Resistor values are typically 120 to 240 ohms for 3.3V operation and 82 to 120 ohms for 2.5V
operation.
Figure 7 - Pull Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is optional, depending on the application and the input logic requirements of
the next stage.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
LVDS Application Diagrams
+3.3V
VC
10nF
1nF
1
6
Receiver
100
3
4
3
4
1
6
10nF
100
Receiver
VC
+3.3V
10nF
1nF
OE
2
5
OE
2
5
10nF
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need additional components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
I registered EEWORLD when I was in college around 2008.
Later I forgot the password of that account so I couldn't log in. I had to register again and could only choose the name Common Ze1From college ...
Smart sensors: key applications in medicine, health and the environment
https://download.eeworld.com.cn/detail/sigma/622401Principles and maintenance of common medical equipment CT machine
https://dow...
[i=s]This post was last edited by xiaolinen on 2022-10-12 22:08[/i]1. Narrative
This test was conducted according to the Telink B91 BLE Single Connection SDK Developer Handbook document, mainly to mea...
This migration guide describes the hardware and software differences to be aware of when migrating between the F28004x and F28002x C2000 MCUs. This document provides block diagrams of the two MCUs to ...
As a general test and measurement tool, the oscilloscope is usually used to qualitatively test the signal characteristics of a circuit. But sometimes we also need to analyze the sporadic characterist...[Details]
This is not a power plant in the traditional sense.
Here is an innovative platform based on the ubiquitous power Internet of Things, which can access 11 types of ubiquitous adjustable resource...[Details]
From December 18 to 20, 2014, the "2014 China Photovoltaic Industry Top 50 Innovation List Release and Award Ceremony" (PV TOP 50) and PV CHINA International Photovoltaic Exhibition were held in Sh...[Details]
/**************************************************************************************************************
AT89S52+12MHZ+TEA5767 digital tube display FM radio
This program uses digital t...[Details]
A paper published in Nature Communications on the 14th describes a flexible patch that can convert throat muscle movements into speech with the help of machine learning. With further development, t...[Details]
Is it troublesome to repair the R&S oscilloscope RTE1204? What should I do if the R&S oscilloscope RTE1204 fails? Have you ever encountered out-of-tolerance conditions on the R&S oscilloscope RTE1204...[Details]
According to Jiwei.com, "The stock price has been halved and continues to fall. It has an advantageous track but cannot deliver results. It has frequently acquired high-quality assets but has been op...[Details]
In May 2009, the State Grid Corporation of China officially announced the "Strong Smart Grid" plan to the outside world. The launch of the smart grid plan will drive major changes in grid productio...[Details]
"Turn left and the car will go right; turn right and the car will go left." This magical operation is achieved by changing parameter settings. This is the wire-controlled steering system developed by...[Details]
use Provide clock input for PIC microcontroller. The following circuit is the clock unit circuit of PIC microcontroller. Schematic Principle and technical indicators Resistor Rs is used to pr...[Details]
Today, a key feature that LED driver ICs must have is the ability to adequately dim LEDs. Since LEDs are driven with a constant current, where the DC current value is proportional to the brightnes...[Details]
Today, industry insider Ross Young revealed that Huawei's upcoming P50 Pocket will be a dual-screen design and will be the first dual-screen flagship in Huawei's P series. The main screen will b...[Details]
Link address
Startup Process
The sample code is as follows:
start.S file
.globl _start
_start:
/*Hardware related settings*/
ldr r0,=0x70000000
...[Details]
1 Introduction
With the rapid development and maturity of power electronics technology, large-scale power electronic devices in power systems are increasing. While improving ...[Details]
Auto-coupling step-down starting and star-delta starting are two commonly used motor starting methods. They have different effects on the current and torque of the motor during the starting process...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
