Ordering Information .................................................................................................................................................................... 2
User Programming Interface ..................................................................................................................................... 18
Start-up output frequency and signaling types ........................................................................................................... 18
Any-frequency function ............................................................................................................................................. 19
C/SPI Control Registers...................................................................................................................................................... 28
9 I
Register Address: 0x00. DCO Frequency Control Least Significant Word (LSW) .................................................... 28
Register Address: 0x01. OE Control, DCO Frequency Control Most Significant Word (MSW) ................................. 29
Register Address: 0x02. DCO PULL RANGE CONTROL ........................................................................................ 29
Register Address: 0x03. Frac-N PLL Feedback Divider Integer Value and Frac-N PLL Feedback Divider Fraction
Value MSW ............................................................................................................................................................... 30
Register Address: 0x05. Forward Divider, Driver Control ......................................................................................... 30
Register Address: 0x06. Driver Divider, Driver Control ............................................................................................. 31
2
C Operation ........................................................................................................................................................................ 32
10 I
I
2
C protocol ............................................................................................................................................................... 32
I
2
C Timing Specification ............................................................................................................................................ 35
I
2
C Device Address Modes ....................................................................................................................................... 36
Dimensions and Patterns ........................................................................................................................................................... 43
Additional Information ................................................................................................................................................................ 44
Revision History ......................................................................................................................................................................... 45
Rev 1.01
Page 3 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
1 Electrical Characteristics
All Min and Max limits in the Electrical Characteristics tables are specified over temperature and rated operating voltage with
standard output terminations shown in the termination diagrams. Typical values are at 25°C and nominal supply voltage.
Table 1. Electrical Characteristics – Common to LVPECL, LVDS and HCSL
Parameter
Output Frequency Range
Symbol
f
Min.
1
Typ.
–
–
–
–
–
±1
–
–
–
Max.
340
Unit
MHz
Condition
Factory or user programmable, accurate to 6 decimal places
Frequency Range
Frequency Stability
Frequency Stability
F_stab
-10
-20
-25
-50
First Year Aging
F_1y
–
+10
+20
+25
+50
–
ppm
ppm
ppm
ppm
ppm
°C
°C
°C
1
st
-year aging at 25°C
Inclusive of initial tolerance, operating temperature, rated
power supply voltage and load variations.
Temperature Range
Operating Temperature Range
T_use
-20
-40
-40
+70
+85
+105
Supply Voltage
Supply Voltage
Vdd
2.97
2.7
2.52
2.25
3.3
3.0
2.8
2.5
–
–
100
–
–
–
3.63
3.3
3.08
2.75
–
30%
–
V
V
V
V
Extended Commercial
Industrial
Extended Industrial. Available only for I
2
C operation, not SPI.
Input Characteristics – OE Pin
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
VIH
VIL
Z_in
70%
–
–
Vdd
Vdd
kΩ
OE pin
OE pin
OE pin, logic high or logic low
Output Characteristics
Duty Cycle
DC
45
–
–
55
%
Startup and Output Enable/Disable Timing
Start-up Time
Output Enable/Disable Time –
Hardware control via OE pin
Output Enable/Disable Time –
Software control via I
2
C/SPI
T_start
T_oe_hw
3.0
3.8
ms
µs
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin reaches rated VIH and VIL to
the time clock pins reach 90% of swing and high-Z.
See
Figure 9
and
Figure 10
Measured from the time the last byte of command is
transmitted via I
2
C/SPI (reg1) to the time clock pins reach 90%
of swing and high-Z. See
Figure 30
and
Figure 31
T_oe_sw
–
–
6.5
µs
Rev 1.01
Page 4 of 45
www.sitime.com
SiT3521
1 to 340 MHz Elite Platform I2C/SPI Programmable Oscillator
Table 2. Electrical Characteristics – LVPECL Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Maximum Output Current
Idd
I_OE
I_leak
I_driver
–
–
–
–
–
–
0.15
–
89
58
–
32
mA
mA
A
mA
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Maximum average current drawn from OUT+ or OUT-
Output Characteristics
Output High Voltage
Output Low Voltage
Output Differential Voltage Swing
Rise/Fall Time
VOH
VOL
V_Swing
Tr, Tf
Vdd - 1.1V
Vdd - 1.9V
1.2
–
–
–
1.6
225
Vdd - 0.7V
Vdd - 1.5V
2.0
290
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[3]
Note:
3. Measured according to JESD65B.
T_jitt
–
0.225
0.1
0.225
0.11
1
0.340
0.14
0.340
0.15
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
V
V
V
ps
See
Figure 5
See
Figure 5
See
Figure 6
20% to 80%, see
Figure 6
Table 3. Electrical Characteristics – LVDS Specific
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
Current Consumption
Current Consumption
OE Disable Supply Current
Output Disable Leakage Current
Idd
I_OE
I_leak
–
–
–
–
–
0.15
80
61
–
mA
mA
A
Excluding Load Termination Current, Vdd = 3.3 V or 2.5 V
OE = Low
OE = Low
Output Characteristics
Differential Output Voltage
Delta VOD
Offset Voltage
Delta VOS
Rise/Fall Time
VOD
ΔVOD
VOS
ΔVOS
Tr, Tf
250
–
1.125
–
–
–
–
–
–
400
455
50
1.375
50
470
Jitter
RMS Phase Jitter (random) –
DCO Mode Only
T_phj
–
–
RMS Phase Jitter (random) –
Any-frequency Mode Only
T_phj
–
–
RMS Period Jitter
[4]
Note:
4. Measured according to JESD65B.
T_jitt
–
0.21
0.1
0.21
0.1
1
0.275
0.12
0.367
0.12
1.6
ps
ps
ps
ps
ps
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 156.25 MHz, Integration bandwidth = 12 kHz to 20 MHz,
all Vdd levels
f = 156.25, IEEE802.3-2005 10 GbE jitter mask integration
bandwidth = 1.875 MHz to 20 MHz, all Vdd levels
f = 100, 156.25 or 212.5 MHz, Vdd = 3.3 V or 2.5 V
mV
mV
V
mV
ps
f = 156.25MHz See
Figure 7
See
Figure 7
See
Figure 7
See
Figure 7
Measured with 2 pF capacitive loading to GND, 20% to 80%,
EOS and ESD on ADC : https://training.eeworld.com.cn/course/5271This video starts with an introduction of electrical overstress, abbreviated EOS, and Electrostatic Discharge, abbreviated ESD.We will l...
Language: MicroPython
hardware:NodeMcuEsp8266 (CP2012) development board, a dozen yuan
L298N driver board - red (8.8 yuan)
Breadboard
DC motor (3V) 6.8 yuan 10 pieces
Several Dupont wires (female to f...
What is 5G IoT?5G is about a new communication system that includes a primarily New Radio (5G NR) framework and a completely new core network designed to improve wireless connectivity around the world...
My graduation project is a low-power Bluetooth design based on cc2650. I have read the user development manual of cc2650, but I have no experience in this area and don't quite understand it. How can I...
[i=s]This post was last edited by lugl4313820 on 2022-3-14 13:12[/i][Pingtou Ge RVB2601 Creative Application Development] MP3 Player - Pingtou Ge RISC-V RVB2601 Activity Zone - Electronic Engineering ...
The serial port is relatively smooth, just pay attention to the line sequence.
This example uses the interrupt method. The query method must be very simple. It is also reflected in the interrupt serv...[Details]
LeCroy oscilloscopes based on the innovative X-Stream architecture have a unique feature that allows users to limit the measurement range when using automatic measurement parameters. In addition to...[Details]
Q: Why do products need to undergo electrical safety testing?
A: This is a question that many product manufacturers want to ask the most. Of course, the most common answer is "because it is ...[Details]
"Curiosity" landed on Mars, its mission is to explore Martian resources, and the MarS Board super ARM DIY computer platform landed in the embedded world, will take you to a stronger, faster and bette...[Details]
Earlier this month, Western Digital and Kioxia both announced that some of their NAND production lines were contaminated, resulting in a loss of production capacity in the first quarter of this year....[Details]
Today we are speaking with Bob White, the originator of the PMBus power management protocol, long-time chair of the PMBus Specification Working Group and editor of the PMBus and SMBus specifications....[Details]
Mitsubishi PLC (Programmable Logic Controller) is a controller commonly used in the field of industrial automation. The accumulation instruction is a basic instruction in PLC programming, which is ...[Details]
The interrupt system of 89C51 has 5 interrupt sources: external interrupt 0, timer 0, external interrupt 1, timer 1, serial port interrupt (in descending order of priority); 2 interrupt priorities: h...[Details]
February 23, 2021, is another milestone for Kedali. Kedali and Yibin City officially signed a project contract and held a grand groundbreaking ceremony at the Yangtze River Industrial Park in S...[Details]
Preface Steps to use STM8's built-in bootloader First, confirm whether the STM8 you are using has its own bootloader. Refer to the table below STM8 empty devices can directly use their own boot...[Details]
Since the introduction of single-chip microcomputers into my country in the 1980s, the craze for learning and applying single-chip microcomputers has never diminished, especially the MCS51 series. ...[Details]
1. Clock circuit
The MCS-51 microcontroller has a high-gain inverting amplifier for forming an oscillator. Its input is the chip pin XTAL1 and its output is XTAL2. Outside the chip, a crystal oscill...[Details]
High-frequency current probes are mainly used for measuring floating ground systems. In power system testing, it is often required to measure the relative voltage difference between the live wire and...[Details]
Today, I want to talk about another important metric to consider when testing power supply performance: noise measurement. Where does power supply noise come from? Power supply noise is generated f...[Details]
The most expensive game console in history, PS5 Pro, is about to be released. An overseas blogger got one in advance and took it apart without saying a word. He found some unexpected changes.
...[Details]
MEMS sensors
京公网安备 11010802033920号
EEWORLD
