EEWORLDEEWORLDEEWORLD

Part Number

Search

AYA22HRXI

Description
Card Edge Connector, 22 Contact(s), 1 Row(s), Straight, 0.125 inch Pitch, Solder Terminal, Green Insulator, Receptacle
CategoryThe connector    The connector   
File Size247KB,3 Pages
ManufacturerSullins Connector Solutions
Environmental Compliance  
Download Datasheet Parametric View All

AYA22HRXI Overview

Card Edge Connector, 22 Contact(s), 1 Row(s), Straight, 0.125 inch Pitch, Solder Terminal, Green Insulator, Receptacle

AYA22HRXI Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1157276941
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresNONE
Board mount options#4-40 THD HOLE
body width0.33 inch
subject depth0.431 inch
body length3.575 inch
Body/casing typeRECEPTACLE
Connector typeCARD EDGE CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact completed and terminatedGold (Au) - with Nickel (Ni) barrier
Contact materialBERYLLIUM COPPER
contact modeRECTANGULAR
Contact resistance10 mΩ
Contact styleBELLOWED TYPE
Dielectric withstand voltage800VDC V
Insulation resistance5000000000 Ω
Insulator colorGREEN
insulator materialPOLYPHENYLENE SULFIDE
JESD-609 codee4
Plug contact pitch0.125 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature220 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.185 inch
Terminal pitch3.175 mm
Termination typeSOLDER
Total number of contacts22
Atmel Launches Highly Integrated Automotive Driver IC ATA6026
On May 2, Atmel announced the launch of the highly integrated ATA6026 automotive driver integrated circuit (IC), which is the first member of the new upcoming automotive driver family. The design of t...
frozenviolet Automotive Electronics
Read the good book "Operational Amplifier Parameter Analysis and LTspice Application Simulation" 07 Slew Rate and Full Power Bandwidth Case Analysis
[i=s]This post was last edited by 1nnocent on 2021-5-26 12:18[/i]I had some understanding of slew rate when I was playing with op amps before, but I had never calculated it specifically. However, it i...
1nnocent Analog electronics
About the battery life of SenSorTile.Box
I saw someone with extremely low battery life before, and I guessed that it was because of a short circuit in the circuit board. I suggest that you power on the phone first, check if the sensor in the...
梦璃 ST MEMS Sensor Creative Design Competition
Download and debug interface issues on product circuit boards
[align=left][size=14px]I am making a wearable device. The PCB area on the device is limited, so I want to save as much area as possible. [/size][/align][align=left][size=14px]Both chips on the board n...
b01010101 PCB Design
Multisim op amp output is greater than the power supply problem
When I used Multisim to simulate the op amp circuit before, I found that the op amp output was greater than the power rail. Sometimes I wanted to use the op amp as a comparator for open-loop simulatio...
fish001 Analogue and Mixed Signal
How to choose between DT4215 and 15B for multimeter selection
I am planning to buy a multimeter. Most of the use scenarios require testing voltages of 600-900V (occasionally overvoltages of 1000+), so I have been using Fluke's 15B+. The meters in the company are...
bigbat Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号