Microwave Five Lectures : https://training.eeworld.com.cn/course/5780What is microwave, how was it discovered, how do people use electromagnetic waves, how to design microwave circuits and antennas, t...
In the post [url=https://en.eeworld.com/bbs/thread-1067616-1-1.html]Hello Buttons[/url], we used SW1 - SW4 buttons to change the display color of the RGB LED. The User Buttons Element inside was used ...
As shown in Figure 1, this is a USB mounting hole. I want to make this mounting hole into a plum blossom solder pad, but it does not need to be grounded. I want to make it into an independent exposed ...
This is an introductory guide on how to get started with a project involving I2C communication using the ultra-low-power MSP microcontrollers (MCUs):
Introduction
I2C (or I2C, Integrated Circuit Bus) ...
[i=s]This post was last edited by damiaa on 2018-9-15 09:39[/i] 【GD32-colibri-F350RX】+LED or button or UART print test 1. Download GD32F3x0_Firmware_Library_V1.0.0 from the GD official website and unz...
1 Introduction to SHT11
SHT11 is a digital temperature and humidity sensor
chip
launched by Swiss company Scnsirion
. This chip is widely used in HVAC, automobile, consumer electro...[Details]
CAN consistency testing aims to reduce the differences between CAN bus nodes and improve the anti-interference ability of the bus, thereby ensuring the stability of the device CAN network system. Th...[Details]
On August 4, 2022, WPG Holdings, a leading semiconductor component distributor dedicated to the Asia-Pacific market, announced that its subsidiary Pinjia launched
an automotive electric tailgate s...[Details]
Motor setting techniques are two core aspects in the field of motor control and are explained below.
Motor setting skills:
Motor setting skills refer to the parameter setting and deb...[Details]
In the previous section, we introduced the driver of STM8 microcontroller GPIO based on the standard library. This section mainly introduces the driver of STM8 timer. Let's first open the specifica...[Details]
A typical electric vehicle (EV) charging station design for commercial and residential use includes energy metering, residual current detection (AC and DC), isolation safety compliance, relays and ...[Details]
; STEP_3.ASM (12C508 / 12C509) ;
; Controls a stepping motor driver on GPIO bits 4, 2, 1 and 0.
;
; The direction is controlled by a switch on GPIO bit 3. Bit 5 is not
used.
;
; (Typical d...[Details]
With the continuous development of the economy and society, people's living standards have been gradually improved, and the requirements for the environment have become higher and higher. The exhau...[Details]
"The next generation of robots will 'coexist with humans'. If China can seize this opportunity, it will play a special role in the robot innovation arena. If it loses this opportunity, it may fall ...[Details]
Sina Digital News reported on the afternoon of September 3 that Qualcomm launched a number of chips during the IFA Berlin International Consumer Electronics Show, covering a variety of termina...[Details]
The 2011 Guangzhou International Lighting Exhibition was held recently. Many manufacturers at the exhibition complained to Southern Metropolis Daily reporters that although LED has developed rapidl...[Details]
Active and differential probes
The increasing number of signals and decreasing voltages of logic families make it difficult for designers to achieve accurate measurements. Signal fidelit...[Details]
The motor drive simulation schematic is as follows The MCU assembly language source program is as follows: ADC EQU 35H CLOCK BIT P2.4 ; define ADC0808 clock bit ST ...[Details]
Wound healing can be accelerated through exogenous electrical stimulation, which affects inflammation, bleeding, cell proliferation and migration, wound scarring, etc. The experimental new ePatch Ban...[Details]
This latest recognition marks Pure Storage’s 10th consecutive year as a leader in Gartner ’s Magic Quadrant Pure Storage ® (NYSE: PSTG) , a global IT pioneer that provides adva...[Details]