AEC-Q100 with extended temperature range (-55°C to 125°C)
Frequencies between 115.2 MHz and 137 MHz accurate to
6 decimal points
100% pin-to-pin drop-in replacement to quartz-based XO
Excellent total frequency stability as low as ±20 ppm
Industry best G-sensitivity of 0.1 PPB/G
Low power consumption of 3.8 mA typical at 1.8V
LVCMOS/LVTTL compatible output
Industry-standard packages: 2.0 x 1.6, 2.5 x 2.0, 3.2 x 2.5,
5.0 x 3.2, 7.0 x 5.0 mm x mm
RoHS and REACH compliant, Pb-free, Halogen-free and
Antimony-free
Automotive, extreme temperature and other high-rel
electronics
Infotainment systems, collision detection devices, and
in-vehicle networking
Powertrain control
Electrical Characteristics
Table 1. Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise
stated. Typical values are at 25°C and nominal supply voltage.
Parameter
Output Frequency Range
Frequency Stability
Symbol
f
F_stab
Min.
115.20
-20
-25
-30
-50
Operating Temperature
Range (ambient)
T_use
-40
-40
-40
-55
Supply Voltage
Current Consumption
Vdd
Idd
1.62
2.25
–
–
Duty Cycle
Rise/Fall Time
Output High Voltage
DC
Tr, Tf
VOH
45
–
–
90%
Typ.
–
–
–
–
–
–
–
–
–
Max.
Unit
Condition
Frequency Range
137
MHz
Refer to
Tables 13 to 15
for the exact list of supported frequencies
Frequency Stability and Aging
Inclusive of Initial tolerance at 25°C, 1
st
year aging at 25°C, and
+20
ppm
variations over operating temperature, rated power supply voltage
+25
ppm
and load (15 pF ± 10%).
+30
ppm
+50
ppm
Operating Temperature Range
+85
°C
AEC-Q100 Grade 3
+105
+125
+125
°C
°C
°C
AEC-Q100 Grade 2
AEC-Q100 Grade 1
Extended cold, AEC-Q100 Grade1
Supply Voltage and Current Consumption
All voltages between 2.25V and 3.63V including 2.5V, 2.8V, 3.0V and 3.3V
1.8
1.98
V
are supported. Contact
SiTime
for 1.5V support
–
3.63
V
6
4.9
–
1.5
1.5
–
8
6
mA
mA
No load condition, f = 125 MHz, Vdd = 2.25V to 3.63V
No load condition, f = 125 MHz, Vdd = 1.62V to 1.98V
LVCMOS Output Characteristics
55
%
3
2.5
–
ns
ns
Vdd
Vdd = 2.25V - 3.63V, 20% - 80%
Vdd = 1.8V, 20% - 80%
IOH = -4 mA (Vdd = 3.0V or 3.3V)
IOH = -3 mA (Vdd = 2.8V and Vdd = 2.5V)
IOH = -2 mA (Vdd = 1.8V)
IOL = 4 mA (Vdd = 3.0V or 3.3V)
IOL = 3 mA (Vdd = 2.8V and Vdd = 2.5V)
IOL = 2 mA (Vdd = 1.8V)
Output Low Voltage
VOL
–
–
10%
Vdd
Input High Voltage
Input Low Voltage
Input Pull-up Impedance
Startup Time
Enable/Disable Time
Standby Current
VIH
VIL
Z_in
T_start
T_oe
I_std
70%
–
–
–
–
–
–
–
–
–
100
–
–
2.6
1.4
0.6
Input Characteristics
–
Vdd
Pin 1, OE
30%
–
Vdd
kΩ
Pin 1, OE
Pin 1, OE logic high or logic low
Startup and Resume Timing
5.5
ms
Measured from the time Vdd reaches its rated minimum value
130
–
–
–
ns
µA
µA
µA
f = 115.20 MHz. For other frequencies, T_oe = 100 ns + 3 * cycles
Vdd = 2.8V to 3.3V,
ST
= Low, Output is weakly pulled down
Vdd = 2.5V,
ST
= Low, Output is weakly pulled down
Vdd = 1.8V,
ST
= Low, Output is weakly pulled down
Rev 1.7
May 22, 2019
www.sitime.com
SiT8925B
High Frequency, Automotive AEC-Q100 Oscillator
Table 1. Electrical Characteristics (continued)
Parameter
RMS Period Jitter
Peak-to-peak Period Jitter
RMS Phase Jitter (random)
Symbol
T_jitt
T_pk
T_phj
Min.
–
–
–
–
–
–
Typ.
1.6
1.8
12
14
0.7
1.5
Max.
2.5
3
20
30
–
–
Unit
Jitter
ps
ps
ps
ps
ps
ps
f = 125 MHz, 2.25V to 3.63V
f = 125 MHz, 1.8V
f = 125 MHz, Vdd = 2.5V, 2.8V, 3.0V or 3.3V
f = 125 MHz, Vdd = 1.8V
f = 125 MHz, Integration bandwidth = 900 kHz to 7.5 MHz
f = 125 MHz, Integration bandwidth = 12 kHz to 20 MHz
Condition
Table 2. Pin Description
Pin
Symbol
Output Enable
1
OE/NC
No Connect
2
3
4
GND
OUT
VDD
Power
Output
Power
Functionality
H
[1]
: specified frequency output
L: output is high impedance. Only output driver is disabled.
Any voltage between 0 and Vdd or Open
[1]
: Specified frequen-
cy output. Pin 1 has no function.
Electrical ground
[2]
Oscillator output
Power supply voltage
[2]
GND
2
Top View
OE/NC
1
4
VDD
3
OUT
Figure 1. Pin Assignments
Notes:
1. In OE mode, a pull-up resistor of 10kΩ or less is recommended if pin 1 is not externally driven. If pin 1 needs to be left floating, use the NC option.
2. A capacitor of value 0.1 µF or higher between Vdd and GND is required.
Rev 1.7
Page 2 of 19
www.sitime.com
SiT8925B
High Frequency, Automotive AEC-Q100 Oscillator
Table 3. Absolute Maximum Limits
Attempted operation outside the absolute maximum ratings may cause permanent damage to the part. Actual performance
of the IC is only guaranteed within the operational specifications, not at absolute maximum ratings.
Parameter
Storage Temperature
Vdd
Electrostatic Discharge
Soldering Temperature (follow standard Pb free soldering guidelines)
Junction Temperature
[3]
Note:
3. Exceeding this temperature for extended period of time may damage the device.
Min.
-65
-0.5
–
–
–
Max.
150
4
2000
260
150
Unit
°C
V
V
°C
°C
Table 4. Thermal Consideration
[4]
Package
7050
5032
3225
2520
2016
θ
JA, 4 Layer Board
(°C/W)
142
97
109
117
152
θ
JA, 2 Layer Board
(°C/W)
273
199
212
222
252
θ
JC, Bottom
(°C/W)
30
24
27
26
36
Note:
4. Refer to JESD51 for
θJA
and
θJC
definitions, and reference layout used to determine the
θJA
and
θJC
values in the above table.
Table 5. Maximum Operating Junction Temperature
[5]
Max Operating Temperature (ambient)
85°C
105°C
125°C
Maximum Operating Junction Temperature
93°C
113°C
133°C
Note:
5. Datasheet specifications are not guaranteed if junction temperature exceeds the maximum operating junction temperature.
Table 6. Environmental Compliance
Parameter
Mechanical Shock
Mechanical Vibration
Temperature Cycle
Solderability
Moisture Sensitivity Level
Condition/Test Method
MIL-STD-883F, Method 2002
MIL-STD-883F, Method 2007
JESD22, Method A104
MIL-STD-883F, Method 2003
MSL1 @ 260°C
Rev 1.7
Page 3 of 19
www.sitime.com
SiT8925B
High Frequency, Automotive AEC-Q100 Oscillator
Test Circuit and Waveform
Vdd
Vout
Test
Point
tr
80% Vdd
tf
4
Power
Supply
0.1µF
3
15pF
(including probe
and fixture
capacitance)
50%
20% Vdd
High Pulse
(TH)
Period
Low Pulse
(TL)
1
2
Vdd
OE/NC Function
1k
Ω
Figure 2. Test Circuit
[6]
Note:
6. Duty Cycle is computed as Duty Cycle = TH/Period.
Figure 3. Waveform
Timing Diagrams
90% Vdd
Vdd
50% Vdd
T_oe
Vdd
Pin 4 Voltage
T_start
No Glitch
during start up
OE Voltage
CLK Output
HZ
CLK Output
HZ
T_start: Time to start from power-off
T_oe: Time to re-enable the clock output
Figure 4. Startup Timing (OE Mode)
[7]
Figure 5. OE Enable Timing (OE Mode Only)
Vdd
OE Voltage
50% Vdd
T_oe
CLK Output
HZ
T_oe: Time to put the output in High Z mode
Figure 6. OE Disable Timing (OE Mode Only)
Note:
7. SiT8925 has “no runt” pulses and “no glitch” output during startup or resume.
EMC (Electromagnetic CompaTIbility) is a technology that studies electromagnetic interference. Electromagnetic interference is the electromagnetic energy around us that causes the operation of electro...
How big is the tax control machine market in China? At the tax control machine industry chain forum held in Beijing recently, Zheng Zhiguang, secretary general of the Tax Control Information Equipment...
Next, I was going to start learning ROS, but it was particularly difficult to install it on the Raspberry Pi operating system. I tried to install ROS on the 32-bit buster operating system for a long t...
I also bought an OLED from Wannengdi Taobao, but I didn’t receive it during the Labor Day holiday, but I did receive it at work.
I turned it on at night and liked it so much that I wanted to light it ...
Thyristors are divided into unidirectional thyristors and bidirectional thyristors. Here are the detection methods for these two thyristors!
1. Detection of unidirectional thyristor
The multim...[Details]
Scientists at Peter the Great St.Petersburg Polytechnic University (SPbPU) are developing a technique to print electrodes for tiny lithium-ion batteries using an inkjet printer . The ongoing research...[Details]
first day What resources are available? 1. An MPU6050 2. A stm32f103rc minimum system version with ucos3 ported to it, running several tasks, including an LCD task (lowest priority) 3.st firmware lib...[Details]
The LTC®2217 is a 16-bit A/D converter with a sampling rate of 105Msps, designed for digitizing high frequency, wide dynamic range signals with input frequencies up to 400MHz. The input range of th...[Details]
The next thing that comes to mind after GPIO is the Universal Synchronous/Asynchronous Receiver/Transmitter (USART). For more complex programs, using LEDs to debug is obviously a bit unscientific. Th...[Details]
There is a prerequisite for LED to have a long life and high efficiency, that is, suitable working conditions. The main factor affecting the life and luminous efficiency is the working junction tem...[Details]
Device Regulation
In an effort to reduce regulatory oversight of diagnostic and radiological devices, the FDA is taking further steps to exempt some devices from premarket regulation. In d...[Details]
I recently used STM8F103 + SI4432 to tune the wireless, and encountered many problems. Here I refer to the experience of predecessors; 1. When the hardware board was given to me, the USB burning ca...[Details]
1. Introduction
In the field of measurement and control, it is usually required to transmit multiple detection signals. The transmission of signals is often interfered by the complex environme...[Details]
In 2016, VR ushered in a golden age, and many manufacturers viewed VR games as a blue ocean market worth exploring. With the unique advantages of high immersion and strong interactivity, VR games, as...[Details]
Shanghai, June 30, 2023 – As the world's leading provider of test and measurement solutions, Rohde & Schwarz (hereinafter referred to as "R&S Company") recently launched the "Connectivity Release" at...[Details]
American scientist Daniel Nocera recently announced the latest progress of his research team at the 241st Annual Meeting of the American Chemical Society - a cheap and efficient "artificial leaf". ...[Details]
Edge Computing Developer Competition Launched, Intel and Partners Accelerate Industry Ecosystem Innovation August 26, 2021, Beijing - The Edge Computing Developer Competition, co-organized by the C...[Details]
According to DIGITIMES Research, the silicon carbide (SiC) power semiconductor market will take off, and the electric vehicle field will become the main driving force. SiC power semiconductors have t...[Details]
1. Background
Modbus and Profibus are two commonly used communication protocols in industrial control systems. They play an important role in the field of automation. Modbus is a serial commun...[Details]
Power technology
京公网安备 11010802033920号
EEWORLD
