is a relatively common electronic device, which has been widely used in many fields such as electronic circuits, experimental teaching, scientific research...[Details]
According to Wuxi Daily, after signing the contract this year, Wuxi Lanpei New Materials Technology Co., Ltd. completed the renovation of the Huishan clean workshop and the relocation of its Shanghai...[Details]
JTAG (Joint Test Action Group) is an international standard test protocol (IEEE 1149.1 compatible), which is currently mainly used for internal chip testing. Most advanced devices now support the JTAG...[Details]
Vishay Introduces 7575-Size IHLP® Commercial Inductors for Continuous Operation to +155°C
The inductor is available in a 19 mm x 19 mm x 7 mm package, offering low DCR compared to 67...[Details]
On March 14, NIO held a long-life battery strategic communication meeting. At the meeting, NIO proposed a long-life battery solution. The goal is to use the healthy operation of the full life cycle o...[Details]
On August 11, 2017, WPG Holdings, a leading semiconductor component distributor dedicated to the Asia-Pacific market, announced that its subsidiary Pinjia is promoting a new automotive LED headlight ...[Details]
By using a simple and straightforward transmission line model, it is possible to accurately model and analyze microstrip inset-fed patch antennas.
Small, low-cost antennas are used in many mod...[Details]
External reset is generated by a low level applied to the RESET pin. When the reset low level duration is greater than the minimum pulse width (see Table 19), the reset process is triggered, even if ...[Details]
According to DigiTimes, Apple is increasing the production of mini-LED chips and incorporating more manufacturers into its supply chain to meet demand for new devices in 2022. Apple has expanded it...[Details]
With breakthroughs in AI technology and the innovative application of large language models in smart driving and smart cockpits, intelligence has become a development trend in the automotive indust...[Details]
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
Use the 8X8 dot matrix to display the numbers 0 to 9 one by one, and then restart from 0 after 9, and repeat this cycle. Solution 1: Use interrupts to set all row values to low level at all times...[Details]
1. Overview of Thermal Management System for New Energy Vehicles
Automotive thermal management refers to the overall control of vehicle heat and ambient heat from the perspective of the system...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
