Features ....................................................................................................................................................................................... 1
Ordering Information .................................................................................................................................................................... 2
LVPECL and FlexSwing Termination .................................................................................................................................. 17
LVDS, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 18
HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V ...................................... 18
Low-power HCSL, Supply Voltage: 1.8 V
±5%,
2.5 V ±10%, 3.3 V ±10%, 2.25 V to 3.63 V, 1.71 V to 3.63 V.................... 18
Dimensions and Patterns ― 2.0 x 1.6 mm x mm ....................................................................................................................... 19
Dimensions and Patterns ― 2.5 x 2.0 mm x mm ....................................................................................................................... 20
Dimensions and Patterns ― 3.2 x 2.0 mm x mm ....................................................................................................................... 21
Revision History ......................................................................................................................................................................... 22
Rev 0.53
Page 3 of 23
www.sitime.com
SiT9375
Low Jitter Differential XO for Standard Networking Frequencies
Electrical Characteristics
ADVANCED
All Min and Max limits in the Electrical Characteristics tables are specified over operating temperature and rated operating
voltage with standard output termination shown in the termination diagrams. Typical values are at 25°C and nominal
supply voltage.
Table 3. Electrical Characteristics – Common to All Output Signaling Types
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
–
Min.
Typ.
Max.
Unit
MHz
ppm
Condition
Refer to frequencies listed in
Ordering Information
section.
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and 10 years
aging at 25°C
Inclusive of initial tolerance, operating temperature, rated power
supply voltage, load variation of 15 pF
±
10%, and first year aging
at 25°C
Ambient temperature of 25°C
Extended commercial, ambient temperature
Industrial, ambient temperature
Ambient temperature
Extended industrial, ambient temperature
Voltage-supply order code “YY”
Voltage-supply order code “XX”
Voltage-supply order code “18”.
Contact SiTime
for 1.5 V
Voltage-supply order code “25”
Voltage-supply order code “33”
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
Pins 1 and 2 for OE and SE, respectively
See
Figure 5
and
Figure 7
Measured from the time Vdd reaches its rated minimum value
Measured from the time OE pin toggles to enable logic level to
the time clock pins reach 90% of swing. See
Figure 12
Measured from the time OE pin toggles to disable logic level to
the last clock edge. See
Figure 13
12 kHz to 20 MHz offset frequency integration bandwidth,
156.25 MHz
12 kHz to 20 MHz offset frequency range, 156.25 MHz
12 kHz to 20 MHz offset frequency range, 155.52 MHz
156.25 MHz
156.25 MHz
Frequency Range
Standard frequencies
–
±20
Frequency Stability
–
–
–
10 Year Aging
Operating Temperature Range
F_10y
T_use
–
-20
-40
-40
-40
Supply Voltage
Vdd
1.71
2.25
1.71
2.25
2.97
Input Voltage High
Input Voltage Low
Input Pull-up Impedance
Duty Cycle
Startup Time
Output Enable Time
Output Disable Time
VIH
VIL
Z_in
DC
T_start
T_oe
T_od
70%
–
–
45
–
–
–
–
–
–
±1
–
–
–
–
–
–
1.80
2.50
3.30
–
–
100
–
1
–
–
±25
±30
±50
–
+70
+85
+95
+105
ppm
ppm
ppm
ppm
°C
°C
°C
°C
V
V
V
V
V
Temperature Range
Supply Voltage
3.63
3.63
1.89
2.75
3.63
Input Characteristics
–
Vdd
30%
–
55
5
100+3 clock
cycles
100+3 clock
cycles
Vdd
kΩ
%
ms
ns
ns
Output Characteristics
Startup, OE and SE Timing
Jitter and Phase Noise
RMS Phase Jitter (random)
Spurious Phase Noise
RMS Period
Jitter
[1]
Jitter
[1]
T_phj
PN_spur_a
PN_spur_b
T_jitt_per
T_jitt_cc
Peak Cycle-to-cycle
–
–
–
–
–
200
-110
-80
1
6
–
–
–
–
–
fs
dBc
dBc
ps
ps
Note:
1. Measured according to JESD65B.
Rev 0.53
Page 4 of 23
www.sitime.com
SiT9375
Low Jitter Differential XO for Standard Networking Frequencies
ADVANCED
Table 4. Electrical Characteristics – LVPECL
|
Supply voltages: 2.5 V
±10%,
3.3 V
±10%,
2.25 V to 3.63 V
Parameter
Current Consumption, Output
Enabled without Termination
Current Consumption, Output
Enabled with Termination 1
Current Consumption, Output
Enabled with Termination 2
Current Consumption, Output
Disabled without Termination
Current Consumption Output
Disabled with Termination 1
Current Consumption, Output
Disabled with Termination 2
OE Leakage Current
Symbol
Idd_oe_nt
Idd_oe_wt1
Idd_oe_wt2
Idd_od_nt
Idd_od_wt1
Idd_od_wt2
I_leak
Min.
–
–
–
–
–
–
–
Typ.
43
52
71
58
58
86
37
Max.
–
–
–
–
–
–
–
Unit
mA
mA
mA
mA
mA
mA
mA
Condition
Excluding load termination current
Including load termination current. See
Figure 15
for
termination
Including load termination current. See
Figure 18
for
termination
Excluding load termination current
Including load termination current. See
Figure 15
for
termination
Including load termination current. See
Figure 18
for
termination
OE = disable logic, DC termination, OUTP and OUTN held
Today, I will use Raspberry Pi to build a TCP server and use HTTP communication. Without further ado, let's get started.
First check whether the curl library is installed on the Raspberry Pi;
Enter th...
According to the theory of signals and systems, after the signal is modulated by AM , the spectrum shifting effect will occur.
TGF4042 can generate AM signals. By using the FFT function of an oscillos...
Touch and grab a building to win gifts: How much do you know about RISC-V manufacturers?
Last day of activity
Are there any netizens who can continue to post?
Click here to enter the building grabPlea...
Recently, I made a TFT screen SPI driver. Since the MISO pin is not used for unidirectional data writing, the SPI is configured as SPI_Direction_1Line_Tx mode. However, when debugging, I found that th...
Capacitive touch technology has been used in kitchen appliances for several years, for example in ovens and frying pans, with discrete buttons behind opaque glass panels. These touch controls have gra...
[i=s]This post was last edited by Jack315 on 2021-1-25 00:52[/i]The transfer function of a single zero is:The Bode plot of the zero point is shown below:On the amplitude-frequency characteristic graph...
Single-chip microcomputer is the abbreviation of single-chip microcomputer. It is made by integrating CPU, ROM, RAM, TIMER/COUNTER and input/output interface (I/O) on a large-scale integrated circu...[Details]
Fingerprint locks are highly sought after by high-end families! Installing fingerprint locks on your door not only facilitates our daily life and work, but also reflects the quality and taste of mo...[Details]
In Part 1, we have set up the SPI bus on the AVR ATMEGA328P microcontroller. Now we can start using SPI. Set the relevant pins Before we get started, we need to set up the pins for the SPI bus ...[Details]
On March 21, according to The Paper, CATL revealed that the company’s flagship technology, Kirin batteries, has achieved mass production. The Paper also pointed out that as the first mass-produced ...[Details]
The "OFweek 2024 (13th) China Robotics Industry Conference" hosted
by OFweek, a Chinese high-tech portal, and organized by OFweek Robotics
was
successfully held in Shenzhen from April ...[Details]
In the evening, I continued to learn about the watchdog of LPC2103.
Overview of Watchdog:
The watchdog includes a 4-frequency prescaler and a 32-bit counter. The clock is input into the timer t...[Details]
Hardware environment: I2C Master: STM8S003 I2C slave: HTU21D Control mode: Hardware IIC Problem Description: During the normal operation of the program, unplug the device power and quickly plug...[Details]
Introduction
With the continuous improvement and improvement of power automation technology, more and more small hydropower stations have adopted computer control equipment. While improving the...[Details]
Today, Zhuan Zhuan, a second-hand trading platform created by 58 Ganji Group, announced the 2020 "Brick First Prize", and models from brands such as Huawei and Xiaomi were on the list. The winner o...[Details]
1. Project Overview 1.1 Introduction The GSM wireless intelligent transformer integrated alarm system based on AVR designed in this project aims to provide a wireless intelligent transformer inte...[Details]
When it comes to implantable medical devices, saving space is one of the most critical design issues. This article reviews packaging concepts that can reduce the space required for electronic power...[Details]
Preface
Multi-
sensor
information fusion technology is an important method in the current field of intelligent information processing. The so-called multi-sensor information fusion ...[Details]
Fully self-driving cars may be on the road in the next few years. But according to foreign media reports, General Motors has still applied for a new patent for its computer that understands d...[Details]
1 Introduction In practical applications, controlling the physical parameters of the controlled object (temperature, humidity, displacement, current, voltage, etc.) within a certain range is one of...[Details]
On October 30, early this morning Beijing time, Reuters quoted people familiar with the matter as saying that OpenAI is working with Broadcom and TSMC to develop its first self-developed AI chip, a...[Details]
Special Edition for Assessment Centres
京公网安备 11010802033920号
EEWORLD
